Emerson A6312 Manual de usuario

Quick Start Guide

MHM-97448

NC: 6540-90025

Rev.: 1.032

CSI 6500 Machinery Health™Monitor

A6312, Dual Channel Speed/ Key Monitor

Emerson Process Management

Machinery Health Management

835 Innovation Drive

Knoxville, TN 37932 USA

T 1(865) 675-2400

F 1(865) 218-1401

www.EmersonProcess.com

The contents of this publication are presented for informational purposes only, and while every effort has

been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express

or implied, regarding the products or services described herein or their use or applicability. All sales are

governed by our terms and conditions, which are available on request.We reserve the right to modify or

improve the designs or specifications of our products at any time without notice.

companies. The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are

the property of their respective owners.

GB Explanation of symbols

If this symbol is printed on a device, according to IEC 61010 it means that the

documentation of the device must be completely read and understood before

installation and commissioning of the device. All safety−related instructions

of this document must be observed. These safety−related instructions are

marked by the “STOP” symbol in this document.

If this symbol is printed on a device, according to IEC 61010 it means that this

device must be operated with DC voltage.

iThis symbol identifies text that contains important information.

!Not following instructions identified with this symbol can result in functional

issues and incorrect measurements without damaging the machine.

STOP

Safety and warning instructions are identified with this symbol.

Failure to observe these instructions can result in material damage or

personal injury.

DSymbolerklärung

Ist dieses Symbol auf einem Gerät angebracht, so sagt dies nach IEC 61010

aus, das es zur Installation und Inbetriebnahme des Gerätes zwingend

erforderlich ist, die Dokumentation des Gerätes vollständig gelesen und

verstanden zu haben. Sicherheitsrelevante Hinweise in dieser

Dokumentation sind unweigerlich zu beachten und im weiteren Verlauf dieser

Dokumentation durch das “STOP” Symbol (siehe unten) gekennzeichnet.

Ist dieses Symbol auf einem Gerät angebracht, so sagt dies nach IEC 61010

aus, dass es mit Gleichspannung betrieben wird.

iDieses Symbol kennzeichnet Textstellen, die wichtige Informationen

enthalten.

!Hinweise, die bei Nichtbeachtung zu Funktionsstörungen und

Fehlmessungen führen, ohne das Gerät zu beschädigen, sind mit diesem

Symbol gekennzeichnet.

STOP

Sicherheits- und Warnhinweise sind mit diesem Symbol gekennzeichnet.

Die Nichtbeachtung solcher Hinweise kann zu Sachbeschädigungen oder

Personenschäden führen.

Product Service Centers

America

Emerson Process Management

835 Innovation Drive

Knoxville, TN 37932

Tel: 865−675−2110

Fax: 865−218−1401

Brazil

Emerson Process Management Ltd.

Av Hollingsworth 325

Sorocaba, SP

BRAZIL 18087−000

Phone: 55 15 2383788

Fax: 55 15 22823300

Europe, Middle East, Africa

Emerson Process Management

div. ESAD

MHM Repair Center

Piestanska 1202/44

915 28 Nove Mesto nad Vahom

Slowakia

Tel: +421/32/7700 538

Fax: +421/32/7700 884

Asia

Emerson Process Management / Asia

Pacific Private Ltd.

3904 Room Central Plaza

18 Harbour Road Wan−Chai

Hong Kong

Tel: 852−2802−9223

Fax: 852−2802−8227

Incoming goods inspection

Check the content of the shipment to ensure that it is

complete; visibly inspect the goods to determine if the

device may possibly have been damaged during

transport. The following parts are included in the scope

of delivery and must be contained in the shipment.

1. A6312

2. Product information

If the contents are incomplete, or if any defects are

observed, a complaint must be filed with the carrier

immediately. Moreover, the responsible Emerson sales

organization must be informed to enable repair or

replacement of the device. Repairs or calibration that

may be required, are only possible at the Emerson

factory.

In this case, a non−detachable tag with customer name,

defect observed and version of the A6910 configuration

software must be attached to the device.

Repair and maintenance

During operation, monitors do not require any mainte-

nance.

Repair or calibration of monitors is only possible at

Emerson.

iThe additional PCB (controller board)

is calibrated with the main board and

must not be replaced.

If work with the opened device on−site is

unavoidable, this should only be performed by a

specialist who is familiar with the associated

hazards.

STOP

Capacitors in the device can still be

energized, even if the device has

been disconnected from all power

sources.

If repair or recalibration of a monitor is required, it

must be sent to Emerson. Attach a non−detachable

tag to the monitor with customer name, defect

observed and version of the A6910 configuration

software.

Guidelines for Returning Equipment to the

Product Service Center

If repair or calibration of a monitor is required, it must

be sent to Emerson.

Occasionally, concerns with CSI technology

hardware could arise. Should this happen, customers

under warranty or a current support agreement are

entitled to no−charge repairs.

Follow the checklist below to minimize return time

and ensure proper processing of your equipment.

Before returning any equipment to a Product Support

Center, please review this information:

1. Obtain a Return Materials Authorization (RMA)

number and the address of the appropriate

Product Service Center by calling 865.675.4274*.

Listen to the options for receiving an RMA. You

will be routed to support personnel who will

document your concern and give you an RMA

number if you are under support or warranty. If

your hardware is not under support or warranty,

you must have a Purchase Order for the amount

of the repair service before you can receive an

RMA number. Pricing for your repair can be

obtained from support personnel or by calling

your local sales representative. Once you have

your purchase order, call 865.675.4274* for an

RMA.

2. Once you have received your RMA, send your

hardware to the appropriate product service

center. Your hardware package should include:

GRMA Number (plus Purchase Order if

applicable)

GDescription of the hardware

problem

GReturn shipping address including a

phone number (No P.O. boxes).

GAny special request regarding the

return shipment.

GA list of the model numbers of each

item(s) being returned, along with

the serial number.

GYour name, address, telephone

number and email address.

GCompany Name.

A form for completing this information has

been provided.

Make a copy of the form, complete all lines,

and return a copy in each return shipment.

Out of warranty? Need to get under

support? Get a customized quote for

bringing all your CSI technologies under a

support agreement:

Phone: 865.675.2400*, ext. 2130

Fax: 865.218.1478*

Email:

mhm.supportagreement@emersonproces

s.com

*Customers outside the Americas and

Canada: please refer to the list of service

centers and contact the service center near

you.

All rights are strictly reserved

Reproduction or divulgation in any form

whatsoever is not permitted without written

authority from the copyright owner.

RMA Required Information

RMA number issued by Product

Service Center:

For all items beingreturned, please

list Model / Serial Number:

Are you under warranty or a current

support agreement (circle one)?

Yes No

If you answered no, what is your

purchase order number?

Company Name:

Contact Name:

Contact Address:

Contact Phone:

Contact Fax:

Contact Email:

Please describe the problem you are experiencing:

If we are to send the return shipment to someone other than the

Contact Name/Address above, please provide that address here,

including Contact Name and Phone Number:

Are there any special instructions regarding the return?

Please provide invoice address (if a purchase order was required):

Support customers −your instrument is shipped back to you the same

way that it is sent to our service center. For example, if you ship via

ground transportation, it is shipped back via ground.

Page/Seite 7

Product Information / Produktinformation A6312

1GB Rotational Speed Monitor 8......................

1.1 Scope of Delivery 8...........................................

1.2 CSA Certification 9...........................................

1.3 CSA −Conditions of acceptability 9............................

1.4 Advice for Installation 9.......................................

1.5 Installation and Mounting 9...................................

1.6 Technical data 11..............................................

1.6.1 Signal conditioning 11.......................................................

1.6.2 Channel monitoring 13......................................................

1.6.3 Function outputs and alarms 15..............................................

1.6.4 Communication interfaces 16.................................................

1.6.5 Power supply 17............................................................

1.6.6 Environmental conditions 18.................................................

1.6.7 Mechanical structure 18.....................................................

2DDrehzahl−/ Key−Monitor 19.......................

2.1 Lieferumfang 19...............................................

2.2 CSA Zertifizierung 20..........................................

2.3 CSA −Akzeptanzkriterien 20....................................

2.4 Hinweis zur Installation 21......................................

2.5 Installation und Montage 21....................................

2.6 Technische Daten 23...........................................

2.6.1 Signalkonditionierung 23.....................................................

2.6.2 Kanalüberwachung 25.......................................................

2.6.3 Funktionsausgänge und Alarme 27............................................

2.6.4 Kommunikationsschnittstellen 28.............................................

2.6.5 Spannungsversorgung 29....................................................

2.6.6 Umgebungsbedingungen 30..................................................

2.6.7 Mechanischer Aufbau 30....................................................

3 Connection Diagrams and Figures /

Anschlusspläne und Abbildungen 31....................

4 PI Revision List 36.....................................

Page 8

Product Information / Produktinformation A6312

Rotational Speed Monitor

1GB ROTATIONAL SPEED MONITOR

!This product Information contains general information about the dual channel

speed/ key monitor types A6312/06 & A6312/08. If not stated otherwise, all

information denoted by A6312 is valid for both types, listed before.

The two−channel rotational speed monitor A6312 is a module of the A6000 machine monitoring

system. The micro−processor controlled monitor is used in conjunction with two eddy current

measuring chains or hall−effect sensors (e.g. PR 9376) and in combination with triggering

wheels to measure and conditioning of shaft speeds and rotational reference marks

(key−pulses).

Both channels may be used separately used to measure:

•2 speeds from 2 shafts

•2 key−pulses from 2 shafts each with a triggermark (with phase relation)

Both channels may also be used in combination with each other:

•to detect the direction of rotation of one shaft

•to detect a difference between two shaft speeds

In this product information the mounting and electrical connection of the

monitor is described.

For secure use of the monitor, observe the direction for use “Rotational Speed

Monitor A6312” (order number: 6110−90025). You can find this direction on

the configuration software CD as pdf−data file. Amongst others, it contains

useful informations for configuration and use of the A6312.

To ensure the safe operation of the monitor and to permit setting of all

functions, it is indispensable to use only the latest versions of configuration

software (version 2.05 or newer) and operating manual.

The use of old operating manuals or configuration programs out of date may

lead to malfunctions or limitations of the measuring functions.

1.1 Scope of Delivery

The following parts are included in the scope of delivery and must be contained in the shipment:

•Rotational Speed Monitor A6312

•This product information

Accessories (not included in delivery):

•MMS ParaKit (order no.: 9510−00027)

If the contents are incomplete or if is there any damage, so directly complain at the bearer. The

competent epro−sales agency must be also informed, to enable repair or replacement for the

monitor. Repair or calibration of this instrument may only be done at epro.

Page 9

Product Information / Produktinformation A6312

Rotational Speed Monitor

1.2 CSA Certification

STOP

For valid CSA certification, all devices (IMR 6000/xx and A6000 modules)

must be marked with the respective CSA lable.

If no CSA lable is available on the respective device, this device is not CSA

certified!

The respective CSA lable looks as shown in the following picture.

1.3 CSA −Conditions of acceptability

This device must be supplied with safety low voltage SELV LPS (C22.2 60950−1) 24V. The

voltage required for operation must be drawn from a separate power supply.

The IMR system should be placed in a suitable fire enclosure.

The IMR system is evaluated for an ambient of 0°C to 45°C.

Adequate ventilation space has to be provided so that heat does not build up. The ventilation

space must be at least 1 RU (13/4 inch) in all directions. If the ambient temperature of the rack

rises above 45 °C, cool this instrument with a forced air fan, cooler, or similar.

When mounting several IMR units above each other in one cabinet, install cooling fan racks in

between instead of the ventilation space. The necessary specifications for cooling fan racks

result from the environmental and sitting criterions of the cabinet and thus cannot be defined

generally.

1.4 Advice for Installation

STOP

According to the IEC 61010 directive, permanently installed systems must be

equipped with a power disconnect device (e.g. a switch or circuit−breaker

according to IEC60947−1 and IEC60947−3). When using an IMR rack, in

compliance with this directive, such a switch or breaker must be implemented

into the cabinet installation and easily accessible for the user. Furthermore,

each disconnect devices must be labeled in accordance to the associated

system.

1.5 Installation and Mounting

A prepared 3U slot in a 19” rack, or other Intermas−compatible enclosure, is required for

mounting the A6312 monitor. The slot must be fitted with a 48−pin plug connector (DIN 41612,

design F 48 M). The pin assignment is listed in the following table.

Page 10

Product Information / Produktinformation A6312

Rotational Speed Monitor

d b z

2UN+ (+24V) U−(0V/Common) UB+ (+24V, redundant) 2

4A (RS 485) GND (BP, Common, RS 485) B (RS 485) 4

6Supply2+ (sensor) Supply1−(sensor) Supply1+ (sensor) 6

8AIN2−(Input) Supply2−(sensor) AIN1−(Input) 8

10 AIN2+ (Input) GND AIN1+ (Input) 10

12 PU1 (24V−pull up pulse1) GND NC (MMS6310) / Test1 (MMS6312) 12

14 Pulse1−C (collector) Pulse1−E (emitter) Pulse1−TTL 14

16 Pulse2−C (collector) Pulse2−E (emitter) Pulse2−TTL 16

18 PU 2(24V−pull up pulse2) I1−(current output common) I1+ (current output CH1) 18

20 Reset peak value 1 I2−(current output common) I2+ (current output CH2) 20

22 NC (MMS6310) / Test2 (MMS6312) GND ES (external lock) 22

24 SC−A (oper. principle GW2) GND SC−D (oper. principle GW1) 24

26 GW1−D−C (danger1 collector) GW1−A−C (alert1 collector) CC1−C (ch. clear1 collector) 26

28 GW1−D−E (danger1 emitter) GW1−A−E (alert1 emitter) CC1−E (ch. clear1 emitter) 28

30 GW2−D−C (danger2 collector) GW2−A−C (alert2 collector) CC2−C (ch. clear2 collector) 30

32 GW2−D−E (danger2 emitter) GW2−A−E (alert2 emitter) CC2−E (ch. clear2 emitter) 32

Jumper RS 485

RS 485 bus operation requires an electrical terminator on the first and last bus device.

This is done with plug−in jumpers, that are on the controller board. The figure shows the position

of the jumpers.

To activate the bus terminator and to place lines “A” and “B” on the references, plug the jumpers

as shown in Fig. b). Fig. a) shows the jumper position for deactivated bus termination and open

references (delivery status).

•Plug−in jumper 1−2 closed: Bus line “B” via pull−down resistor on ground

•Plug−in jumper 3−4 closed: 120 ΩResistor between “A” and “B”

•Plug−in jumper 5−6 closed: Bus line “A” via pull−up resistor on +5 V

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de Emerson

Emerson

Emerson Rosemount 8732 Manual de usuario

Emerson

Emerson Rosemount 8750W Manual de usuario

Emerson

Emerson Daniel PT Series Manual de usuario

Emerson

Emerson Daniel 3812 Manual de usuario

Emerson

Emerson Rosemount 6888Xi Manual de usuario

Emerson

Emerson Rosemount 2410 Manual de usuario

Emerson

Emerson Rosemount 370XA Manual de usuario

Emerson

Emerson Daniel Ultrasonic 3410 Series Manual de usuario

Emerson

Emerson AMS Manual de usuario

Emerson

Emerson Micro Motion Manual de usuario

Emerson

Emerson Rosemount 1054B Manual de usuario

Emerson

Emerson Rosemount 1195 Manual de usuario

Emerson

Emerson Rosemount 8732EM Manual de usuario

Emerson

Emerson TopWorx 4310 Manual de usuario

Emerson

Emerson Rosemount 753R Manual de usuario

Emerson

Emerson Rosemount 2410 Manual de usuario

Emerson

Emerson Rosemount 485 Annubar Manual de usuario

Emerson

Emerson Rosemount 3814 Manual de usuario

Emerson

Emerson Sensi Predict Manual de usuario

Emerson

Emerson FB2100 Manual de usuario

Emerson

Emerson Rosemount CT5100 Manual de usuario

Emerson

Emerson Penberthy Manual

Emerson

Emerson FB1100 Manual de lista de piezas

Emerson

Emerson Rosemount 3051S Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario