Emerson SM-I/O 24V Protected Manual de usuario

User Guide

Solutions Module for:

• Unidrive SP

•Commander SK

•Commander GP20

Part Number: 0471-0072-02

Issue: 2

www.controltechniques.com

SM-I/O 24V

Protected

General Information

The manufacturer accepts no liability for any consequences resulting from inappropriate, negligent

or incorrect installation or adjustment of the optional operating parameters of the equipment or from

mismatching the variable speed drive with the motor.

The contents of this guide are believed to be correct at the time of printing. In the interests of a

commitment to a policy of continuous development and improvement, the manufacturer reserves the

right to change the specification of the product or its performance, or the contents of this guide,

without notice.

means, electrical or mechanical including photocopying, recording or by an information storage or

retrieval system, without permission in writing from the publisher.

Drive software version

The SM-I/O 24V Protected can only be used with the following drive software version:

Unidrive SP: ≥V01.07.00

Commander SK: ≥V01.06.00

Commander GP20: ≥V01.07.00

Issue: 2

SM-I/O 24V Protected User Guide 3

Issue Number: 2 www.controltechniques.com

Contents

1 How to use this guide ....................................................4

1.1 Intended personnel ..................................................................................4

1.2 Information ..............................................................................................4

2 Introduction ....................................................................5

2.1 Features ..................................................................................................5

2.2 Solutions Module identification ................................................................5

2.3 Conventions used in this guide ...............................................................6

2.4 Solutions Module I/O ...............................................................................7

2.5 Digital I/O .................................................................................................7

2.6 Analogue output ......................................................................................8

2.7 Relays .....................................................................................................8

3 Safety Information ..........................................................9

3.1 Warnings, Cautions and Notes ................................................................9

3.2 Electrical safety - general warning ..........................................................9

3.3 System design and safety of personnel ..................................................9

3.4 Environmental limits ..............................................................................10

3.5 Compliance with regulations .................................................................10

3.6 Motor .....................................................................................................10

3.7 Adjusting parameters ............................................................................10

4 Installing the Solutions Module ..................................11

4.1 Installation .............................................................................................11

4.2 Terminal descriptions ............................................................................14

4.3 Wiring, shield connections .....................................................................15

5 Parameters ....................................................................16

5.1 Introduction ............................................................................................16

5.2 Single line descriptions ..........................................................................18

5.3 Logic diagrams ......................................................................................19

5.4 Parameter descriptions .........................................................................25

6 Diagnostics ...................................................................32

6.1 Displaying the trip history ......................................................................32

6.2 Unidrive SP / Commander GP20 trip descriptions ................................34

6.3 Commander SK trip descriptions ...........................................................35

7 Terminal specification .................................................36

8 Protection .....................................................................38

8.1 E.M.C immunity .....................................................................................38

8.2 Incorrect wiring ......................................................................................38

Index ..............................................................................39

4SM-I/O 24V Protected User Guide

www.controltechniques.com Issue Number: 2

1 How to use this guide

1.1 Intended personnel

This guide is intended for personnel who have the necessary training and experience in

system design, installation, commissioning and maintenance.

1.2 Information

This guide contains information covering the identification of the Solutions Module,

terminal layout for installation, fitting of the Solutions Module to the drive, parameter

details and diagnosis information. Additional to the aforementioned are the

specifications of the Solutions Module.

SM-I/O 24V Protected User Guide 5

Issue Number: 2 www.controltechniques.com

How to use this guide Safety Information

Introduction

Installing the

Solutions Module Parameters Diagnostics Terminal specification Protection Index

2 Introduction

2.1 Features

The SM-I/O 24V Protected is designed as an over voltage protected I/O Solution

Module.

The Solutions Module is able to withstand a +48V input voltage being applied to the

+24V Digital I/O terminals.

The SM-I/O 24V Protected can be used on the following products:

• Unidrive SP

• Commander SK

• Commander GP20

The SM-I/O 24V Protected increases the I/O capability of the drive by adding the

following to the existing I/O:

• 2 x Analogue current outputs

• 4 x Digital inputs/outputs*

• 3 x Digital inputs

• 2 x Relay (30Vdc contact rating)**

All connections from the Solutions Module to the drive are made via the drive connector.

Connections from external equipment to the relay, digital I/O and analogue outputs are

made via a 17-way pluggable screw connector.

On the Unidrive SP a total of three SM-I/O 24V Protected modules can be fitted at any

one time. On the Commander SK only one can be fitted, on the Commander GP20 two

can be fitted.

*Only three digital outputs are available with Commander SK.

**1 relay on Commander SK

2.2 Solutions Module identification

Figure 2-1 SM-I/O 24V Protected

The SM-I/O 24V Protected can be identified by:

1. The label located on the underside of the Solutions Module.

2. The colour coding across the front of the Solutions Module, with the SM-I/O 24V

Protected being cobalt blue.

6SM-I/O 24V Protected User Guide

www.controltechniques.com Issue Number: 2

Figure 2-2 SM-I/O 24V Protected label

2.2.1 Date code format

The date code is split into two sections: a letter followed by a number.

The letter indicates the year, and the number indicates the week number (within the

year) in which the Solutions Module was built.

The letters go in alphabetical order, starting with A in 1990 (B in 1991, C in 1992 etc.).

Example:

A date code of L35 would correspond to week 35 of year 2002.

2.3 Conventions used in this guide

The configuration of the host drive and Solutions Module is done using menus and

parameters. A menu is a logical collection of parameters that have similar functionality.

In the case of a Solutions Module, the parameters will appear in menu 15 for the

Commander SK, and in menu 15, 16 or 17 for the Unidrive SP and 15, 16 on the

Commander GP20 depending on the slot the module is fitted into. The menu is

determined by the number before the decimal point.

The method used to determine the menu or parameter is as follows:

•Prxx.00 - signifies any menu and parameter number 00.

•Prx.XX - where xsignifies the menu allocated to the Solutions Module (this could

be 15, 16 or 17 on the Unidrive SP, 15 or 16 on Commander GP20 but will always

be 15 on the Commander SK) and XX signifies the parameter number.

SM-I/O 24V Protected

Issue: 2.00 STDJ41

Ser No : 3000005001

olutions Module

name

Hardware

issue

number

Customer

and date code

Serial number

SM-I/O 24V Protected User Guide 7

Issue Number: 2 www.controltechniques.com

How to use this guide Safety Information

Introduction

Installing the

Solutions Module Parameters Diagnostics Terminal specification Protection Index

2.4 Solutions Module I/O

2.5 Digital I/O

All digital I/O complies with IEC 61131-2, clause 3.3.1 type 1, (i.e. >2mA @ +15Vdc).

For type 2 input, the user will need to add extra load externally.

Three terminals are dedicated digital inputs (4 with Commander SK); the functionality of

these inputs is as follows:

• The logic state of the input is monitored by a RO parameter

• The logic state can be inverted

• The digital input can be programmed to any unprotected parameter. The destination

parameter value will always be either 0 or 1 depending on the state of the input.

Four terminals are programmable as either digital inputs or output terminals (3 with

Commander SK), the functionality of these terminals is as follows:

Input

• The logic state of each input is monitored by a RO parameter

• The logic state can be inverted

• The digital input can be programmed to any unprotected parameter. The destination

parameter value will always be either 0 or 1 depending on the state of the input

Output

• The logic state of each output is monitored by a RO parameter

• The logic state can be inverted

• The digital outputs can be sourced from any parameter.

In the case where an integer parameter is used as the source, the threshold of

the output switching between low and high states is 50% of the parameter’s

maximum.

E.g. Source parameter = Pr 18.11 (maximum = 32767)

50% of 32767 = 16383 (due to integer truncation)

Therefore, if Pr 18.11 ≥16383 the output will be high

if Pr 18.11 < 16383 the output will be low

• The digital outputs can only source current

Solution Module I/O only operates in positive logic mode.

All I/O and relays are user programmable for function and signal processing.

All new source and destination routing only changes to new set up locations when the

drive is reset.

By default, the digital inputs/outputs on the Solutions Module are configured to operate

as inputs, except Digital I/O 4 which is configured as an output (input only for

Commander SK).

The logic state of a digital input will operate even without a destination parameter

programmed.

NOTE

Function Quantity

Digital inputs 3 (4 on Commander SK)

Function Quantity

Programmable digital inputs / outputs 4**

8SM-I/O 24V Protected User Guide

www.controltechniques.com Issue Number: 2

• The four digital outputs of the Solutions Module (three digital outputs with

Commander SK) are able to source 40 mA to the total combination of output

channels (e.g. 4 x 10mA or 1 x 40mA). When the current drawn exceeds safe limits,

all the outputs will be disabled through hardware and trip the drive to alert the user

to the fault condition.

**A maximum of three digital outputs are available with Commander SK.

2.6 Analogue output

Two terminals have a dedicated analogue output with the following functions:

• The output can be used to convey the value of any valid source parameter to

external equipment*.

• The output operates in one of the following modes as set in Pr

x.39

: 0-20, 20-0, 4-20

and 20-4.

• A scaling factor can be applied to the analogue output signal*

*Only available on analogue output 1 with Commander SK.

2.7 Relays

The relay can be used to convey the logic state of any parameter to external equipment.

The logic state is processed as follows:

• Any source parameter is assigned to relay.

• The logic state can be inverted.

• The software state of the coil is monitored by a parameter.

Function Quantity

Unipolar current output 2

Function Quantity

Number of relays 2 (1 on Commander SK)

SM-I/O 24V Protected User Guide 9

Issue Number: 2 www.controltechniques.com

How to use this guide

Safety Information

Introduction Installing the

Solutions Module Parameters Diagnostics Terminal specification Protection Index

3 Safety Information

3.1 Warnings, Cautions and Notes

3.2 Electrical safety - general warning

The voltages used in the drive can cause severe electrical shock and/or burns, and

could be lethal. Extreme care is necessary at all times when working with or adjacent to

the drive.

Specific warnings are given at the relevant places in this User Guide.

3.3 System design and safety of personnel

The drive is intended as a component for professional incorporation into complete

equipment or a system. If installed incorrectly, the drive may present a safety hazard.

The drive uses high voltages and currents, carries a high level of stored electrical

energy, and is used to control equipment which can cause injury.

Close attention is required to the electrical installation and the system design to avoid

hazards either in normal operation or in the event of equipment malfunction. System

design, installation, commissioning and maintenance must be carried out by personnel

who have the necessary training and experience. They must read this safety information

and this User Guide carefully.

The STOP and SECURE DISABLE functions of the drive do not isolate dangerous

voltages from the output of the drive or from any external option unit. The supply must

be disconnected by an approved electrical isolation device before gaining access to the

electrical connections.

With the sole exception of the SECURE DISABLE function, none of the drive

functions must be used to ensure safety of personnel, i.e. they must not be used

for safety-related functions.

Note that the SECURE DISABLE function is only available as standard on the Unidrive

SP and Commander GP20. The Commander SK does not have a SECURE DISABLE

input.

Careful consideration must be given to the functions of the drive which might result in a

hazard, either through their intended behaviour or through incorrect operation due to a

fault. In any application where a malfunction of the drive or its control system could lead

to or allow damage, loss or injury, a risk analysis must be carried out, and where

necessary, further measures taken to reduce the risk - for example, an over-speed

protection device in case of failure of the speed control, or a fail-safe mechanical brake

A Warning contains information, which is essential for avoiding a safety hazard.

A Caution contains information, which is necessary for avoiding a risk of damage to the

product or other equipment.

A Note contains information, which helps to ensure correct operation of the product.

WARNING

CAUT IO N

NOTE

10 SM-I/O 24V Protected User Guide

www.controltechniques.com Issue Number: 2

in case of loss of motor braking.

The SECURE DISABLE function and secure input meet the requirements of EN954-1

category 3 for the prevention of unexpected starting of the drive. They may be used in a

safety-related application. The system designer is responsible for ensuring that the

complete system is safe and designed correctly according to the relevant safety

standards.

3.4 Environmental limits

Instructions in the Unidrive SP User Guide, Commander GP20 User Guide,

Commander SK Getting Started Guide, Commander SK Technical Data Guide

regarding transport, storage, installation and use of the drive must be complied with,

including the specified environmental limits. Drives must not be subjected to excessive

physical force.

3.5 Compliance with regulations

The installer is responsible for complying with all relevant regulations, such as national

wiring regulations, accident prevention regulations and electromagnetic compatibility

(EMC) regulations. Particular attention must be given to the cross-sectional areas of

conductors, the selection of fuses or other protection, and protective earth (ground)

connections.

The Unidrive SP User Guide, Commander GP20 User Guide and Commander SK

Technical Data Guide contain instructions for achieving compliance with specific EMC

standards.

Within the European Union, all machinery in which this product is used must comply

with the following directives:

98/37/EC: Safety of machinery.

89/336/EEC: Electromagnetic Compatibility.

3.6 Motor

Ensure the motor is installed in accordance with the manufacturer’s recommendations.

Ensure the motor shaft is not exposed.

Standard squirrel cage induction motors are designed for single speed operation. If it is

intended to use the capability of the drive to run a motor at speeds above its designed

maximum, it is strongly recommended that the manufacturer is consulted first.

Low speeds may cause the motor to overheat because the cooling fan becomes less

effective. The motor should be fitted with a protection thermistor. If necessary, an

electric forced vent fan should be used.

The values of the motor parameters set in the drive affect the protection of the motor.

The default values in the drive should not be relied upon.

It is essential that the correct value is entered in the motor rated current parameter:

Pr 0.46 for Unidrive SP / Commander GP20 and Pr 06 in Commander SK. This affects

the thermal protection of the motor.

3.7 Adjusting parameters

Some parameters have a profound effect on the operation of the drive. They must not

be altered without careful consideration of the impact on the controlled system.

Measures must be taken to prevent unwanted changes due to error or tampering.

Tabla de contenidos

Otros manuales de Unidad de control de Emerson

Emerson

Emerson Fisher Baumann 24003 Manual de usuario

Emerson

Emerson Dixell XEC Supercap Diagrama de cableado

Emerson

Emerson Bettis XTE3000 Manual de usuario

Emerson

Emerson Bettis Q series Manual de usuario

Emerson

Emerson Anderson Greenwood 9300 Series Manual de usuario

Emerson

Emerson KEYSTONE F635 Instrucciones de instalación

Emerson

Emerson 289 Series Manual de usuario

Emerson

Emerson Fisher EWD Manual de usuario

Emerson

Emerson FRM-2 Manual

Emerson

Emerson FISHER NotchFlo DST Manual de usuario

Emerson

Emerson Fisher Snappy Joe N550 Manual de usuario

Emerson

Emerson Fisher 167DA Manual de usuario

Emerson

Emerson Baumann 83000 Manual de usuario

Emerson

Emerson PENBERTHY N7 Series Manual

Emerson

Emerson Fisher TBX Manual de usuario

Emerson

Emerson TARTARINI BM9 Manual de usuario

Emerson

Emerson Keystone Manual de usuario

Emerson

Emerson Keystone Manual de usuario

Emerson

Emerson Fisher MR98LD Manual de usuario

Emerson

Emerson Liebert Challenger 3000 Manual de usuario

Emerson

Emerson YARWAY GS-1 Manual de usuario

Emerson

Emerson YARWAY 60Y Series Manual de usuario

Emerson

Emerson Fisher C407-10 Manual de usuario

Emerson

Emerson ASCO 353 Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario