Emerson PACMotion VFD PROFINET Manual de usuario

PACMotion VFD PROFINET Configuration User Manual Contents

GFK-3226A Feb 2022

PACMotion VFD PROFINET Configuration

USER MANUAL

PACMotion VFD PROFINET Configuration User Manual Contents 
GFK-3226A Feb 2022 
 
 
Contents i 
 
 
Contents 
Section 1: Overview ...............................................................1 
1.1 Configuration Tools ............................................................................................. 2 
Section 2: PROFINET Configuration Steps ...............................3 
2.1 Simplex Configuration ......................................................................................... 3 
2.2 Hot Standby Redundancy .................................................................................. 10 
2.3 Media Redundancy Configuration...................................................................... 13 
Section 3: Commissioning using PACMotion VFD Studio ......16 
Section 4: Going Online with PME ........................................20 
4.1 Store the Configuration ..................................................................................... 20 
4.2 Run the Motor ................................................................................................... 21 
Section 5: Additional Information ........................................22 
General Contact Information ....................................................................................... 23 
Technical Support........................................................................................................ 23 
 

PACMotion VFD PROFINET Configuration User Manual Warnings and Cautions

GFK-3226A Feb 2022

Contents ii

Warnings and Caution Notes as Used in this Publication

WARNING

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other

conditions that could cause personal injury exist in this equipment or may be associated with its use.

In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used.

CAUTION

Caution notices are used where equipment might be damaged if care is not taken.

Note: Notes merely call attention to information that is especially significant to understanding and operating

the equipment.

These instructions do not purport to cover all details or variations in equipment, nor to provide for every possible

contingency to be met during installation, operation, and maintenance. The information is supplied for informational

purposes only, and Emerson makes no warranty as to the accuracy of the information included herein. Changes,

modifications, and/or improvements to equipment and specifications are made periodically and these changes may or

may not be reflected herein. It is understood that Emerson may make changes, modifications, or improvements to the

equipment referenced herein or to the document itself at any time. This document is intended for trained personnel

familiar with the Emerson products referenced herein.

Emerson may have patents or pending patent applications covering the subject matter in this document. The

furnishing of this document does not provide any license whatsoever to any of these patents.

Emerson provides the following document and the information included therein as-is and without warranty of any

kind, expressed or implied, including but not limited to any implied statutory warranty of merchantability or fitness for

a particular purpose.

PACMotion VFD PROFINET Configuration User Manual Section 1

GFK-3226A Feb 2022

Overview 1

Section 1: Overview

PACMotion Variable Frequency Drives (VFD) equipped with the PROFINET Interface Option Card are

capable of being installed on a PROFINET network. The redundancy capable version, IC866-OC-PR,

incorporates support for Hot Standby Redundancy and Media Redundancy. This user manual describes

the steps required to configure and communicate with a PACMotion VFD utilizing the IC866-OC-PR

over a PROFINET network. Another version of the option card, IC866-OC-P, is available with the same

features except without support for Hot Standby Redundancy.

In this user manual, we will utilize a CPL410 system to establish base PROFINET network

communications, enable Hot Standby Redundancy, and configure Media Redundancy.

The PLC controller will require a PROFINET Controller Device, either an embedded PNC such as those

incorporated into the CPL410 or CPE330, or a standalone PNC such as the PNC001.

This procedure assumes a CPL410 controller system and the PROFINET network has been connected.

Note: If Media Redundancy is required, the PROFINET network ring must be left open (i.e. one of the

network connections left disconnected) until the controllers and network devices are fully configured.

Figure 1: PACMotion VFD with CPL410 HSB and MRP

PACMotion VFD PROFINET Configuration User Manual Section 1

GFK-3226A Feb 2022

Overview 2

1.1 Configuration Tools

The following tools are required:

PAC Machine Edition (PME): Software used to configure the PACSystems Controller and associated I/O.

The VFDs are treated as I/O devices within the controller framework. PME is also used to develop PLC

logic that resides in the controller and to monitor the application. Refer to Section 2: PROFINET

Configuration Steps.

PROFINET DCP: This is a discovery tool launched from within PME. It is used for PROFINET networks

only. Refer to Section 2: PROFINET Configuration Steps.

PACMotion VFD Studio: This is also launched from within PME. It is used to perform PACMotion VFD

commissioning activities. Refer to Commissioning using PACMotion VFD Studio. Note that PME Release

9.50 SIM10 or later incorporates VFD Studio. USB to RS-485 adaptor (IC866-CABL-USB485) is required

for the VFD Studio tool to communicate with the drive.

1.2 Revisions in this Manual

Revision

Date

Description

Jul 2021

Initial Release

PACMotion VFD PROFINET Configuration User Manual Section 2

GFK-3226A Feb 2022

PROFINET Configuration Steps 3

Section 2: PROFINET Configuration Steps

2.1 Simplex Configuration

The following steps are required for a simple PROFINET connection.

1. Connect PME

Attach the computer running PAC Machine Edition (PME) to the PACSystems Controller to be

configured.

2. Configure the PROFINET Controller

On PME, select the hardware configuration for CPL410 and set LAN 2 Mode to PROFINET (Figure 2). For

additional details on programming a controller for a PROFINET network, refer to the GFK-2571,

PACSystems RX3i & RSTi-EP PROFINET I/O Controller User Manual.

Figure 2: Enable Embedded PROFINET Controller

PACMotion VFD PROFINET Configuration User Manual Section 2

GFK-3226A Feb 2022

PROFINET Configuration Steps 4

3. Assign the PNC Device Name and IP Address

Select the embedded PROFINET controller in the Navigator window to display the properties in the

Inspector window. In the Inspector window set the PNC Device name and IP address (Figure 3).

Figure 3: Assign Device Name and IP Address

PACMotion VFD PROFINET Configuration User Manual Section 2

GFK-3226A Feb 2022

PROFINET Configuration Steps 5

4. Add Drives to the Network

Once the supervising PROFINET controller has been set up, each associated drive may be set up as a

node on that network.

a) Right-click on the target PROFINET controller to bring up the pop-up menu and click on Add IO-

Device (Figure 4)

Figure 4: Add IO Device

b) From the PROFINET Device Catalog, expand the PACMotion VFD entry and select the model of the

drive to be networked at the current node (Figure 5). Select the IC866-OC-PR device.

Figure 5: PACMotion VFD Device Selection

PACMotion VFD PROFINET Configuration User Manual Section 2

GFK-3226A Feb 2022

PROFINET Configuration Steps 6

5. (Optional) If the specific PACMotion VFD model does not show up in the Device Catalog, access the

Emerson support website to download the corresponding PACMotion VFD GDSML file. (Links are

provided at the end of this document.) Then select Have GSDML, browse to the downloaded file,

and select Open. The imported GSDML will create a new device in the PROFINET Device Catalog.

a) Select the device corresponding to the current version of the GSDML file, then add that device

at the current node

b) Click OK to complete the device addition.

Important

Repeat until all drives have been attached to the network.

6. Connect to the PROFINET network

Establish an Ethernet connection between the host PC and the PROFINET network.

7. Launch the Discovery Tool

Under Utilities, launch the PROFINET DCP Tool (Figure 6).

Figure 6: Launch PROFINET DCP Tool

PACMotion VFD PROFINET Configuration User Manual Section 2

GFK-3226A Feb 2022

PROFINET Configuration Steps 7

8. Refresh the Device List

a) Verify the correct interface is selected in the Connection Settings window and change if necessary.

b) Click on the Refresh Device List button to generate a list of devices on that network (Figure 7).

Figure 7: List of Discovered Devices on PROFINET Network

c) Click on the row representing the drive to which a Device Name is to be assigned.

d) Assign a valid Device Name (Figure 8), then click on the Set Device Name button (Figure 8).

Figure 8: Set Device Name & (Optionally) IP Address

Tabla de contenidos

Otros manuales de Equipos industriales de Emerson

Emerson

Emerson PACMOTION VFD Instrucciones de instalación y funcionamiento

Emerson

Emerson PACEdge Manual de usuario

Emerson

Emerson CAD Instrucciones de instalación

Emerson

Emerson YARWAY 460D3 Series Manual de operación y mantenimiento

Emerson

Emerson Fisher 3024C Manual de usuario

Emerson

Emerson AS2-ACC Series Instrucciones de instalación

Emerson

Emerson GPC Series Instrucciones de instalación

Emerson

Emerson Bettis EHO Manual de usuario

Emerson

Emerson Net Safety ST3 Manual de usuario

Emerson

Emerson AS3-ACD Series Manual de usuario

Emerson

Emerson FISHER Yarway AT-13/23 Instrucciones de funcionamiento

Emerson

Emerson AVENTICS AR1 Manual de usuario

Emerson

Emerson Fisher 114PL Manual de usuario

Emerson

Emerson ACC/ARTM-7221/FC Manual de usuario

Emerson

Emerson PACSystems VersaSafe IC220SDL963 Manual de usuario

Emerson

Emerson TESCOM 44-1300 Series Manual de usuario

Emerson

Emerson FISHER T208 Series Manual de usuario

Emerson

Emerson Bettis RTS Manual de usuario

Emerson

Emerson Enardo EN Series Manual de usuario

Emerson

Emerson RIDGID MR-10 Manual de usuario

Emerson

Emerson Tartarini Dosaodor-D Manual de usuario

Emerson

Emerson ROSEMOUNT HMC-C01 Manual de usuario

Emerson

Emerson CAD 581 Series Instrucciones de instalación

Emerson

Emerson TESCOM 44-1100 Series Manual de usuario

Manuales populares de Equipos industriales de otras marcas

ABB

ABB Unifix AD Manual

Mark 7

Mark 7 Evolution Manual de usuario

Husky

Husky HyPET Manual de usuario

bora

bora PM-1800 Manual de usuario

Grizzly

Grizzly T32428 Manual de usuario

Siemens

Siemens 8MF1 Series Manual de usuario

ABB

ABB HT610965 Manual de usuario

ABB

ABB SafeLink Manual de usuario

Phoenix

Phoenix PHX-150 Manual de usuario

ABB

ABB A165-L32 Manual de usuario

ABB

ABB HT842936 Manual de usuario

Rioned

Rioned UrbanJet Manual de usuario

Hermetica

Hermetica 10 Series Manual de usuario

HORNER

HORNER OEE Solution Manual de usuario

Hammerhead

Hammerhead HG375 Manual de usuario

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instrucciones de uso

ABB

ABB HT566657 Manual de usuario

Webasto

Webasto GSE CAN Manual de usuario