Emerson Bettis OM13-SCE300 Manual de usuario

Installation, Operation and Maintenance Manual

VCIOM-17114-EN Rev. 1

August 2022

Bettis OM13 - SCE300

3-Wires Module

Notes

August 2022

Installation, Operation and Maintenance Manual

VCIOM-17114-EN Rev. 1

This page intentionally left blank

Installation, Operation and Maintenance Manual

VCIOM-17114-EN Rev. 1

Table of Contents

August 2022

Table of Contents

Section 1: Optional Module 13: 3-Wires Module

1.1 OM13 Module Functionality ....................................................................... 1

1.2 Manufacturer ............................................................................................. 2

Section 2: Installation

2.1 Assembling Procedure for Models 63-125 Nm

Old Version (US or Non-US Market) ............................................................. 4

2.2 Assembling Procedure for Models 250-500-1000-2000 Nm

Old Version (US or Non-US Market) ............................................................. 9

2.3 Assembling Procedure for Models 63-125 Nm

New Version (US or Non-US Market) ........................................................... 14

2.4 Assembling Procedure for Models 250-500-1000-2000 Nm

New Version (US or Non-US Market) ........................................................... 20

Section 3: OM13 Module Setting and Conguration

OM13 Module Setting and Conguraton .............................................................. 25

Section 4: OM13 Kit

OM13 Kit .............................................................................................................. 26

Section 5: OM13 Wiring Diagram

OM13 Wiring Diagram ......................................................................................... 30

Notes

August 2022

Installation, Operation and Maintenance Manual

VCIOM-17114-EN Rev. 1

This page intentionally left blank

Installation, Operation and Maintenance Manual

VCIOM-17114-EN Rev. 1 August 2022

Optional Module 13: 3-Wires Module

Section 1: Optional Module 13: 3-Wires Module

NOTE:

Before installation, these instructions must be fully read and understood.

Section 1: Optional Module 13:

3-Wires Module

1.1 OM13 Module Functionality

The OM13 3-wires module is supplied as an option to the Bettis SCE300 actuators. It is

possible to receive the actuator already equipped with the OM13, ordering it with the

basic feature. Alternatively, it is possible to order the OM13 as a separate kit and install

it in the basic actuator in the factory or in the field. The OM13 is an optional module

suitable to accomplish the following SCE300 actuator additional functionality:

• 120/240 V AC 1-phase, 50/60 Hz, 3-wire control for open/close operations,

without additional power supply.

NOTE:

For decommissioning instructions, please refer to the relevant section in the SCE300

VCIOM-15516-EN.

NOTE:

The OM13 command has to be provided by two separate switches for open and for close

with a delay of at least one second between the two commands, when reversing the

operation from open to close or vice versa.

!WARNING

SCE300 actuator must be electrically isolated before any disassembling or

reassembling operations. Before any disassembling or reassembling operations,

please follow in detail the relevant section of the Installation, Operation and

Maintenance Manual (latest revision available).

!WARNING

The electronic parts of the SCE300 actuators and all option modules can be damaged

by a discharge of static electricity. Before you start, touch a grounded metal surface to

discharge any static electricity.

August 2022

Installation, Operation and Maintenance Manual

VCIOM-17114-EN Rev. 1

2Optional Module 13: 3-Wires Module

Section 1: Optional Module 13: 3-Wires Module

! WARNING

It is assumed that the installation, conguration, commissioning, maintenance, and repair

works are carried out by qualied personnel and checked by responsible specialists.

! WARNING

Repair work, other than operations outlined in this manual, is strictly reserved to qualied

Emerson personnel or to personnel authorized by the company itself.

1.2 Manufacturer

Manufacturer with respect to Machinery Directive 98/37: as specied on the SCE300 label.

Installation, Operation and Maintenance Manual

VCIOM-17114-EN Rev. 1 August 2022

Installation

Section 2: Installation

To assemble the OM13 into the SCE300 actuator, proceed as follows:

• Ensure that all the parts received with the OM13 are available as described in

Section 4.

• Using Section 4, select only mechanical parts (screws and spacers) depending on

actuator models.

• Gather the right tools for the assembly and for setting the actuator controls.

• With an Allen wrench of 5 mm, unscrew the cover screws as shown in Figure 1.

• Remove the actuator cover as shown in Figure 2.

Figure 2

Figure 1

Follow one of the following assembling procedures depending on actuator model.

August 2022

Installation, Operation and Maintenance Manual

VCIOM-17114-EN Rev. 1

4Installation

Section 2: Installation

2.1 Assembling Procedure for Models 63-125 Nm

Old Version (US or Non-US Market)

• Verify that you received the correct OM13 3-wire module as shown in Figure 3.

• Remove the following as indicated in Figure 4:

— 3-pins connector cable

— 4-pins connector cable

— 8-pins connector cable

Figure 3

Figure 4

• Remove the 3-wire power connector cable from the power card as indicated in

Figure 5.

• Remove the 3 screws (3 pcs M3x10) from the logic board and screw the 3 metal

spacers as shown in Figure 6.

Installation, Operation and Maintenance Manual

VCIOM-17114-EN Rev. 1 August 2022

Installation

Section 2: Installation

Figure 5

Figure 6

• Place the OM13 card onto the spacers and tighten the 4 screws as shown in Figure 7.

• Remove the 2-pins connector cable from J1 on the power card as shown in Figure 8.

Figure 7

screws

metal spacers

August 2022

Installation, Operation and Maintenance Manual

VCIOM-17114-EN Rev. 1

6Installation

Section 2: Installation

Figure 8

• Connect the 2-wire power connector cable of the OM13 card to the power card as

shown in Figure 9.

• Connect the 3-wire power connector cable of the terminal board to the OM13

card as shown in Figure 10.

Figure 9

Figure 10

Tabla de contenidos

Otros manuales de Unidad de control de Emerson

Emerson

Emerson Keystone 990 Documento técnico

Emerson

Emerson Rosemount Analytical NGA2000 CLD Manual de usuario

Emerson

Emerson Keystone Figure 320 Manual de usuario

Emerson

Emerson Fisher 8532 Manual de usuario

Emerson

Emerson ALCO CONTROLS FSE-0 Manual de usuario

Emerson

Emerson Fisher Baumann 24003 Manual de usuario

Emerson

Emerson Fisher NPS 8 CHP Manual de usuario

Emerson

Emerson KTM Series Manual de usuario

Emerson

Emerson EXM Manual de usuario

Emerson

Emerson Fisher N551 Manual de usuario

Emerson

Emerson Kunkle Valve Series Manual de usuario

Emerson

Emerson Keystone Figure 952 Manual de usuario

Emerson

Emerson Keystone PED Guía rápida

Emerson

Emerson 581 Series Instrucciones de instalación

Emerson

Emerson Rosemount 68 Series Manual de usuario

Emerson

Emerson CROSBY BP SERIES Guía

Emerson

Emerson FASANI Manual de usuario

Emerson

Emerson Fisher OSE Manual de usuario

Emerson

Emerson COMX-430 Manual de usuario

Emerson

Emerson Liebert Challenger 3000 Manual de usuario

Emerson

Emerson Dixell XEV20D Manual de usuario

Emerson

Emerson E5 Manual de usuario

Emerson

Emerson Bettis XTE3000 Manual de usuario

Emerson

Emerson ES-805 Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario