Emerson Rosemount 2410 Manual de usuario

Manual Supplement

00809-0400-2410, Rev AA

March 2016

Rosemount™2410 Tank Hub

Enraf®emulation instruction

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1

Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5

Configuration using the FBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7

Configuration using the EBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 14

Advanced information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page23

1.1 Introduction

The purpose of this document is to provide guidelines on how to change from Enraf to

Rosemount equipment by exchanging gauges. When an Enraf gauge is replaced with a

Rosemount gauge, it is necessary to configure the Rosemount 2410 Tank Hub for emulation.

The Rosemount field devices, for example Rosemount 5900 Radar Level Gauge and Rosemount

2240S Temperature Transmitter, are connected to the tank hub using the intrinsically safe

Tankbus as usual. Emulation is done in the tank hub only. Each tank hub can emulate up to 10

tanks (10 separate Enraf gauges).

Figure 1-1. Rosemount Devices Replacing Old Gauges in an Existing Enraf System

Entis

PLC

CIU

Rosemount

5900S Radar

Level Gauge Rosemount 2410

Tank Hub

Rosemount 3051S

Pressure Transmitter

Rosemount 2240S

Temperature Transmitter

with sensor

Manual Supplement

00809-0400-2410, Rev AA

Rosemount 2410 Tank Hub

March 2016

Rosemount 2410 Tank Hub

1.1.1 Enraf system characteristics

A typical Enraf tank gauging system consists of a number or field devices such as level,

temperature and pressure devices. These devices are connected to a host computer via a

Communication Interface Unit (CIU).

Different versions of the CIU:

CIU 858

CIU 880 Prime

CIU 880 Plus

The host computer can either be a PC with Entis monitoring system, or an Enraf Microlect

station.

The Rosemount 2410 Tank Hub supports the Enraf GPU protocol. It can therefore be

connected directly to Entis/CIU systems using the GPU protocol.

Enraf GPU communication parameters

Start bits: 1

Data bits: 7 (ASCII)

Parity: Odd

Stop bits: 1

Baud rate: Selectable 1200 (default)/2400

Enraf gauges for emulation

The Rosemount 2410 can emulate Enraf gauges with Type of Instrument (TOI), B or C.

Table 1-1. Typical Enraf Devices

TOI Devices with GPU protocol

B811, 854, 894, 873, 973

C813 MTG

Manual Supplement

00809-0400-2410, Rev AA

Rosemount 2410 Tank Hub

March 2016

Rosemount 2410 Tank Hub

1.1.2 Rosemount 2410 Tank Hub communication

The tank hub has slots for two independent communication boards, primary and secondary

field bus, for TRL2 Modbus®, RS485 Modbus, emulation or wireless communication.

Primary and secondary field bus

A tank hub equipped with both primary (TRL2 Modbus) and secondary (Enraf GPU) field bus,

can be configured for Enraf emulation using the Rosemount 2180 Field Bus Modem (FBM) as

usual. Since the tank hub simultaneously communicates on both ports, the TankMaster™PC

can in addition to configuration also be used to monitor the devices in operation, during

Enraf emulation. Section “Configuration using the FBM” on page 7 describes configuration

of the tank hub with the FBM.

For a tank hub equipped with only a primary field bus, the Rosemount 3180 Enraf Field Bus

Modem (EBM) will be used to configure the tank hub for Enraf emulation. Configuration is

done using the TRL2 Modbus protocol. When configuration is completed, the field bus will

be connected to the CIU for operation and the protocol will be switched to Enraf GPU. See

“Configuration using the EBM” on page 14 for instructions on how to configure the tank

hub using the EBM.

Figure 1-2. Tank Hub Communication Board for Enraf Emulation

Tank hub with one

communication board

Tank hub with two

communication boards

EBM

FBM

CIU CIU

TankMaster

WinSetup PC

TankMaster PC Entis PC Entis PC

Primary bus:

TRL2 Modbus

Primary bus:

TRL2 Modbus

Secondary bus:

Enraf GPU Primary bus:

Enraf GPU

Manual Supplement

00809-0400-2410, Rev AA

Rosemount 2410 Tank Hub

March 2016

Rosemount 2410 Tank Hub

Wireless communication

The tank hub supports Emerson™’s wireless technology, which is based on WirelessHART®,

the emerging industry standard for wireless field networks. The Emerson Smart Wireless

THUM™Adapter acts as a wireless data link between the tank hub and a Smart Wireless

Gateway.

The tank hub can simultaneously combine wireless and Enraf communication. The primary

field bus communicates via Enraf GPU and the secondary field bus via WirelessHART.

With this tank hub communication configuration, control room redundancy is achieved.

Figure 1-3. Tank Hub with Enraf and Wireless Communication

Tank hub with two

communication boards

CIU

TankMaster PC

Entis PC

Primary bus:

Enraf GPU

Secondary bus:

WirelessHART

Smart Wireless

THUM Adapter

Smart Wireless

Gateway 1410/1420

Manual Supplement

00809-0400-2410, Rev AA

Rosemount 2410 Tank Hub

March 2016

Rosemount 2410 Tank Hub

1.2 Electrical installation

1.2.1 Rosemount 2410 Tank Hub connections

Figure 1-4. Terminal Block in the Explosion-Proof/Flameproof Compartment

Table 1-2. Terminal Assignment for Non-Intrinsically Safe Side

Terminal Designation Function

1N / - Power, Neutral / DC -

2L / + Power, Line / DC +

3K1 A Relay 1 output (optional). Hardware configurable NO/NC.

4K1 com Relay 1 common

5K2 A Relay 2 output (optional). Hardware configurable NO/NC.

6K2 com Relay 2 common

7a/7b P Bus B Primary communication bus B

8a/8b P Bus A Primary communication bus A

9S Pwr - Secondary bus power - (optional)

10 S Pwr + Secondary bus power +(optional)

11 S Bus B Secondary communication bus - (optional)

12 S Bus A Secondary communication bus + (optional)

PE PE Power supply protective ground

GND_1 GND_1 Housing chassis/shield Primary bus

GND_2 GND_2 Housing chassis/shield Secondary bus

Secondary field bus

Primary field bus

Manual Supplement

00809-0400-2410, Rev AA

Rosemount 2410 Tank Hub

March 2016

Rosemount 2410 Tank Hub

1.2.2 Enraf Field Bus Modem (EBM)

Figure 1-5. Enraf Field Bus Modem Connection

A. Field bus connector

B. Power connector

C. Communication status LED (flashing green)

D. Protocol switch(1):

Left position: Modbus

Right position: Normal (GPU)

E. Baud rate switch(2):

Left position: 2400

Right position: 1200

F. Connector for RS232 communication with the computer

1.2.3 How to connect the EBM

1. Connect the tank hub to the EBM(3).

2. Connect the EBM to the WinSetup computer.

3. Be sure the protocol switch is set to “Normal (GPU)” and the baud rate switch is set

to “1200”, see Figure 1-5 on page 6.

4. Supply the EBM with power.

5. Verify communication with the tank hub through the flashing green LED.

1.2.4 Baud rate

The Rosemount 2410 Tank Hub has a pre-configured baud rate (1200) that cannot be

changed by the software configuration. The baud rate is controlled by hardware switches on

the Enraf communication board. See “Change baud rate” on page 25 for information on

how to change the baud rate.

1. Select right position “Normal (GPU)” for Enraf emulation configuration.

2. Select right position “1200” for Enraf emulation configuration.

3. The cable to be connected to the field bus is delivered with the EBM.

Field Bus

Field Bus: Pin 4,6 Shield: Pin5

EBM 3180

PC-modem

MADE IN SWEDEN

Rosemount Tank Radar AB

Gothenburg, Sweden

External DC

Power Supply

8-12V, 60mA

Pos+ Neg-

Normal (GPU)

Modbus

(4800 baud)

1200 baud

2400 baud

Computer

RS 232

Tank Gauging

Back side view

Front side view

Manual Supplement

00809-0400-2410, Rev AA

Rosemount 2410 Tank Hub

March 2016

Rosemount 2410 Tank Hub

1.3 Configuration using the FBM

The Rosemount 2410 Tank Hub is configured by using the Rosemount TankMaster

WinSetup configuration program(1). WinSetup is a user-friendly software package that

includes basic configuration options as well as advanced configuration and service

functions.

A Tank hub with two communication boards is normally configured using an FBM(2). To

configure the tank hub for Enraf emulation, do the following:

1.3.1 Set up Modbus communication protocol

This section describes how to configure the Modbus Master protocol channel for

communication with the FBM. Specify PC communication port and the standard

communication parameters: Baud rate, Parity, and number of Stop Bits.

1. Open the Protocols folder in the Workspace window.

2. Select the Modbus Master icon.

3. Right click the proper MbMaster icon and select Properties to configure the

protocol channel.

4. Select the Communication tab.

1. See the Rosemount Tank Gauging System Configuration Manual (document number 00809-0300-5100) for more information on how

to use the TankMaster WinSetup software to configure the Rosemount 2410 Tank Hub.

2. A tank hub where the secondary field bus communicates via WirelessHART, can be configured by wireless communication with a Smart

Wireless Gateway.

Manual Supplement

00809-0400-2410, Rev AA

Rosemount 2410 Tank Hub

March 2016

Rosemount 2410 Tank Hub

5. Set the communication parameters:

6. Select the Enable Channel check box to activate the protocol channel.

7. Select OK to store the current configuration and close the configuration window.

1.3.2 Install Rosemount 2410 Tank Hub in WinSetup

The TankMaster WinSetup wizard is the recommended tool for installing the tank hub.

The installation wizard covers basic configuration of the tank hub.

Perform the following steps to start the installation wizard in TankMaster WinSetup:

1. In the Workspace window select the Device folder.

2. Right click and select Install New, or from the Service menu select the

Devices/Install New option. The Select Device window appears.

Port The COM port the FBM will connect to

Baud rate 4800

Stop bits 1

Parity None

Modem FBM 2180

Handshaking None

Reply timeout 1000 ms

Retries 3

Description Text describing the configured channel

Manual Supplement

00809-0400-2410, Rev AA

Rosemount 2410 Tank Hub

March 2016

Rosemount 2410 Tank Hub

3. From the Device Type drop-down list, select the 2410 Tank Hub option.

4. Type a name in the 2410 HUB Tag field.

The 2410 Hub Tag will be used as an identifier for the tank hub in various windows

and dialogs.

5. Select Next. The 2410 Tank Hub Communication window appears.

6. Make sure TankMaster communicates directly with the tank hub and that the

proper communication channel is chosen.

Manual Supplement

00809-0400-2410, Rev AA

Rosemount 2410 Tank Hub

March 2016

Rosemount 2410 Tank Hub

7. Default Modbus Address is 247 for the tank hub. It is recommended to change it to

an address 101-199. Do the following:

a. In the 2410 Tank Hub Communication window select Change Address on Device...

to open the Change Address window.

b. Enter the Unit ID and select the new Modbus Address.

When changing the device address, the Unit Id is used as a unique identifier of the

device. The Unit Id can be found on a label mounted on the device.

c. Select OK to confirm the address settings and close the Change Address window.

d. In the 2410 Tank Hub Communication window select Verify Communication to

check that communication is established between the TankMaster work station

and the tank hub. The Unit ID will appear when TankMaster finds the tank hub.

8. In the 2410 Tank Hub Communication window select Next to continue the

installation procedure of the tank hub.

9. Continue configuration as usual for a tank hub installation.

1.3.3 Configure specific variables for Enraf

1. In the Configuration tab, select Enraf Emulation.

Otros manuales para Rosemount 2410

Tabla de contenidos

Otros manuales de Equipos industriales de Emerson

Emerson

Emerson KlauKe mini+ EBS6LGKS Manual de usuario

Emerson

Emerson RIDGID MR-10 Manual de usuario

Emerson

Emerson SolaHD SCM-W-HRT7 Manual de usuario

Emerson

Emerson Machinery Health PR 9350 Manual de usuario

Emerson

Emerson Roxar 6000 ps Manual de usuario

Emerson

Emerson Leroy Somer DIGISTART D3 Manual de usuario

Emerson

Emerson Fisher ATST Desuperheater Manual de usuario

Emerson

Emerson Rosemount 3051S Series Manual de usuario

Emerson

Emerson YARWAY CT150 Series Manual

Emerson

Emerson GPC Series Instrucciones de instalación

Emerson

Emerson AS3-ACD Series Manual de usuario

Emerson

Emerson T124 Manual de usuario

Emerson

Emerson PACSystems RX3i Guía del usuario

Emerson

Emerson PACMotion VFD PROFINET Manual de usuario

Emerson

Emerson CC200 Manual de usuario

Emerson

Emerson Rosemount 5900C Manual de usuario

Emerson

Emerson 781 Manual de usuario

Emerson

Emerson SA1-2 Series Instrucciones de instalación

Emerson

Emerson FISHER Yarway AT-13/23 Instrucciones de funcionamiento

Emerson

Emerson CSB400 Series Instrucciones de montaje

Emerson

Emerson Lumity RTS Manual de usuario

Emerson

Emerson Liebert iCOM Manual de usuario

Emerson

Emerson Bettis RTS Manual de usuario

Emerson

Emerson ANDERSON GREENWOOD Manual de usuario

Manuales populares de Equipos industriales de otras marcas

ABB

ABB Unifix AD Manual

Mark 7

Mark 7 Evolution Manual de usuario

Husky

Husky HyPET Manual de usuario

bora

bora PM-1800 Manual de usuario

Grizzly

Grizzly T32428 Manual de usuario

Siemens

Siemens 8MF1 Series Manual de usuario

ABB

ABB HT610965 Manual de usuario

ABB

ABB SafeLink Manual de usuario

Phoenix

Phoenix PHX-150 Manual de usuario

ABB

ABB A165-L32 Manual de usuario

ABB

ABB HT842936 Manual de usuario

Rioned

Rioned UrbanJet Manual de usuario

Hermetica

Hermetica 10 Series Manual de usuario

HORNER

HORNER OEE Solution Manual de usuario

Hammerhead

Hammerhead HG375 Manual de usuario

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instrucciones de uso

ABB

ABB HT566657 Manual de usuario

Webasto

Webasto GSE CAN Manual de usuario