Emerson PACSystems RX3i IC695CPE302 Manual de usuario

PACSystems™ RX3i Central Processing

Unit IC695CPE302

Quick Start Guide

GFK-3038C

 
i PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C 
Contents 
User Features.........................................................................................1 
Switches................................................................................................3 
Switch Operation ..................................................................................3 
Real-Time Clock Battery ........................................................................4 
Ethernet Port.........................................................................................4 
Serial Port..............................................................................................5 
Removable Data Storage Devices (RDSDs).............................................5 
Energy Pack...........................................................................................6 
Light-Emitting Diode Indicators (LEDs)..................................................6 
Hardware Installation............................................................................9 
Initial Checks ..............................................................................................................9 
Installation Location..................................................................................................10 
Installation in Hazardous Areas ...........................................................11 
Class 1 Division 2 Groups ABCD..............................................................................11 
ATEX Zone 2............................................................................................................12 
Module Installation .............................................................................12 
Module Initial Startup..........................................................................13 
Initial Configuration...................................................................................................14 
Additional Information...............................................................................................16 
General Contact Information.....................................................................................17 

1 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C

User Features

The PACSystems™RX3i CPE302 can be used to perform real time control of

machines, processes, and material handling systems. The CPU

communicates with the programmer via the internal Ethernet port or a

serial port. It communicates with I/O and Intelligent Option modules over a

dual PCI/Serial backplane.

▪Supports an updated OPC stack and encrypting connections

▪Supports PME’s new GUI management interface for OPC UA configuration

integration (start, stop, restart, clear, and provisioning mode)

▪Supports the new PAC Security tool available for certificate trust management

of clients and servers

▪Contains 5 Mbytes of user memory and 5 Mbytes of non-volatile flash user

memory

▪Supports Battery-less retention of user memory

▪Configured with an Energy Pack IC695ACC400 to power the CPU long enough

to write user memory to non-volatile storage (NVS) on system power loss

▪Equipped with configurable data and program memory

▪Supports programming in Ladder Diagram, Structured Text, Function Block

Diagram, and C

▪Supports auto-located Symbolic Variables that can use any amount of user

memory

▪Equipped with reference table sizes to include 32 Kbits for discrete %I and %Q

and up to 32Kwords each for analog %AI and %AQ

2 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C

▪Supports most Series 90-30 modules and expansion racks. For supported I/O,

Communications, Motion, and Intelligent modules, refer to the PACSystems

RX3i Hardware and Installation Manual, GFK-2314

▪Supports up to 512 program blocks (Maximum size for a block is 128KB)

▪Configured with an RS-232 serial port

▪Enabled with an embedded Ethernet interface to support up to 32

simultaneous SRTP Server connections, up to 16 simultaneous Modbus/TCP

Server connections, and up to 16 simultaneous communications channels of

either SRTP Channels or Modbus/TCP Client channels. For details, refer to the

PACSystems RX3i TCP/IP Ethernet Communications User Manual, GFK-2224

▪Supports OPC UA

▪Supports Ethernet Global Data, Class 1

▪Supports HART®Pass Through

▪Time synchronization to SNTP Time Server on Ethernet network when used

with a rack-based Ethernet module (IC695ETM001) version 5.0 or later

▪Enhanced ability to display serial number and date code in PME’s Device

Information Details.

▪Ability to transfer applications to and from USB 2.0 A type removable data

storage devices, or RDSDs.

▪Compliant with EU RoHS Directive 2002/95/EC using the following

exemptions identified in the Annex: 7(a), 7(c)-I and III, and 15.

HART® is a registered trademark of the HART Communication Foundation of Austin, Texas USA.

Any use of the term HART hereafter in this document, or any document referenced by this

document, implies the registered trademark.

3 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C

Switches

The RDSD and Run Mode switches are located behind the front protective

door. The Reset switch is not used. Switch operation is given in the

following table.

Switch Operation

RDSD Switches

Function

Start pushbutton

Pressing this switch initiates RDSD data transfer. (The

three-position switch must be set to Upload or

Download.)

Three-position switch

Enables/disables RDSD data transfer and selects the

direction of data transfer.

Upload

Loads application from CPU to RDSD.

Off

Disables RDSD data transfer.

Download

Stores application from RDSD to CPU.

Run Mode Switch

A three-position switch which operates as follows:

Switch Position

CPU and Sweep Mode

Memory Protection

Run I/O Enable

The CPU runs with I/O sweep

enabled.

User program memory is

read only.

Run Output Disable

The CPU runs with outputs

disabled.

User program memory is

read only.

Stop

The CPU is not allowed to go

into Run mode.

User program memory

can be written.

The Run Mode switch can be disabled in the programming software in Hardware

Configuration (HWC). The switch’s memory protection function can be disabled

separately in HWC. The Run Mode switch is enabled by default. The memory

protection functionality is disabled by default.

4 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C

Real-Time Clock Battery

The CPE302 is shipped with a real time

clock (RTC) battery (IC690ACC001)

installed, with a pull-tab on the battery.

The pull tab should be removed before

installing the CPE302.

There are no diagnostics or indicators to

monitor RTC battery status. The RTC

battery has an estimated life of 5 years

and must be replaced every 5 years on a

regular maintenance schedule. If the RTC

battery fails, the CPU date and time is

reset to 12:00 AM, 01-10-2000 at startup.

The CPU operates normally with a failed

or missing RTC battery; only the initial

CPU Time-of-day (TOD) clock information

will be incorrect.

Figure 1: Real-Time Clock

Battery

Ethernet Port

The embedded Ethernet interface supports communications with the

Machine Edition programming software using the proprietary SRTP

protocol. The CPE302 CPU provides two SRTP server connections.

The embedded Ethernet interface has one RJ-45 Ethernet port that

automatically senses the data rate (10 Mbps or 100 Mbps), duplex status

(half or full duplex), and cabling arrangement (straight through or

crossover) of the attached link.

5 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C

Serial Port

The CPE302 provides one RS-232 serial interface to external devices. This

port can be used for firmware upgrades. The port is electrically isolated. For

serial port pin assignments and details on serial communications, refer to

the PACSystems RX3i CPU Reference Manual, GFK-2222.

The RS-232 port does not supply the 5 VDC power offered by other RX3i

and Series 90-30 CPUs. Cable IC693CBL316 must be used for RS-232 serial

connections to the CPE302.

Removable Data Storage Devices

(RDSDs)

The CPE302 provides the ability to transfer applications to and from an

RDSD (USB compatible device, such as a memory stick, smart phone, digital

camera or MP3 device). Once the data is copied to the RDSD, it can be

written to other RX3i CPE302 CPUs with no programmer software needed.

The RDSD interface requires a user-supplied flash memory device that

complies with the USB 2.0 Specification.

The USB port must be enabled in the RX3i configuration in order to transfer

data between the CPU and the RDSD. The CPE302 is shipped with the RDSD

(USB) port enabled. Complete details of the use of RDSDs are found in the

PACSystems RX3i CPU Reference Manual, GFK-2222.

6 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C

Energy Pack

The CPE302 preserves user memory using an Energy Pack without the need

to periodically replace batteries. The IC695ACC400 Energy Pack powers the

CPU long enough for the CPU to write its user memory contents to the

CPU’s non-volatile storage during a system power loss. Installation of the

Energy Pack is found below.

Light-Emitting Diode Indicators (LEDs)

OK —indicates module readiness to perform normal operations.

Green, ON

steady

CPU passed power-up diagnostics, functioning

properly

OFF

Power is not applied, or CPU has a problem,

which may be indicated by RN and EN blink

pattern

Green, blinking

CPU in Stop-Halt state; possible watchdog

timer fault. Refer to the fault tables. If the

programmer cannot connect, cycle power

with a charged Energy Pack attached and refer

to fault tables

RN —indicates the run state of the CPU.

Green, ON

steady

CPU is in Run mode.

OFF

CPU is in Stop mode.

7 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C

Green,

blinking in

unison with

CPU is in boot mode and is waiting

for a firmware update through a

serial port.

EN —indicates outputs enabled.

Green, ON

steady

Output scan is enabled.

OFF

Output scan is disabled.

CM —indicates activity on the serial communications port.

Green, blinking

Signal activity on the COM1 port.

OFF

No activity on COM1 port.

IO FORCE —indicates override on a bit reference.

Amber, ON

steady

Override active on at least one-bit reference.

OFF

No overrides applied.

STATUS —indicates Energy Pack status.

OFF

Energy Pack not connected.

Green, blinking

Energy Pack charging; not yet charged

above the

minimum operating voltage.

Red, ON

Energy Pack circuit fault.

8 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C

Red, blinking

Energy Pack near its end of life and should

replaced soon.

Green, ON

steady

Energy Pack is charabove its minimum

operating voltage.

SYS FLT —indicates presence of a fatal fault.

OFF

No fatal faults.

Red, ON

CPU is in Stop/Faulted mode because a

fatal fault

has occurred.

RDSD —indicates signal activity on the RDSD/COM2/USB port.

Green, blinking

COM2 port activity

OFF

No COM2 port activity

Este manual sirve para los siguientes modelos

Otros manuales de Controladores de Emerson

Emerson

Emerson Dixell XR06CH BMB Diagrama de cableado

Emerson

Emerson Fisher S200 Series Manual de usuario

Emerson

Emerson Tartarini M Series Manual de usuario

Emerson

Emerson Fisher 64 Series Manual de usuario

Emerson

Emerson Baumann 24000CVF Manual de usuario

Emerson

Emerson Bettis XTE3000 Manual de usuario

Emerson

Emerson Site Supervisor Manual de usuario

Emerson

Emerson Fisher M Series Manual de usuario

Emerson

Emerson Bettis Q series Manual de instrucciones

Emerson

Emerson Fisher 67D Series Manual de usuario

Emerson

Emerson Dixell XR40D Diagrama de cableado

Emerson

Emerson Fisher 61 Series Manual de usuario

Emerson

Emerson Dixell XR44CX Diagrama de cableado

Emerson

Emerson Bettis RTS FL Series Manual de usuario

Emerson

Emerson Fisher 92C Manual de usuario

Emerson

Emerson Branson 2000X Manual de usuario

Emerson

Emerson COPELAND XC PRO Manual del propietario

Emerson

Emerson REGAL 3F Manual de usuario

Emerson

Emerson AW Series Manual de usuario

Emerson

Emerson Fisher 627B Series Manual de usuario

Emerson

Emerson Bettis 2000 Series Manual

Emerson

Emerson Fisher 299HR Manual de usuario

Emerson

Emerson Fisher S202 Manual de usuario

Emerson

Emerson FB3000 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

3M MicroTouch EX113 Manual de usuario