Emerson ALP-130 Manual de usuario
Information furnished by EMERSON Motion Control is believed to be accurate and
reliable. However, no responsibility is assumed by EMERSON Motion Control for its use.
EMERSON Motion Control reserves the right to change the design or operation of the
equipment described herein and any associated motion products without notice.
EMERSON Motion Control also assumes no responsibility for any errors that may appear
in this document. Information in this document is subject to change without notice.
P/N 400514-01
Rev.: A2
Date: October 22, 1999
© 1999 EMERSON Motion Control. All rights reserved.
ALP-130 and ALP-430
Auxiliary Logic Power Supply
Installation Manual
ii
© 1999 EMERSON Motion Control. All rights reserved.
Part Number: 400514-01
Revision: A2
Date: October 1999
Printed in United States of America
Information in this document is subject to change without notice.
Companies, names, and data used in examples herein are fictitious
unless otherwise noted. No part of this document may be reproduced or
transmitted in any form or by any means, electronic or mechanical, for
any purpose, without the express written permission of EMERSON
Motion Control.
The following are trademarks of EMERSON Motion Control and may
not be reproduced in any fashion without written approval of
EMERSON Motion Control.
Microsoft, Excel and Windows are registered trademarks of Microsoft Corporation.
IBM is a registered trademark of International Business Machines, Inc.
Modbus is a trademark of Modicon, Inc.
Data Highway Plus is a trademark of Allen-Bradley
Schaffner is a trademark of Schaffner
Commercial names of products from other manufacturers or developers
that appear in this manual are registered or unregistered trademarks
of those respective manufacturers or developers, which have expressed
neither approval nor disapproval of EMERSON Motion Control.
This document has been prepared to conform to the current released version of the
hardware and software system. Because of our extensive development efforts and our
desire to further improve and enhance the product, inconsistencies may exist between the
product and documentation in some instances. Call your customer support representative if
you encounter an inconsistency.
iii
Customer Service
EMERSON Motion Control
12005 Technology Drive
Eden Prairie, Minnesota 55344-3620
U.S.A.
Telephone: (612) 995-8000 or (800) 397-3786
It is EMERSON Motion Control’s goal to ensure your greatest
possible satisfaction with the operation of our products. We are
dedicated to providing fast, friendly, and accurate assistance.
That is why we offer you so many ways to get the support you
need. Whether it’s by phone, fax or modem, you can access
EMERSON Motion Control support information 24 hours a
day, seven days a week. Our wide range of services include:
FAX (612) 995-8011
You can FAX questions and comments to EMERSON Motion
Control. Just send a FAX to the number listed above.
Website and Email www.emersonmotioncontrol.com
Website: www.emersonmotioncontrol.com
Email: [email protected]
If you have Internet capabilities, you also have access to
technical support using our website. The website includes
technical notes, frequently asked questions, release notes and
other technical documentation. This direct technical support
connection lets you request assistance and exchange software
files electronically.
iv
ALP-130 and ALP-430 Auxiliary Logic Power Supply Installation Manual
Technical Service (612) 995-8033
Email: [email protected]
EMERSON Motion Control’s products are backed by a team of
professionals who will service your installation wherever it
may be. Our technical service center in Minneapolis,
Minnesota is ready to help you solve those occasional problems
over the telephone. Our technical service center is available 24
hours a day for emergency service to help speed any problem
solving. Also, all hardware replacement parts, should they ever
be needed, are available through our service organization.
When you call, please be at your computer, have your
documentation in hand, and be prepared to provide the
following information:
•Product version number, found by choosing About from the
Help menu.
•The type of controller or product you are using.
•Exact wording of any messages that appear on your screen.
•What you were doing when the problem occurred.
•How you tried to solve the problem.
Need on-site help? EMERSON Motion Control provides
service, in most cases, the next day. Just call EMERSON’s
technical service center when on-site service or maintenance is
required.
Training Services (612) 995-8000
Email: [email protected]
EMERSON Motion Control maintains a highly trained staff of
instructors to familiarize customers with EMERSON Motion
v
Control’s products and their applications. A number of courses
are offered, many of which can be taught in your plant upon
request.
Application Engineering (612) 995-8003
Email: [email protected]
An experienced staff of factory application engineers provides
complete customer support for tough or complex applications.
Our engineers offer you a broad base of experience and
knowledge of electronic motion control applications.
Customer Service (Sales) (612) 995-8000
Email: [email protected]
Authorized EMERSON Motion Control distributors may place
orders directly with our Order Processing Department by
calling the number listed above. For information on your local
distributor, call EMERSON Motion Control.
Document Conventions
Manual conventions have been established to help you learn to
use this manual quickly and easily. As much as possible, these
conventions correspond to those found in other Microsoft
Windows documentation.
Menu names and options are printed in bold type: the File
menu.
Dialog box names begin with uppercase letters: the Axis Limits
dialog box.
Dialog box field names are in quotes: “Field Name”.
vi
ALP-130 and ALP-430 Auxiliary Logic Power Supply Installation Manual
Button names are in italic: OK button.
Source code is printed in Courier font: Case ERMS.
In addition, you will find the following typographic conventions
throughout this manual.
Safety Instructions
General Warning
Failure to follow safe installation guidelines can cause death or
serious injury. The voltages used in the product can cause
severe electric shock and/or burns, and could be
lethal.Extreme care is necessary at all times when working
with or adjacent to it. The installation must comply with all
relevant safety legislation in the country of use.
Qualified Person
For the purpose of this manual and product, a “qualified
person” is one who is familiar with the installation,
construction and operation of the equipment and the hazards
This Represents
bold
Characters that you must type exactly as they appear. For
example, if you are directed to type a:setup, you should type
all the bold characters exactly as they are printed.
italic
Place holders for information you must provide. For example, if
you are directed to type filename, you should type the actual
name for a file instead of the word shown in italic type.
ALL CAPITALS Directory names, file names, key names, and acronyms.
SMALL CAPS Non-printable ASCII control characters.
KEY1+KEY2
example: (Alt+F)
A plus sign (+) between key names means to press and hold
down the first key while you press the second key.
KEY1,KEY2
example: (Alt,F)
A comma (,) between key names means to press and release the
keys one after the other.
vii
involved. In addition, this individual has the following
qualifications:
•Is trained and authorized to energize, de-energize, clear,
ground and tag circuits and equipment in accordance with
established safety practices.
•Is trained in the proper care and use of protective
equipment in accordance with established safety practices.
•Is trained in rendering first aid.
Warning
For the purpose of this manual and product, “Warning”
indicates death, severe personal injury or substantial
damage CAN result if proper precautions are not taken.
Caution
For the purpose of this manual and product, “Caution”
indicates minor personal injury or property damage CAN
result if proper precautions are not taken.
Note
For the purpose of this manual and product, “Note”
indicates information about the product or the respective
part of the manual which is essential to highlight.
Epsilon Only
For the purpose of this manual and product, the “Epsilon”
symbol indicates information about the Epsilon drive
specifically.
viii
ALP-130 and ALP-430 Auxiliary Logic Power Supply Installation Manual
E Series Only
E
N
For the purpose of this manual and product, the “EN”
symbol indicates information about the E Series drive
specifically.
Throughout this manual, the word "drive" refers to an Epsilon
or E Series drive.
ix
Underwriters Laboratories Listed
The ALP-130/-430 are marked with the “UL Listed” label after
passing a rigorous set of design and testing criteria developed
by UL (UL508C). This label indicates that the UL certifies this
product to be safe when installed according to the installation
guidelines and used within the product specifications.
The “conditions of acceptability” required by UL are:
•The ALP-130 ambient temperature must be 40° C (104° F)
or less.
•The ALP-430 ambient temperature must be 50° C (122° F)
or less.
CE Declaration of Conformity
The ALP-130/-430 (Auxiliary Logic Supply) is marked with the
“Conformite Europeenne Mark” (CE mark) after passing a
rigorous set of design and testing criteria. This label indicates
that this product meets safety standards when installed
according to the installation guidelines and used within the
product specifications.
LISTED 80XM
IND. CONT. EQ.
A
L
P
-
1
3
0
a
n
d
A
L
P
-
4
3
0
x
ALP-130 and ALP-430 Installation Manual
Declaration of Conformity
Manufacturer’s Name: EMERSON Motion Control
Manufacturer’s Address: 1365 Park Road
Chanhassen, MN 55317
USA
Declares that the following products:
Products Description: Drive Accessories
Model Number: RSR-2 and ALP-430
Conforms to the following product specification:
The products herewith comply with the requirements of the Low Voltage Directive (LVD) 73/23/EEC. These products are considered
components and as such, the EMC Directive (89/336/EEC) does not apply.
Supplementary information:
This electronic drive product is intended to be used with an appropriate motor, electrical protection components and other equipment to
form a complete end product or system. It must only be installed by a professional assembler who is familiar with requirements for safety
and electromagnetic compatibility (“EMC”). The assembler is responsible for ensuring that the end product or system complies with all the
relevant laws in the country where it is to be used. Refer to the product manual for installation guidelines.
August 18, 1999
Bradley Schwartz/ VP Engineering Date
European Contact: Sobetra Automation
Langeveldpark Lot 10
P. Dasterleusstraat 2
1600 St. Pieters Leeuw, Belgium
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Fuente de alimentación de Emerson
Emerson
Emerson NetSure 501 A50 Manual de usuario
Emerson
Emerson GIE 4820/3A/3.45KW Manual de usuario
Emerson
Emerson Liebert Challenger 3000 Manual de usuario
Emerson
Emerson Liebert NXL 250 Manual de usuario
Emerson
Emerson SMP Series Manual de usuario
Emerson
Emerson ASTEC Helios Candeo AP6C75AA Manual de usuario
Emerson
Emerson netsure 9500 Manual de usuario
Emerson
Emerson NetSure 721NPBB Guía del usuario
Emerson
Emerson Rosemount 700XA Hoja de instrucciones
Emerson
Emerson Lorain CIP 4890 AP6C55CB Manual de usuario
Emerson
Emerson Liebert Npower 30-130 kVA Manual de usuario
Emerson
Emerson PACSystems RX3i Manual de usuario
Emerson
Emerson NetSure-48 VDC Power System Manual de usuario
Emerson
Emerson Series 600 Manual de usuario
Emerson
Emerson Metro MPS-4009 Guía de configuración
Emerson
Emerson NetSur 721NPBB Manual de usuario
Emerson
Emerson NetSure 501 A50 Manual de usuario
Emerson
Emerson ControlWave GFC Manual de usuario
Emerson
Emerson NetSure 710NPBA Manual de usuario
Emerson
Emerson DCX S Manual de usuario
