Emerson Rosemount 3051S Series Manual de usuario

Quick Start Guide

00825-0100-4805, Rev FB

June 2016

Rosemount™3051S Series Pressure Transmitter

and Rosemount 3051SF Series Flowmeter

with FOUNDATION™fieldbus Protocol

June 2016

Quick Start Guide

NOTICE

This guide provides basic guidelines for Rosemount 3051S Series Pressure Transmitters. It also provides the

basic electronics guidelines for the Rosemount 3051SFA Reference Manual and Rosemount 3051SFC

Reference Manual. It does not provide instructions for diagnostics, maintenance, service, or

troubleshooting. Refer to the Rosemount 3051S FOUNDATION fieldbus Reference Manual for more

instruction. This document is also available electronically on EmersonProcess.com/Rosemount.

Explosions can result in death or serious injury.

Do not remove the transmitter covers in explosive environments when the circuit is live.

Both transmitter covers must be fully engaged to meet explosion-proof requirements.

Make sure the instrument is installed in accordance with intrinsically safe or nonincendive field wiring

practices.

Process leaks may cause harm or result in death.

To avoid process leaks, only use the O-ring designed to seal with the corresponding flange adaptor.

Electrical shock can result in death or serious injury.

Avoid contact with the leads and the terminals. High voltage that may be present on leads can cause

electrical shock.

Contents

Mount the transmitter. . . . . . . . . . . . . . . . . . . . . 3

Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Consider housing rotation . . . . . . . . . . . . . . . . . 8

Connect wiring and power up . . . . . . . . . . . . . . 8

Verify configuration . . . . . . . . . . . . . . . . . . . . . . 10

Trim the transmitter. . . . . . . . . . . . . . . . . . . . . . 12

Product Certifications . . . . . . . . . . . . . . . . . . . . 13

Quick Start Guide

June 2016

1.0 Mount the transmitter

1.1 Liquid flow applications

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so the

drain/vent valves are oriented upward.

1.2 Gas flow applications

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

1.3 Steam flow applications

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Flow

June 2016

Quick Start Guide

Figure 1. Panel and Pipe Mounting

Panel mount Pipe mount

Coplanar flange

Traditional flange

In-line

Housings

PlantWeb™Junction box Remote mount display

Quick Start Guide

June 2016

1.4 Bolting considerations

If the transmitter installation requires assembly of the process flanges, manifolds,

or flange adapters, follow these assembly guidelines to ensure a tight seal for

optimal performance characteristics of the transmitters. Use only bolts supplied

with the transmitter or sold by Emerson™Process Management as spare parts.

Figure 2 illustrates common transmitter assemblies with the bolt length required

for proper transmitter assembly.

Figure 2. Common Transmitter Assemblies

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional manifold and flange adapters

Bolts are typically carbon steel or stainless steel. Confirm the material by viewing

the markings on the head of the bolt and referencing Table 1. If bolt material is

not shown in Table 1, contact the local Emerson Process Management

representative for more information.

Use the following bolt installation procedure:

1. Carbon steel bolts do not require lubrication and the stainless steel bolts are

coated with a lubricant to ease installation. However, no additional lubricant

should be applied when installing either type of bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern.

See Table 1 for initial torque value.

4. Torque the bolts to the final torque value using the same crossing pattern.

See Table 1 for final torque value.

5. Verify the flange bolts are protruding through the isolator plate before

applying pressure.

4 × 1.75-in.

(44 mm)

4 × 1.75-in.

(44 mm)

4 × 2.25-in.

(57 mm)

4 ×1.75-in.

(44 mm) 4 ×1.50-in.

(38 mm)

4 × 2.88-in.

(73 mm)

June 2016

Quick Start Guide

1.5 O-rings with flange adapters

Table 1. Torque Values for the Flange and Flange Adaptor Bolts

Bolt material Head markings Initial torque Final torque

Carbon Steel (CS) 300 in-lb 650 in-lb

Stainless Steel (SST) 150 in-lb 300 in-lb

Failure to install proper flange adaptor O-rings may cause process leaks, which can result in death or

serious injury. The two flange adapters are distinguished by unique O-ring grooves. Only use the

O-ring that is designed for its specific flange adaptor, as shown below:

A. Flange adaptor

B. O-ring

C. PTFE based (profile is square)

D. Elastomer (profile is round)

Whenever the flanges or adapters are removed, visually inspect the O-rings. Replace them if there are

any signs of damage, such as nicks or cuts. If you replace the O-rings, re-torque the flange bolts and

alignment screws after installation to compensate for seating of the PTFE O-ring.

B7M

316

STM

316

B8M

Rosemount 3051S/3051/2051/3095

Rosemount 1151

Quick Start Guide

June 2016

1.6 In-line gage transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage

transmitter is located under the sensor module neck label. (See Figure 3.)

Keep the vent path free of any obstruction, including but not limited to paint,

dust, and lubrication by mounting the transmitter so any contaminants can drain

away.

Figure 3. In-line Gage Transmitter

A. Low side pressure port (under neck label)

2.0 Tagging

2.1 Commissioning (paper) tag

To identify which device is at a particular location, use the removable tag

provided with the transmitter. Ensure the physical device tag (PD Tag field) is

properly entered in both places on the commissioning tag. Tear off the bottom

portion of the tag and write “physical tag” on this portion. This can now be given

to the person who can associate the device ID to the desired tag.

Figure 4. Commissioning Tag

Revision: 23

Device Serial Number:

XXXXXXXXXX

Device ID:

0011513051010001440-121698091725

PD Tag:

Tear Here

COMMISSIONING TAG

Device ID:

0011513051010001440-121698091725

PD Tag:

PT- 101

Revision: 23

Support files available at

EmersonProcess.com/Rosemount

PT-101

Support files available at

EmersonProcess.com/Rosemount

June 2016

Quick Start Guide

Note

The device description loaded in the host system must be at the same revision as this

device. The device description can be downloaded from EmersonProcess.com/Rosemount

or Fieldbus.org.

3.0 Consider housing rotation

To improve field access to wiring or to better view the optional LCD display:

1. Loosen the housing rotation set screw.

2. First, rotate the housing clockwise to the desired location. If the desired

location cannot be achieved due to thread limit, rotate the housing counter

clockwise to the desired location (up to 360° from thread limit).

3. Retighten the housing rotation set screw.

Figure 5. Transmitter Housing Set Screw

A. Housing rotation set screw (3/32-in.)

4.0 Connect wiring and power up

4.1 Cable connection

The segment cable can enter the transmitter through either conduit connection

on the housing. Cable entering the housing vertically should be avoided. Drip

loops are recommended for installations where moisture can accumulate and

enter the terminal compartment.

4.2 Power supply

The transmitter requires between 9 and 32 Vdc (9 and 15 Vdc for FISCO) at the

terminals to operate and provide complete functionality.

4.3 Power conditioner

A fieldbus segment requires a power conditioner to isolate the power supply filter

and decouple the segment from other segments attached to the same power

supply.

PlantWeb Junction box

Quick Start Guide

June 2016

4.4 Signal termination

Every fieldbus segment requires terminators at each end of the segment. Failure

to properly terminate segments may cause communication errors with devices

on the segment.

4.5 Transient protection

Transient protection devices require the transmitter be grounded for proper

operation. Refer to Grounding for further information.

4.6 Grounding

Grounding terminations are provided on the sensor module and inside the

terminal compartment. These grounds are used when transient protect terminal

blocks are installed or to fulfill local regulations.

1. Remove the FIELD TERMINALS housing cover.

2. Connect the wiring pair and ground as indicated in Figure 6.

a. The terminals are not polarity sensitive.

b. The cable shield should:

Be trimmed close and insulated from touching the transmitter housing

Continuously connect to the termination point

Be connected to a good earth ground at the power supply end

Figure 6. Wiring

3. Replace the housing cover. It is recommended the cover be tightened until

there is no gap between the cover and the housing.

4. Plug and seal unused conduit connections.

A. Insulate shield D. Trim shield and insulate

B. Minimize distance E. Safety ground

C. Connect shield back to the power supply ground

NOTICE

The enclosed pipe plug must be installed in unused conduit opening with a minimum of five thread

engagement to comply with explosion-proof requirements. Refer to the Rosemount 3051S

FOUNDATION fieldbus Reference Manual for more information. This manual is also available

electronically on EmersonProcess.com/Rosemount.

June 2016

Quick Start Guide

5.0 Verify configuration

Use the following block examples to do basic configuration to the transmitter. For

more advanced configurations see the Rosemount 3051S FOUNDATION fieldbus

Reference Manual.

Note

DeltaV™users should use DeltaV Explorer for the resource and transducer blocks and

Control Studio for the function blocks.

5.1 To configure the AI block

AI block configuration parameters

Use the Pressure, DP Flow, and DP Level examples for guides.

Note

Only select the units that are supported by the device.

Pressure example

Note

Only select the units that are supported by the device.

Parameters Enter data

Channel 1 = Pressure or 2 = Sensor temp or 3 = Mass flow

L_Type Direct, indirect, or square root

XD_Scale Scale and engineering units

Pa bar inH2O @ 68 °F psi inHg @ 0 °C

kPa mbar mmH2O @ 68 °F g/cm2mmHg @ 0 °C

MPa atm ftH2O @ 68 °F kg/cm2mmH2O @ 4 °C

torr inH2O @ 4 °C

Out_Scale Scale and engineering units

Parameters Enter data

Channel 1

L_Type Direct

XD_Scale See list of supported engineering units.

Out_Scale Set values outside operating range.

Otros manuales para Rosemount 3051S Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de Emerson

Emerson

Emerson Rosemount 708 Manual de usuario

Emerson

Emerson Rosemount 644 Manual de usuario

Emerson

Emerson Rosemount 2051HT Manual de usuario

Emerson

Emerson Rosemount 3051 Manual de usuario

Emerson

Emerson Micro Motion Manual de usuario

Emerson

Emerson Rosemount OCX 8800 Manual de usuario

Emerson

Emerson Rosemount ET310C Manual de usuario

Emerson

Emerson Net Safety Millennium II Manual de usuario

Emerson

Emerson Rosemount 644h Manual de usuario

Emerson

Emerson Rosemount OCX8800A Manual de usuario

Emerson

Emerson Rosemount 3051 Manual de usuario

Emerson

Emerson Micro Motion 5700 Guía rápida

Emerson

Emerson Rosemount 3095 Manual de usuario

Emerson

Emerson Rosemount 3051 Manual de usuario

Emerson

Emerson Rosemount 2051HT Manual de usuario

Emerson

Emerson Rosemount 3051S Series Manual de usuario

Emerson

Emerson Rosemount 3308 Series Manual de usuario

Emerson

Emerson PT5N FLR Series Manual de usuario

Emerson

Emerson Rosemount 56 Manual de usuario

Emerson

Emerson Rosemount 3051N Manual de usuario

Emerson

Emerson Rosemount 1066 Manual de usuario

Emerson

Emerson Micro Motion 2400S Guía rápida

Emerson

Emerson Rosemount 4088B MultiVariable Manual de usuario

Emerson

Emerson Rosemount 2051L Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario