Emerson Rosemount 702 Manual de usuario

www.rosemount.com

¢00825-0100-4648[¤

Quick Installation Guide

00825-0100-4702, Rev BA

August 2009 Rosemount 702

Step 1: Physical Installation

Step 2: Verify Operation

Step 3: Reference Information

Product Certifications

EC Declaration of Conformity

Start

End

Rosemount 702 Wireless Discrete Transmitter

00825-0100-4702_Rev_BA.fm Page 1 Tuesday, August 18, 2009 8:52 AM

Quick Installation Guide

00825-0100-4702, Rev BA

August 2009

Rosemount 702

IMPORTANT NOTICE

This installation guide provides basic guidelines for the Rosemount®702. It does not

provide instructions for detailed configuration, diagnostics, maintenance, service,

troubleshooting, or installations. Refer to the Rosemount 702 reference manual

(document number 00809-0100-4702) for more instruction. The manual and this QIG are

also available electronically on www.rosemount.com.

WARNING

Explosions could result in death or serious injury:

Installation of this transmitter in an explosive environment must be in accordance with the

appropriate local, national, and international standards, codes, and practices. Please

review the Product Certifications section for any restrictions associated with a safe

installation.

• Before connecting a 375 Field Communicator in an explosive atmosphere, ensure the

instruments are installed in accordance with intrinsically safe or non-incendive field

wiring practices.

Electrical shock can result in death or serious injury

• Avoid contact with the leads and terminals. High voltage that may be present on leads

can cause electrical shock.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

conditions. This device may not cause harmful interference. This device must accept any

interference received, including interference that may cause undesired operation.

This device must be installed to ensure a minimum antenna separation distance of 8 in.

(20 cm) from all persons.

The power module may be replaced in a hazardous area. The power module has surface

resistivity greater than one gigaohm and must be properly installed in the wireless device

enclosure. Care must be taken during transportation to and from the point of installation to

prevent electrostatic charge build-up.

IMPORTANT NOTICE

The Rosemount 702 and all other wireless devices should be installed only after the 1420

Wireless Gateway has been installed and is functioning properly. Wireless devices should

also be powered up in order of proximity from the 1420 Wireless Gateway, beginning with

the closest. This will result in a simpler and faster network installation.

Emerson Process Management

Rosemount Division

8200 Market Boulevard

Chanhassen, MN USA 55317

T (US) (800) 999-9307

T (Intnl) (952) 906-8888

F (952) 949-7001

Rosemount Temperature GmbH

Frankenstrasse 21

63791 Karlstein

Germany

T 49 (6188) 992 0

F 49 (6188) 992 112

Emerson Process Management

Asia Pacific Private Limited

1 Pandan Crescent

Singapore 128461

T (65) 6777 8211

F (65) 6777 0947 / (65) 6777 0743

Enquiries@AP.EmersonProcess.com

00825-0100-4702_Rev_BA.fm Page 2 Tuesday, August 18, 2009 8:52 AM

Quick Installation Guide

00825-0100-4702, Rev BA

August 2009 Rosemount 702

IMPORTANT NOTICE

Shipping considerations for wireless products (Lithium Batteries):

The unit was shipped to you without the battery installed. Please remove the battery pack

prior to shipping the unit.

Primary lithium batteries are regulated in transportation by the U.S. Department of

transportation, and are also covered by IATA (International Air Transport Association),

ICAO (International Civil Aviation Organization), and ARD (European Ground

Transportation of Dangerous Goods). It is the responsibility of the shipper to ensure

compliance with these or any other local requirements. Please consult current regulations

and requirements before shipping.

00825-0100-4702_Rev_BA.fm Page 3 Tuesday, August 18, 2009 8:52 AM

Quick Installation Guide

00825-0100-4702, Rev BA

August 2009

Rosemount 702

STEP 1: PHYSICAL INSTALLATION

The Rosemount 702 and all other wireless devices should be installed only after the 1420

Wireless Gateway has been installed and is functioning properly. Wireless devices should

also be powered up in order of proximity from the 1420 Wireless Gateway, beginning with

the closest. This will result in a simpler and faster network installation.

The Rosemount 702 can be installed in one of two configurations: Direct Mount, where the

switch is connected directly to the 702 housing’s conduit entry, or Remote Mount, where the

switch is mounted separate from the 702 housing, then connected to the 702 via conduit.

Choose the installation sequence that corresponds to the mounting configuration.

Direct Mount

The direct mount installation should not be used when installing with a Swagelok®fitting.

1. Install the switch according to standard installation practices. Be sure to use thread

sealant on all connections.

2. Attach the 702 housing to the switch using the threaded conduit entry.

3. Attach the switch wiring to the terminals as indicated on the wiring diagram.

4. Connect the battery pack.

NOTE:

Wireless devices should be powered up in order of proximity from the 1420 Wireless

Gateway, beginning with the closest device to the 1420. This will result in a simpler

and faster network installation.

5. Close the housing cover and tighten to safety specification. Always ensure a proper seal

by installing the electronics housing covers so that metal touches metal, but do not over

tighten.

6. Position the antenna such that it is vertical, either straight up or straight down.

Possible antenna rotation shown.

Antenna rotation allows for best

installation practices in any

configuration.

00825-0100-4702_Rev_BA.fm Page 4 Tuesday, August 18, 2009 8:52 AM

Quick Installation Guide

00825-0100-4702, Rev BA

August 2009 Rosemount 702

STEP 1 CONTINUED...

Remote Mount

1. Install the switch according to standard installation practices. Be sure to use thread

sealant on all connections.

2. Run wiring (and conduit if necessary) from the switch to the 702.

3. Pull the wiring through the threaded conduit entry of the 702.

4. Attach the switch wiring to the terminals as indicated on the wiring diagram.

5. Connect the battery pack.

NOTE:

Wireless devices should be powered up in order of proximity from the 1420 Wireless

Gateway, beginning with the closest device to the 1420. This will result in a simpler

and faster network installation.

6. Close the housing cover and tighten to safety specification. Always ensure a proper seal

by installing the electronics housing covers so that metal touches metal, but do not over

tighten.

7. Position the antenna such that it is vertical, either straight up or straight down.

00825-0100-4702_Rev_BA.fm Page 5 Tuesday, August 18, 2009 8:52 AM

Quick Installation Guide

00825-0100-4702, Rev BA

August 2009

Rosemount 702

STEP 2: VERIFY OPERATION

Operation can be verified in four locations: at the device via the LCD, by using the 375 Field

Communicator, at the Gateway via the 1420 Wireless Gateway’s integrated web server, or

via AMS™Suite: Intelligent Device Manager.

Local Display

During normal operation, the LCD should display the PV value at the update rate up to 1

minute intervals. Refer to the Rosemount 702 Manual for error codes and other LCD

messages. Press the Diagnostic button to display the TAG, Device ID, Network ID,

Network Join Status and Device Status screens.

375 Field Communicator

For HART Wireless transmitter communication, a 702 DD is required.

Figure 1. 375 Field Communicator Connections

1420 Wireless Gateway

In the 1420’s integrated web server, navigate to the Explorer>Status page. This page will

show whether the device has joined the network and if it is communicating properly.

NOTE:

It may take several minutes for the device to join the network.

Searching for Network Joining Network Connected with

1 Parent Connected with

2 Parents

Function Key Sequence Menu Items

Network 1, 4 Smart Power, Network ID, Set Join

Key, Radio State

n e t w k

A -s r c h

n e t w k

J O I N G

n e t w k

1 P A R N T

n e t w k

2 P A R N T

COMM

P/N00753-9200-0020

00825-0100-4702_Rev_BA.fm Page 6 Tuesday, August 18, 2009 8:52 AM

Quick Installation Guide

00825-0100-4702, Rev BA

August 2009 Rosemount 702

NOTE:

If the device joins the network and immediately has an alarm present, it is likely due

to sensor configuration. Check the sensor wiring (see Rosemount 702 Terminal

Diagram on page 9) and the sensor configuration (see 702 Fast Key Sequence on

page 9).

Figure 2. 1420 Network Settings

AMS™Suite: Intelligent Device Manager

When the device has joined the network, it will appear in the Device Manager as illustrated

below.

00825-0100-4702_Rev_BA.fm Page 7 Tuesday, August 18, 2009 8:52 AM

Quick Installation Guide

00825-0100-4702, Rev BA

August 2009

Rosemount 702

Troubleshooting

If the device is not operating properly, refer to the troubleshooting section of the manual. The

most common cause of incorrect operation is the Network ID and Join Key. The Network ID

and Join Key in the device must match that of the 1420 Wireless Gateway.

The Network ID and Join Key may be obtained from the 1420 Wireless Gateway on the

Setup>Network>Settings page on the web server (see Figure 2: 1420 Network Settings on

page 7). The Network ID and Join Key may be changed in the wireless device by using the

following Fast Key sequence.

Function Key Sequence Menu Items

Network 1, 4 Smart Power, Network ID, Set Join

Key, Radio State

00825-0100-4702_Rev_BA.fm Page 8 Tuesday, August 18, 2009 8:52 AM

Quick Installation Guide

00825-0100-4702, Rev BA

August 2009 Rosemount 702

STEP 3: REFERENCE INFORMATION

Figure 3. Rosemount 702 Terminal Diagram

NOTE:

In order to communicate with a 375 Field Communicator, the device must be powered

by connecting the battery pack.

Table 1. 702 Fast Key Sequence

Figure 4. 375 Field Communicator Connections

Figure 5. 702 Lead Wire Configurations - Switch Connections Diagram

If switch is grounded, the grounded connection must be connected to one of the CMN terminals.

Function Key Sequence Menu Items

Device Information 1, 3, 4, 2 Tag, Date, Descriptor, Message, Model, Model Number I,

II, III, Write Protect, Revision Numbers, Transmitter Serial

Numbers, Device ID

Wireless 1, 4, 3 Smart Power, Network ID, Set Join Key, Radio State

Discrete Input Configuration 1, 3, 2, 1 Output configuration, Discrete Input Configuration

Single SPST Dual SPST Single SPDT

COMM

P/N00753-9200-0020

(1)

(2)

(1)

(2)

(3)

(4)

Sensor 1

Sensor 2

(1) Normally Open

(2) Common

(3) Normally Closed

00825-0100-4702_Rev_BA.fm Page 9 Tuesday, August 18, 2009 8:52 AM

Quick Installation Guide

00825-0100-4702, Rev BA

August 2009

Rosemount 702

PRODUCT CERTIFICATIONS

Approved Manufacturing Locations

Rosemount Inc. – Chanhassen, Minnesota, USA

Emerson Process Management GmbH & Co. - Karlstein, Germany

Emerson Process Management Asia Pacific Private Limited - Singapore

European Union Directive Information

The EC Declaration of Conformity begins on page 15, and the most recent revision can be

found at www.rosemount.com under Documentation.

Telecommunication Compliance

All wireless devices require certification to ensure that they adhere to regulations regarding

the use of the RF spectrum. Nearly every country requires this type of product certification.

Emerson is working with governmental agencies around the world to supply fully compliant

products and remove the risk of violating country directives or laws governing wireless

device usage.

FCC and IC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

conditions: This device may not cause harmful interference. This device must accept any

interference received, including interference that may cause undesired operation.

This device must be installed to ensure a minimum antenna separation distance of 20 cm

from all persons.

Ordinary Location Certification for FM

As standard, the transmitter has been examined and tested to determine that the design

meets basic electrical, mechanical, and fire protection requirements by FM, a nationally

recognized testing laboratory (NRTL) as accredited by the Federal Occupational Safety and

Health Administration (OSHA).

00825-0100-4702_Rev_BA.fm Page 10 Tuesday, August 18, 2009 8:52 AM

Otros manuales para Rosemount 702

Tabla de contenidos

Otros manuales de Transmisor de Emerson

Emerson

Emerson Rosemount 3051N Manual de usuario

Emerson

Emerson MICRO MOTION 2700 Manual de usuario

Emerson

Emerson Rosemount 3051 Series Manual de usuario

Emerson

Emerson Rosemount 702 Manual de usuario

Emerson

Emerson Rosemount 2051L Manual de usuario

Emerson

Emerson 5301HxxxxxxxxxxxxxxZZSeries Manual de usuario

Emerson

Emerson Rosemount 848T Manual de usuario

Emerson

Emerson Rosemount 1408H Manual de usuario

Emerson

Emerson Micro Motion 2400S Manual de usuario

Emerson

Emerson Micro Motion 4200 Manual de usuario

Emerson

Emerson Rosemount 2090P Manual de usuario

Emerson

Emerson Rosemount 2240S Manual de usuario

Emerson

Emerson Rosemount OCX 8800 Manual de usuario

Emerson

Emerson Rosemount 644R Manual de usuario

Emerson

Emerson Rosemount 5408 Manual de usuario

Emerson

Emerson Rosemount 3051 Manual de usuario

Emerson

Emerson Rosemount 3095FC MultiVariable Manual de usuario

Emerson

Emerson Rosemount 705 Manual de usuario

Emerson

Emerson Rosemount 3051S Series Manual de usuario

Emerson

Emerson Rosemount 1056 Manual de usuario

Emerson

Emerson Rosemount 327T Manual de usuario

Emerson

Emerson Rosemount 3408 Manual de usuario

Emerson

Emerson Rosemount 648 Manual de usuario

Emerson

Emerson Rosemount Analytical HART 5081-A-HT Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario