Emerson Rosemount 9195 Manual de usuario
Quick Start Guide
00825-0100-4488, Rev AA
November2023
Rosemount™ 9195 Wedge Meter
Assembly
NOTICE
This document provides basic installation guidelines for the Rosemount 9195 Wedge Meter
Assembly. For comprehensive instructions for detailed configuration, diagnostics,
maintenance, service, installation, or troubleshooting refer to the Rosemount 9195 Reference
Manual. The manual and this guide are also available electronically on Emerson.com/
Rosemount.
If the Rosemount 9195 Primary Element was ordered assembled to a Rosemount Pressure
Transmitter or a Rosemount 1199 Diaphragm Seal System, refer to the following Quick Start
Guides for information on configuration and hazardous locations certifications:
•Rosemount 3051S Quick Start Guide
•Rosemount 3051SMV Quick Start Guide
•Rosemount 4088 Quick Start Guide
•Rosemount 1199 Diaphragm Seal Quick Start Guide
•Rosemount 3051SAL Quick Start Guide
Hazardous Area Approvals for assemble-to flow meter components specified on distinct lines:
An assembly may be composed of certified pieces of equipment. The overall assembly is
subject to inspection by the authority having jurisdiction over the installation.
If the meter was ordered with a wireless transmitter, the battery will be shipped separately
due to freight carrier regulations.
WARNING
Process leaks may cause harm or result in death.
To avoid process leaks, only use gaskets and O-rings designed for the corresponding flange
to seal process connections.
Transmitter electronics maintenance should not be conducted on energized equipment
in a hazardous atmosphere.
Failure to comply with the requirements for intrinsic safety in a hazardous atmosphere could
result in an explosion.
If the process fluid is hazardous, the procedure outlined here should be modified as
required.
Failure to do so could result in serious injury to personnel or death.
If the line is pressurized, always open valves slowly.
Failure to do so could result in serious injury to personnel or death.
During installation never lift the meter by remote seal capillaries, the transmitter, RTD,
or impulse lines/valves.
Doing so may result in either meter damage or serious injury.
Quick Start Guide November2023
2 Emerson.com/Rosemount
WARNING
Physical access
Unauthorized personnel may potentially cause significant damage to and/or
misconfiguration of end users’ equipment. This could be intentional or unintentional and
needs to be protected against.
Physical security is an important part of any security program and fundamental to protecting
your system. Restrict physical access by unauthorized personnel to protect end users’ assets.
This is true for all systems used within the facility.
Contents
Before you begin..........................................................................................................................5
Locate the installation point....................................................................................................... 8
Orient the primary element......................................................................................................11
Install the primary element...................................................................................................... 20
Preparing for operation............................................................................................................ 23
Product certifications................................................................................................................ 26
November2023 Quick Start Guide
Quick Start Guide 3
Quick Start Guide November2023
4 Emerson.com/Rosemount
1 Before you begin
Before you begin the installation, consider the vibration and
temperature limits of the meter. Refer to the Rosemount 9195 Wedge
Meter Product Data Sheet, flow sizing, or instrument tag for functional
limits.
Figure 1-1: Exploded View 1: Compact Remote Seal (WSP Style)
A. Wedge Primary Element Meter Body
B. Mounting Bracket Studs
C. Mounting Bracket Screws
D. Remote Seal Gaskets
E. Transmitter
F. Remote Seals
G. Remote Seal Screws
H. Mounting Bracket Nuts
I. Mounting Bracket Washers
J. Mounting Bracket
K. Mounting Bracket Lock Washers
November2023 Quick Start Guide
Quick Start Guide 5
Figure 1-2: Exploded View 2: 2" NPS/DN50 Flanged Assembly
A. Wedge Primary Element Meter Body
B. Mounting Bracket Screws
C. Mounting Bracket Lock Washers
D. Transmitter
E. Mounting Bracket Washers
F. Mounting Bracket Nuts
G. Mounting Bracket
H. Remote Seal Nuts
I. Flushing Ring Plugs
J. Remote Seals
K. Flushing Ring
L. Remote Seal Gaskets
M. Remote Seal Studs
Note
If using primary isolation valves (option codes BV1 and GV1 in the
model number), valves and valve gaskets are installed between the
branch gasket (L) and the flushing ring or remote seal (K or J). Ensure
a gasket is used between all connection points.
Quick Start Guide November2023
6 Emerson.com/Rosemount
Figure 1-3: Exploded View 3: ½-inch NPT Tubed Assembly
A. Wedge Primary Element Meter Body
B. Manifold
C. Transmitter
D. Mounting Lock Washers
E. Mounting Screws
F. Formed Tubing
G. Compression Fittings
November2023 Quick Start Guide
Quick Start Guide 7
2 Locate the installation point
Locate the primary element installation point. If possible, install the
meter at ground level to allow meter access.
Table 2-1: Straight Pipe Requirements (Distance in Number of
Pipe Diameters)
Type of flow
disturbance
upstream of
flow meter(1)
Typical straight
run pipe
diameters (D)
Straight run
pipe diameters
per ISO(2)(3)
Upstream (inlet)
side of primary
Single 90° bend
in the same plane
10 7
Three 90° bends
with parallel exit
and outlet
22 22
Two or more
90° bends in the
same plane
15 21
Concentric
expander
(D/2 to D)
7 7
Concentric
reducer
(3D/2 to D)
7 7
Partially closed
valve
10 15
Pipe tee –
straight run
5 7
Pipe tee –
used as elbow or
tee
6 8
Downstream (outlet) side of primary
(all disturbances)
5 6
(1) Consult an Emerson representative if a disturbance is not listed.
(2) Upstream straight pipe run diameters are measured from the upstream
pressure taps of the Rosemount 9195 primary element. Downstream
straight pipe run diameters are measured from the downstream
pressure taps.
(3) Straight pipe requirements are based on ISO 5167-6 for wedge ratios 0.2
≤ h/D ≤ 0 .6.
Quick Start Guide November2023
8 Emerson.com/Rosemount
2.1 Reversing the transmitter
The Rosemount 9195 primary element with factory installed tubing
defaults to a left-handed orientation. If a right-handed meter
orientation is required, this can be specified in the model code.
If there is interference in the mounting location, the transmitter
electronics can be reinstalled on the opposite side of the meter by
following the directions below.
Note
This is only applicable to the Direct mount ½" NPT connection style,
option code "T" in the model number.
WARNING
This operation should not be conducted on either energized
equipment or in a hazardous atmosphere.
Always depressurize the system before disassembling the
compression fitting.
Failure to comply with the requirements for intrinsic safety in a
hazardous atmosphere could result in an explosion.
Procedure
1. Mark the tube at the edge of the compression nut. Later,
use these marks to ensure the tubing is fully seated in the
compression fitting.
Disassemble the compression fitting nuts at the tubing-to-
manifold connections.
2. Remove the bolts connecting the manifold to the mounting
bracket.
3. Remove the manifold from the mounting bracket.
4. Remove the transmitter from the manifold.
5. Rotate the transmitter 180º on the manifold, ensuring the high
and low pressure ports match those on the Rosemount 9195
meter body.
Tighten the bolts as shown in Table 2-2.
6. Position the tubing into the compression fittings on the
manifold on the desired side of the mounting bracket,
ensuring the high and low pressure sides of the transmitter
match that of the wedge primary element.
7. Install the manifold onto the mounting bracket loosely.
November2023 Quick Start Guide
Quick Start Guide 9
8. Tighten the compression fitting nuts to 1.25 turns past hand-
tight.
a) Insert the tube with preswaged ferrules into the fitting
until the front ferrule seats against the fitting body.
Note
If needed, lightly reapply lubricant to the body threads
and the rear surface of the back ferrule.
b) While holding the fitting body steady, rotate the nut
with a wrench to the previously pulled-up position, as
indicated by the marks on the tube and flats.
At this point, you will feel a significant increase in
resistance.
c) Slightly tighten the nut.
9. Finish tightening the manifold onto the mounting bracket.
10. Verify the flange bolts are protruding through the sensor
module before applying pressure.
Table 2-2: Torque Values for Transmitter Mounting Bolts
Bolt material Head
markings
Initial torque Final torque
Carbon steel
(CS)
B7M 300 in-lb 650 in-lb
Stainless steel
(SST)
150 in-lb 300 in-lb
Quick Start Guide November2023
10 Emerson.com/Rosemount
Tabla de contenidos
Otros manuales de Instrumento de medición de Emerson
Emerson
Emerson Penberthy Multiview Manual
Emerson
Emerson Daniel 3410 Series Manual de usuario
Emerson
Emerson Rosemount 8742C Manual de usuario
Emerson
Emerson FB1100 Manual de usuario
Emerson
Emerson Rosemount 8600D Series Manual de usuario
Emerson
Emerson Mobrey Hydratect 2462 Manual de usuario
Emerson
Emerson FB1100 Manual de lista de piezas
Emerson
Emerson Daniel 3410 Series Manual de programación
Emerson
Emerson Sensi Predict Manual de usuario
Emerson
Emerson Rosemount X-Stream Series Manual de usuario
Emerson
Emerson Fisher 4320 Manual de usuario
Emerson
Emerson Rosemount 54eA Manual de usuario
Emerson
Emerson Rosemount 8750WB Manual de usuario
Emerson
Emerson FloBoss 107 Manual de usuario
Emerson
Emerson Rosemount 8800D Series Guía del usuario
Emerson
Emerson Rosemount 5400 Series Manual de usuario
Emerson
Emerson FloBoss S600+ Manual de instalación y operación
Emerson
Emerson Rosemount 3051 Manual de usuario
Emerson
Emerson Rosemount CT5800 Manual de usuario
Emerson
Emerson NGA2000 TO2 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario