Emerson Rosemount 5300 Series Manual de usuario

Quick Start Guide

00825-0100-4530, Rev HA

February 2019

Rosemount™ 5300 Level Transmitter

Guided Wave Radar

Contents

About this guide............................................ 3

Confirm system readiness (HART® only).........5

Mount transmitter on tank.............................6

Prepare the electrical connections............... 11

Connect wiring and power up...................... 19

Configure.....................................................22

Safety Instrumented Systems (4-20 mA only)..

Adjust probe length..................................... 26

Product certifications...................................29

Quick Start Guide February 2019

2 Rosemount 5300 Level Transmitter

1 About this guide

This Quick Start Guide provides basic guidelines for the Rosemount 5300

Level Transmitter. Refer to the Rosemount 5300 Reference Manual for more

instructions. The manual and this guide are also available electronically on

Emerson.com/Rosemount.

WARNING

Failure to follow safe installation and servicing guidelines could result in death

or serious injury.

•Make sure the transmitter is installed by qualified personnel and in

accordance with applicable code of practice.

•Use the equipment only as specified in this Quick Start Guide and the

Reference Manual. Failure to do so may impair the protection provided by

the equipment.

•Any substitution of non-recognized parts may jeopardize safety. Repair,

e.g. substitution of components etc., may also jeopardize safety and is

under no circumstances allowed.

Explosions could result in death or serious injury.

•Verify that the operating atmosphere of the transmitter is consistent with

the appropriate hazardous locations certifications.

•To prevent ignition of flammable or combustible atmospheres, disconnect

power before servicing.

•Before connecting a handheld communicator in an explosive atmosphere,

ensure the instruments are installed in accordance with intrinsically safe or

non-incendive field wiring practices.

•To avoid process leaks, only use the O-ring designed to seal with the

corresponding flange adapter.

Electrical shock could cause death or serious injury.

•Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

•Make sure the mains power to the transmitter is off and the lines to any

other external power source are disconnected or not powered while

wiring the transmitter.

•Ground device on non-metallic tanks (e.g. fiberglass tanks) to prevent

electrostatic charge build-up.

February 2019 Quick Start Guide

Quick Start Guide 3

WARNING

Probes with non-conducting surfaces

•Probes covered with plastic and/or with plastic discs may generate an

ignition-capable level of electrostatic charge under certain extreme

conditions. Therefore, when the probe is used in a potentially explosive

atmosphere, appropriate measures must be taken to prevent electrostatic

discharge.

Eliminate the risk of ESD discharge prior to dismounting the transmitter head

from the probe.

•Probes may generate an ignition-capable level of electrostatic charge

under extreme conditions. During any type of installation or maintenance

in a potentially explosive atmosphere, the responsible person should

make sure that any ESD risks are eliminated before attempting to separate

the probe from the transmitter head.

Quick Start Guide February 2019

4 Rosemount 5300 Level Transmitter

2 Confirm system readiness (HART® only)

2.1 Confirm HART® revision capability

If using HART based control or asset management systems, confirm the HART

capability of those systems prior to transmitter installation. Not all systems

are capable of communicating with HART Revision 7 protocol.

Transmitters with a firmware version 2F0 or later can be configured for either

HART Revision 5 or 7.

2.2 Confirm correct device driver

Procedure

•Verify that the latest Device Driver (DD/DTM™) is loaded on your systems

to ensure proper communication. See Table 2-1.

•Download the latest Device Driver from Emerson.com/DeviceInstallKits.

Table 2-1: Rosemount 5300 Device Revisions and Files

Firmware version (1) Find Device Driver

HART® Universal

Revision

Device Revision (2)

2F0 or later 7 4

5 3

2A2 - 2E0 5 3

(1) Firmware version is printed on the transmitter head label, e.g. SW 2E0 or can

be found in Rosemount Radar Master (select Device > Properties).

(2) Device revision is printed on the transmitter head label, e.g. HART Dev Rev 4.

2.3 Switch HART® revision mode

If the HART configuration tool is not capable of communicating with HART

Revision 7, the device will load a generic menu with limited capability. To

switch the HART revision mode from the generic menu:

Procedure

1. Locate the “Message” field.

2. In the Message field, enter HART5 or HART7 and then 27 trailing

spaces.

February 2019 Quick Start Guide

Quick Start Guide 5

3 Mount transmitter on tank

For flexible single lead probes ordered with weight unmounted (option code

WU), refer to Adjust probe length before mounting the transmitter.

3.1 Threaded/Flange/Tri-Clamp® tank connection

Procedure

1. Seal and protect the threads.

Only for NPT threaded tank connection.

Use anti-seize paste or PTFE tape according to your site procedures.

2. Mount the device on tank.

$&%

A. NPT

B. Flange

C. Gasket

Quick Start Guide February 2019

6 Rosemount 5300 Level Transmitter

&&$%

A. Tri-Clamp

B. BSP/G

C. Gasket

3. (Optional) Adjust display orientation.

4. Tighten the nut.

Torque 30 ft-lb (40 Nm)

February 2019 Quick Start Guide

Quick Start Guide 7

3.2 Install remote housing

Procedure

1. Carefully remove the transmitter.

2. Mount the probe on tank.

A. Gasket

3. Mount the remote connection on the probe.

Torque 30 ft-lb (40 Nm)

Quick Start Guide February 2019

8 Rosemount 5300 Level Transmitter

4. Mount the bracket to the pipe.

A. Horizontal pipe

B. Vertical pipe

5. Fasten the housing support.

6. Mount the transmitter head.

Torque 30 ft-lb (40 Nm)

February 2019 Quick Start Guide

Quick Start Guide 9

3.3 Bracket mounting

Procedure

1. Mount the bracket to the pipe/wall.

On pipe:

A. Horizontal pipe

B. Vertical pipe

On wall:

2. Mount the transmitter with probe to the bracket.

Quick Start Guide February 2019

10 Rosemount 5300 Level Transmitter

Otros manuales para Rosemount 5300 Series

Tabla de contenidos

Otros manuales de Transmisor de Emerson

Emerson

Emerson Rosemount 1408H Manual de usuario

Emerson

Emerson Rosemount 702 Manual de usuario

Emerson

Emerson Rosemount 3144P Manual de usuario

Emerson

Emerson PT5-30L-FLR Manual de usuario

Emerson

Emerson Rosemount 702DX22 Manual de usuario

Emerson

Emerson CSI 9420 Manual de usuario

Emerson

Emerson Rosemount 2051 Wireless Series Manual de usuario

Emerson

Emerson Rosemount 3051S Series Manual de usuario

Emerson

Emerson Micro Motion 5700 Manual de usuario

Emerson

Emerson Rosemount 2088 Manual de usuario

Emerson

Emerson ROSEMOUNT 5300 Manual de usuario

Emerson

Emerson Rosemount 1057 Manual de usuario

Emerson

Emerson Micro Motion 5700 Manual de usuario

Emerson

Emerson Micro Motion 4700 Manual de usuario

Emerson

Emerson Rosemount 705 Manual de usuario

Emerson

Emerson Rosemount 6888A Manual de usuario

Emerson

Emerson Rosemount 3051 Manual de usuario

Emerson

Emerson ROSEMOUNT 5081-A Manual de usuario

Emerson

Emerson Rosemount 3051HT Manual de usuario

Emerson

Emerson Micro Motion 1000 Series Guía rápida

Emerson

Emerson Rosemount 148 Manual de usuario

Emerson

Emerson Micro Motion Transmitters and Discrete Controllers Series... Manual operacional

Emerson

Emerson Rosemount ET410 Manual de usuario

Emerson

Emerson Rosemount OCX8800A Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario