Emerson Rosemount 644h Manual de usuario

Quick Start Guide

00825-0100-4829, Rev EB

April 2019

Rosemount™ 644H Temperature

Transmitters

with FOUNDATION™Fieldbus Protocol

Safety messages

NOTICE

This guide provides basic guidelines for installing the Rosemount™ 644 Temperature Transmitter. It

does not provide instructions for detailed configuration, diagnostics, maintenance, service,

troubleshooting, or installation. Refer to the Rosemount 644 Reference Manual for more instruction.

The manual and this guide are also available electronically on Emerson.com/Rosemount.

Important

Read this manual before working with the product. For personal and system safety, and for optimum

product performance, make sure to thoroughly understand the contents before installing, using, or

maintaining this product. The United States has two toll-free assistance numbers and one international

number.

Customer Central: 1-800-999-9307 (7:00 a.m. to 7:00 p.m. Central Standard Time)

National Response Center: 1-800-654-7768 (24 hours a day). Equipment service needs

International: 1-(952)-906-8888

WARNING

Follow instructions

Failure to follow these installation guidelines could result in death or serious injury.

Ensure only qualified personnel perform the installation.

WARNING

Explosions

Explosions could result in death or serious injury.

Installation of the transmitters in a hazardous environment must be in accordance with the

appropriate local, national, and international standards, codes, and practices. Please review the

Product Certifications section for any restrictions associated with a safe installation.

Do not remove the connection head cover in explosive atmospheres when the circuit is live.

Before connecting a handheld communicator in an explosive atmosphere, ensure the instruments

are installed in accordance with intrinsically safe or non-incendive field wiring practices.Verify the

operating atmosphere of the transmitter is consistent with the appropriate hazardous locations

certifications.

All connection head covers must be fully engaged to meet explosion-proof requirements.

WARNING

Process leaks

Process leaks could result in death or serious injury.

Do not remove the thermowell while in operation.

Install and tighten thermowells and sensors before applying pressure.

Quick Start Guide April 2019

2 Rosemount 644H

WARNING

Electrical shock

Electrical shock could cause death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Contents

Mount the transmitter................................... 5

Wire and apply power.................................... 8

Ground the transmitter................................11

Verify tagging.............................................. 15

Verify transmitter configuration...................16

Product certifications...................................18

April 2019 Quick Start Guide

Quick Start Guide 3

Quick Start Guide April 2019

4 Rosemount 644H

1 Mount the transmitter

Mount the transmitter at a high point in the conduit run to prevent moisture

from draining into the transmitter housing.

1.1 Install connection head

Head mount transmitter with DIN plate style sensor.

Procedure

1. Attach the thermowell to the pipe or process container wall. Install

and tighten the thermowell before applying process pressure.

2. Assemble the transmitter to the sensor. Push the transmitter

mounting screws through the sensor mounting plate and insert the

snap rings (optional) into the transmitter mounting screw groove.

3. Wire the sensor to the transmitter.

4. Insert the transmitter-sensor assembly into the connection head.

Thread the transmitter mounting screws into the connection head

mounting holes. Assemble the extension to the connection head.

Insert the assembly into the thermowell.

5. Slip the shielded cable though the cable gland.

6. Attach the cable gland into the shielded cable.

7. Insert the shielded cable leads into the connection head through the

cable entry. Connect and tighten the cable gland.

8. Connect the shielded power cable leads to the transmitter power

terminals.

Avoid contact with sensor leads and sensor connections.

9. Install and tighten the connection head cover.

WARNING

Enclosure covers must be fully engaged to meet explosion-proof

requirements.

April 2019 Quick Start Guide

Quick Start Guide 5

Example

A. Rosemount™ 644 Transmitter

B. Connection head

C. Thermowell

D. Transmitter mounting screws

E. Integral mount sensor with flying leads

F. Extension

1.2 Install universal head

Head mount transmitter with threaded sensor.

Procedure

1. Attach the thermowell to the pipe or process container wall. Install

and tighten thermowells before applying process pressure.

2. Attach necessary extension nipples and adapters to the thermowell.

Seal the nipple and adapter threads with silicone tape.

3. Screw the sensor into the thermowell. Install drain seals if required

for severe environments or to satisfy code requirements.

4. Verify the correct installation of Integral Transient Protection (option

code T1).

a) Ensure the transient protector unit is firmly connected to the

transmitter puck assembly.

b) Ensure the transient protector power leads are adequately

secured under the transmitter power terminal screws.

c) Verify the transient protector’s ground wire is secured to the

internal ground screw found within the universal head.

Note

The transient protector requires the use of an enclosure of at least

3.5-in. (89 mm) in diameter.

5. Pull the sensor wiring leads through the universal head and

transmitter. Mount the transmitter in the universal head by

Quick Start Guide April 2019

6 Rosemount 644H

threading the transmitter mounting screws into the universal head

mounting holes.

6. Mount the transmitter-sensor assembly into the thermowell. Seal

adapter threads with silicone tape.

7. Install conduit for field wiring to the conduit entry of the universal

head. Seal conduit threads with PTFE tape.

8. Pull the field wiring leads through the conduit into the universal

head. Attach the sensor and power leads to the transmitter.

Avoid contact with other terminals.

9. Install and tighten the universal head cover.

Enclosure covers must be fully engaged to meet explosion-proof

requirements.

Example

ABC

A. Threaded thermowell

B. Standard extension

C. Threaded style sensor

D. Universal head (transmitter and LCD inside)

E. Conduit entry

April 2019 Quick Start Guide

Quick Start Guide 7

2 Wire and apply power

Wiring diagrams are located inside the terminal block cover.

An external power supply is required to power a Fieldbus segment.

The power required across the transmitter power terminals is 9 to 32 Vdc

(the power terminals are rated to 32 Vdc). To prevent damaging the

transmitter, do not allow terminal voltage to drop below 9 Vdc when

changing the configuration parameters.

2.1 Power filter

A Fieldbus segment requires a power conditioner to isolate the power supply

filter and decouple the segment from other segments attached to the same

power supply.

2.2 Power the transmitter

Procedure

1. Remove the terminal block cover (if applicable).

2. Connect the power lead to the power terminals.

The Rosemount™ 644H with FOUNDATION™ Fieldbus is polarity

insensitive.

If a transient protector is being used, the power leads will now be

connected to the top of the transient protector unit.

3. Tighten the terminal screws.

When tightening the sensor and power wires, the max torque is 6 in-

lb. (0.7 N-m).

4. Reattach and tighten the cover (if applicable).

5. Apply power (9–32 Vdc).

Quick Start Guide April 2019

8 Rosemount 644H

1 2 3 4

A. Sensor terminals

B. Communication terminals

C. Power terminals

Example

Figure 2-1: Sensor Connections

Two-wire RTD and

Three-wire RTD(1)

and Ω

Four-wire RTD(2)

and Ω

T/C and mV

(1) Emerson provides four-wire sensors for all single element RTDs. Use these RTDs

in three-wire configurations by leaving the unneeded leads disconnected and

insulated with electrical tape.

(2) The transmitters must be configured for at least a three-wire RTD in order to

recognize an RTD with a compensation loop.

April 2019 Quick Start Guide

Quick Start Guide 9

Figure 2-2: Typical Configuration for Fieldbus Networking

A. 6234 ft. (1900 m) max, depending upon cable characteristics

B. Integrated power conditioner and filter

C. Terminators

D. Power supply

E. Trunk

F. Spur

G. Foundation Fieldbus configuration tool

H. Devices 1 through 16

I. Power/signal wiring

Note

The power supply, filter, first terminator, and configuration tool are typically

located in the control room.

Note

Each segment in a Fieldbus trunk must be terminated at both ends.

Quick Start Guide April 2019

10 Rosemount 644H

Otros manuales para Rosemount 644h

Tabla de contenidos

Otros manuales de Transmisor de Emerson

Emerson

Emerson Rosemount 3051S Series Guía de configuración

Emerson

Emerson Rosemount 6888A Manual de usuario

Emerson

Emerson Fisher 4210 Manual de usuario

Emerson

Emerson Micro Motion 2400S Manual de usuario

Emerson

Emerson Rosemount 708 Manual de usuario

Emerson

Emerson Rosemount 5300 Series Manual operacional

Emerson

Emerson Rosemount 702 Manual de usuario

Emerson

Emerson Rosemount 4088B MultiVariable Manual de usuario

Emerson

Emerson Rosemount 8732EM Manual de usuario

Emerson

Emerson Rosemount 248 Manual de usuario

Emerson

Emerson Rosemount 8732E Manual de usuario

Emerson

Emerson Rosemount CX1100 Manual de usuario

Emerson

Emerson Rosemount 848T Manual de usuario

Emerson

Emerson Fisher 4200 Series Manual de usuario

Emerson

Emerson 5301HxxxxxxxxxxxxxxZZSeries Manual de usuario

Emerson

Emerson Rosemount 248 Manual de usuario

Emerson

Emerson Rosemount ET410 Manual de usuario

Emerson

Emerson Rosemount 248 Manual de usuario

Emerson

Emerson Rosemount 2051HT Manual de usuario

Emerson

Emerson Rosemount 2240S Manual de usuario

Emerson

Emerson Rosemount 1208C Manual de usuario

Emerson

Emerson 6081-P Manual de usuario

Emerson

Emerson Rosemount 4600 Manual de usuario

Emerson

Emerson Fisher 4200 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario