Emerson Anderson Greenwood 81P Especificaciones técnicas

ANDERSON GREENWOOD TYPE 81P DSO PRESSURE RELIEF VALVES

MAINTENANCE INSTRUCTIONS

1 GENERAL

The Anderson Greenwood Type 81P Direct

Spring Operated (DSO) Relief Valve is a direct

acting spring loaded valve for liquid service and

uses a plastic seat and O-ring seals.

The intent of these instructions is to acquaint

the user with the maintenance of this product.

Please read these instructions carefully. This

product should only be used in accordance

with the applicable operating instructions and

within the application specifications of the

original purchase order. The installation and

Operational Safety Instructions (available at

www.valves.emerson.com) should be fully read

and understood before returning this product to

service after maintenance.

2 VALVE REPAIR (-4, -8 ORIFICE)

Refer to Figure 1

2.1 Disassembly

2.1.1 Relieve spring tension by turning the

pressure adjusting screw counter-

clockwise.

2.1.2 Remove inlet bushing, bushing seal and

valve internals.

2.1.3 Separate nozzle from guide by hitting

top of spindle on soft surface. Remove

spindle seals.

2.2 Repair

2.2.1 Hold spindle by skirt O.D. in soft jaw vise

and replace seat.

2.2.2 Examine nozzle and polish out any

scratches or nicks. Replace if necessary.

2.2.3 To obtain better seat seal with PTFE at

low set pressures, burnish seat against

nozzle by chucking spindle in lathe and

holding nozzle against spindle. Burnish

with small force and for short time as

PTFE deforms easily.

LUBRICANTS

Part Set pressure Lubricant

Spindle seals 50-1000psig (3.4 - 69.0barg) Dow Corning FS3451

Above 1000psig (69.0barg) Desco 600

Thread and adjusting bolt tip All Dow Corning 33

Engineering Doc. #05.9040.072 Rev. K

Before installation these instructions must be fully read and understood

WARNING

An attempt to repair this product by unauthorized

or unqualified persons voids the product warranty

and may cause damage to equipment and serious

injury or death to persons.

The product is a safety related component

intended for use in critical applications.

Theimproper application, installation or

maintenance of the product or the use of parts

or components not manufactured by Anderson

Greenwood may result in a failure of the product.

Any installation, maintenance, adjustment, test,

etc. performed on the product must be done

in accordance with the requirements of all

applicable Anderson Greenwood procedures and

instructions as well as applicable National and

International codes and standards.

VCIOM-01056-EN 16/12

TABLE OF CONTENTS

1. General........................................................... 1

2. Valve repair (-4, -8 orifice) ............................ 1

3. Valve repair (G, J orifice)............................... 3

4. Valve adjustment........................................... 4

5. Seat leakage .................................................. 5

2.3 Assembly

Assemble in reverse order of

disassembly. Lubricate the parts listed

below with the specified lubricant. Make

sure the nozzle is fully and squarely

seated in guide.

ANDERSON GREENWOOD TYPE 81P DSO PRESSURE RELIEF VALVES

MAINTENANCE INSTRUCTIONS

Seat detail

(-4 illustrated)

FIGURE 1

-4, -8 ORIFICE

Cap Pressure adjustment screw

Outlet

Nozzle

Spindle

Guide

Drag seal

Seat retainer screw

Bushing

Spindle seal

Spindle skirt

Seat

Spring washer

Spring

Body

Guide seal

Vent

Plug

Seal

Bushing seal

2.4 Soft goods repair kit

The part numbers for soft goods repair kits are listed below. Each kit contains the seat and

seals for all pressure ranges and the lubricant specified in paragraph 2.3.

MATERIAL

Orifice NBR FKM EPR

-4 04.4805.029 04.4805.032 04.4805.071

-8 04.4805.029 04.4805.032 04.4805.071

ANDERSON GREENWOOD TYPE 81P DSO PRESSURE RELIEF VALVES

MAINTENANCE INSTRUCTIONS

3 VALVE REPAIR (G, J ORIFICE)

Refer to Figure 2

3.1 Disassembly

3.1.1 Relieve spring tension.

3.1.2 Remove spring bonnet and valve internals.

3.1.3 Separate nozzle from guide by hitting top of spindle on soft surface.

3.2 Repair

3.2.1 Hold spindle by skirt O.D. in soft jaw vise and replace seat.

3.2.2 Examine nozzle and polish seating surface as required. Replace if necessary.

3.3 Assembly

Assemble in reverse order of disassembly. Lubricate the parts listed below with the

lubricant specified. Make sure the nozzle is fully and squarely seated in guide.

Seat detail

FIGURE 2

G, J ORIFICE

Cap

Pressure adjustment screw

Outlet

Nozzle

Spindle

Guide

Drag seal

Seat retainer screw

Bonnet

flange

Spindle seal

Bonnet

Seal

Seat

Seal

Spring washer

Spring

Body

Bonnet retainer ring

Vent

Plug

Seal

Flange bolt

4 VALVE ADJUSTMENT

4.1 General

The only adjustment required for the Type 81P valve is the set pressure. The reseat pressure

is not adjustable. Reseat will occur at approximately 75% to 80% of set pressure.

4.2 Proof test

The spindle seals and bonnet seal of the Type 81P valve shall be checked for integrity by

pressurizing the outlet with 30psig (207 kpag) of air. A soap solution shall be applied to the

exterior joints of the bonnet, including across the vent hole. There shall be no evidence of

leakage.

4.3 Set pressure

Type 81P liquid valves marked with the UV code stamp (relief capacity in volume of liquid per

time, GPM) shall be set using water and a 50 gallon pressure vessel.

When setting the valve using water, turn the spring adjustment screw on the bonnet in most

of the way. Increase the pressure to 107% ± 2% of nameplate set and back out screw until

the valve 'pops' or 'gushes' liquid. Set pressure is defined as 93% of that pressure where the

valve 'pops'.

Example liquid English liquid International liquid

Nameplate set = 75psig 5.2barg

'POP' or 'GUSH' = (107% ± 2%) 75 = 78.75 to 81.75psig (107% ± 2%) 5.2 = 5.4 to 5.6barg

Actual 'POP' = 80psig 5.5barg

Actual set = 80 (.93) = 74.4psig 5.5 (.93) = 5.1barg

ANDERSON GREENWOOD TYPE 81P DSO PRESSURE RELIEF VALVES

MAINTENANCE INSTRUCTIONS

3.4 Soft goods repair kit

The part numbers for soft goods repair kits are listed below. Each kit contains the seat and

seals for all pressure ranges and the lubricant specified in paragraph 3.3.

MATERIAL

Orifice NBR FKM EPR

G04.4805.030 04.4805.033 04.4805.072

J04.4805.031 04.4805.034 04.4805.073

LUBRICANTS

Part Set pressure Orifice Lubricant

Spindle seals 50-300psig (3.4 - 20.7barg) GDow Corning FS3451

50-100psig (3.4 - 6.9barg) JDow Corning FS3451

Spindle seals Above 300psig (20.7barg) GDesco 600

Above 100psig (6.9barg) JDesco 600

Thread and adjusting bolt tip All G and J Dow Corning 33

4.4 Adjustment tolerances

If the Type 81P liquid valve is not marked with the UV code stamp and if a water source is

not available valves with set pressures greater than 750psi (51.7barg) may be set on air

by adjusting the spring to obtain first crack at 95% of set pressure. The valve should not be

popped on air as this may damage the seat. For set pressures below 750psi (51.7barg), the

81P should only be set pressure adjusted using the water method above.

Note: valves with relief capacity in GPM must be set using water if the valve will bear the 'VR'

repair symbol stamp.

Type 81P air valves shall be set using an accumulator large enough to accurately measure

set pressure. Turn the spring adjustment screw on bonnet in most of the way. Increase

pressure to desired level and back out screw until valve pops. Lock screw with jam nut and

retest. Readjust as required.

Set pressure range Valve operating characteristics Tolerance or limit

Above 70psig (4.8barg) Set pressure ± 3% of nameplate set

70psig (4.8barg) and below Set pressure ± 2psig

100psig (6.9barg) and above Cracking pressure 92½% of nameplate set

50psig (3.4barg) to 99psig (6.8barg) Cracking pressure 80% of nameplate set

5 SEAT LEAKAGE

5.1 If the valve leaks after repair, check for the following:

5.1.1 Full and even seating of nozzle and guide.

5.1.2 Foreign particles trapped between the seat and nozzle. If any are found they may have

damaged the seat making it necessary to replace it.

5.1.3 Correct seat material for the valve set pressure. If item 1 and 2 reveal no evident seat

leakage source, the procedures described in section 5.2. may be used to eliminate seat

leakage. Section 5.2 applies only to PTFE seated -4 or -8 orifice type 81P with nameplate

set pressures that do not exceed 250 psig (1724 kPag).

5.2 Seat sealing procedures

Heat the valve for 15 to 30 minutes in an oven preheated to 250-265°F (121-129°C). A concentrated

heat source such as a heat gun or open flame must not be used. After the valve has air-cooled to

room temperature, retest per section 4 to ensure seat tightness. If results have not improved, the

valve should be disassembled and the seat replaced.

ANDERSON GREENWOOD TYPE 81P DSO PRESSURE RELIEF VALVES

MAINTENANCE INSTRUCTIONS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Emerson

Emerson

Emerson Keystone Figure 320 Manual de usuario

Emerson

Emerson Fisher ME00124272 Guía de configuración

Emerson

Emerson Keystone 952 Manual de usuario

Emerson

Emerson Micro Motion Manual de usuario

Emerson

Emerson FB1100 Manual de lista de piezas

Emerson

Emerson Numatics DeviceLogix G2-2 Series Manual de instrucciones

Emerson

Emerson SW95 Manual de usuario

Emerson

Emerson ANDERSON GREENWOOD MARVAC 121 Series Manual de usuario

Emerson

Emerson Fisher 122A Series Manual de usuario

Emerson

Emerson White-Rodgers 36C01 Manual de usuario

Emerson

Emerson Clarkson series Manual de usuario

Emerson

Emerson KEYSTONE F635 Instrucciones de instalación

Emerson

Emerson Anderson Greenwood M4TL Manual de usuario

Emerson

Emerson MVME7616E Guía de inicio rápido

Emerson

Emerson VersaMax CPU001 Manual de usuario

Emerson

Emerson VS-FL Series Manual de usuario

Emerson

Emerson Dixell XEV20D Manual de usuario

Emerson

Emerson EIM 2000 Series Manual de usuario

Emerson

Emerson Keystone K-Lok 360 Series Instrucciones de funcionamiento

Emerson

Emerson Yarway 9200 Series Manual de usuario

Emerson

Emerson Bettis XTE3000 Manual de usuario

Emerson

Emerson Anderson Greenwood Guía de inicio rápido

Emerson

Emerson Daniel 700 Series Manual de usuario

Emerson

Emerson Fisher EHD Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario