Emerson Rosemount 700XA Hoja de instrucciones
Manual
7R00077, Rev A
June 2022
Install power supply
For Rosemount™ 700XA Gas Chromatograph
Safety information
NOTICE
The analyzer electronics and oven assembly, when housed inside a purged enclosure, meet the certifications and classifications
identified in the Specifications section of the Product Data Sheet, which is located on the Emerson website: emerson.com.
WARNING
Safety compliance
Failure to follow the safety instructions may cause injury to personnel. The seller does not accept any responsibility for installations
of the device or any attached equipment in which the installation or operation thereof has been performed in a manner that is
negligent and/or non-compliant with applicable safety requirements.
Install and operate all equipment as designed and comply with all safety requirements.
If the device is not operated in a manner recommended by the manufacturer, the overall safety could be impaired.
Observe all safety precautions defined in the gas Safety Data Sheet (SDS), especially for hazardous locations.
WARNING
Supply mains connection
The device is intended to be connected to supply mains by qualified personnel in accordance with local and national codes.
WARNING
Explosion
Failure to de-energize the analyzer may cause an explosion and severely injure personnel.
Before opening the analyzer, disconnect all electrical power and ensure that the area is free of explosive gases.
Keep cover tight while circuits are live.
Use cables or wires suitable for the marked "T" ratings.
Cover joints must be cleaned before replacing the cover.
Conduit runs to the enclosure must have sealing fitting adjacent to enclosure.
WARNING
Power
A suitable APPROVED switch and fuse or a circuit breaker shall be provided to facilitate the disconnection of mains power.
WARNING
Ventilation
Use the device in a well-ventilated area.
If you plan to place the device in a sealed shelter, always vent it to atmosphere with 0.25 in (6.4 mm) tubing or larger. This will
prevent the build up of H2 and sample gas.
WARNING
Leak testing
All gas connections must be properly leak tested at installation.
Do not turn on gas until you have completely checked the carrier lines for leaks.
2
WARNING
Precautionary signs
Failure to observe precautionary signs may result in injury or death to personnel or cause damage to equipment.
Observe and comply with all precautionary signs posted on the device.
WARNING
Toxic vapors
Exit ports may discharge dangerous levels of toxic vapors.
Use proper protection and a suitable exhaust device.
WARNING
Burns
Some parts of the analyzer may be heated to 248 °F (120 °C).
To prevent burns, do not touch any of the hot parts. All parts of an analyzer are always hot unless it has been switched off and
allowed to cool down.
Before fitting, removing, or performing any maintenance on the analyzer, make sure that it has been switched off and allowed
to cool for at least two hours.
When handling the analyzer, always use suitable protective gloves.
These precautions are particularly important when working at heights.
If burned, seek medical treatment immediately.
WARNING
Physical access
Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end users’ equipment. This could
be intentional or unintentional and needs to be protected against.
Physical security is an important part of any security program and fundamental to protecting your system. Restrict physical access
by unauthorized personnel to protect end users' assets. This is true for all systems used within the facility.
NOTICE
Replaceable parts
Only a few parts inside the device are replaceable. Only trained service personnel should replace parts.
All replacement parts must be authorized by Emerson to ensure product certification compliance.
NOTICE
Equipment damage
If the device is heated without carrier flow, damage to the columns may occur.
NOTICE
Waste disposal
Waste electrical and electronic products must not be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
3
NOTICE
The device is certified by CSA and ATEX. See the certification tag on the device for specific details about its agency approvals.
When the vapor regulators and flow switches are fitted, they must be suitably certified with the ratings Ex d IIC Gb T6/T4/T3 and
for a minimum ambient temperature range: Ta = -20 °C to +60 °C.
Where right angle bend cable adapters are used, they shall be appropriately certified and shall interface with enclosures via
appropriate certified barrier glands.
4
Contents Manual
June 2022 7R00077
6 Emerson.com/Rosemount
1 Replace AC/DC power supply
The AC/DC power supply is mounted on the left wall of the lower enclosure adjacent to the
card cage. To access it, remove the front panel and the switch panel or local operator
interface (LOI) from the lower enclosure.
WARNING
Explosion
Failure to de-energize the analyzer may cause an explosion and severely injure personnel.
Before opening the analyzer, disconnect all electrical power and ensure that the area is
free of explosive gases.
Keep cover tight while circuits are live.
Use cables or wires suitable for the marked "T" ratings.
Cover joints must be cleaned before replacing the cover.
Conduit runs to the enclosure must have sealing fitting adjacent to enclosure.
Figure 1-1: AC/DC power supply in lower compartment
Prerequisites
A Cross point #2 Phillips screwdriver is required to remove and replace the AC/DC power
supply.
Procedure
1. Remove power from the gas chromatograph (GC).
Manual Replace AC/DC power supply
7R00077 June 2022
Rosemount 700XA 7
2. Unscrew and remove the front panel.
Figure 1-2: Removing the front panel
3. Unscrew and remove the switch panel or LOI to allow access to the card cage.
Figure 1-3: Removing the switch panel or LOI
Replace AC/DC power supply Manual
June 2022 7R00077
8 Emerson.com/Rosemount
4. If present, remove the clear cover from the card cage.
Figure 1-4: Card cage
5. Unplug all the cards in the card cage but do not remove them.
6. Unscrew the three switch panel connector posts. Remove the washers as well.
7. Lift the card cage with the boards and remove it from the lower enclosure.
8. Unscrew and remove the post closest to the power supply.
9. Unplug the connector at the top of the power supply on the left.
10. Unplug the low voltage cable connected along the lower edge of the backplane.
11. Disconnect the ground lead from the power supply at the chassis ground
immediately inside the lower enclosure opening.
12. Remove the nut just above the power supply. Twist the power supply free of the
attaching stud and lift it from its anchor plate. Remove the power supply carefully
to avoid damage due to wire interferences.
13. Using a Phillips screwdriver, remove the two screws attaching the anchor plate to
the inside of the enclosure.
14. Remove the anchor plate through the front opening of the enclosure.
Manual Replace AC/DC power supply
7R00077 June 2022
Rosemount 700XA 9
15. The replacement power supply is shipped with the new anchor plate attached to it
with a nut. Remove this nut to separate the new power supply and anchor plate.
Figure 1-5: Replacement power supply
A. Anchor plate
B. Nut
C. Replacement power supply
Replace AC/DC power supply Manual
June 2022 7R00077
10 Emerson.com/Rosemount
Otros manuales para Rosemount 700XA
2
Otros manuales de Fuente de alimentación de Emerson
Emerson
Emerson PACSystems RX3i Manual de usuario
Emerson
Emerson NetSure-48 VDC Power System Manual de usuario
Emerson
Emerson Branson LPX Manual de usuario
Emerson
Emerson ControlWave GFC Manual de usuario
Emerson
Emerson Appleton U-Line ECP-1523 Manual de usuario
Emerson
Emerson ASTEC Helios Candeo AP6C75AA Manual de usuario
Emerson
Emerson Series 600 Manual de usuario
Emerson
Emerson NetSure 501 A50 Manual de usuario
Emerson
Emerson NetSure 5100 Manual de usuario
Emerson
Emerson Sola HD GLQ250 Series Manual
Emerson
Emerson ALP-130 Manual de usuario
Emerson
Emerson SAG581126000 Guía del usuario
Emerson
Emerson Liebert Power Solutions Manual de usuario
Emerson
Emerson Remote Power Monitor Panel Manual de usuario
Emerson
Emerson Nfinity 208 Manual de usuario
Emerson
Emerson Metro MPS-4009 Guía de configuración
Emerson
Emerson SMP Series Manual de usuario
Emerson
Emerson DCX S Manual de usuario
Emerson
Emerson Bristol ControlWave PAC Redundancy Instrucciones de funcionamiento y seguridad
Emerson
Emerson SmartPower 701PBK Manual de usuario
