Elite Screens Spectrum Series Manual de usuario

Rev. V03022023DT (DS0241) www.elitescreens.com 1

Spectrum Series

Electric/Motorized Projection Screen

User Guide

Important Safety & Warning Precautions

Make sure to read this user’s guide and follow the procedure below.

Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO

extra Black Top Drop in the roller. Please be aware of this, as it will void your warranty with Elite

Screens. Unapproved changes or modifications (except for cutting the power cord for hardwire

installations) to this unit are prohibited and will void your warranty. For more information, please

contact our Technical Support Department.

Please retain this user’s guide for future reference.

To avoid damaging the unit, do not use with any unauthorized accessories not recommended by

the manufacturer.

Handle the unit carefully during transportation to avoid any damages.

To ensure safe and reliable operation, direct connection to a properly grounded power source is

advised.

The power outlet supplying power to the unit should be close to the unit and easily accessible.

Do not install the unit on uneven or inclined surfaces.

Do not put heavy objects on the power cord and position it properly to avoid creating a trip

obstacle.

Never overload the power cord to prevent an electric shock or fire due to a loose contact or a

short circuit.

There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by

yourself. No one except authorized technicians can open and make repairs to this unit.

Make sure the power source this unit is connected to has a continuous power flow.

If there is need to use an extension cord, make sure the cord has an equal rating as the appliance

to avoid overheat.

Do not handle the power plug when your hands are wet or your feet are in contact with water.

Do not use this unit under the following circumstances.

Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.

Avoid direct Sunshine, rain shower and moisture.

Keep away from fire sources and high temperature to prevent this device from overheating.

Cut off the power supply first before transportation or maintenance.

Fully disconnect from the power supply when the unit is not in use for a long period of time, as

should be done with any other electric household appliance.

To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is

obvious damage or if there are any evident broken parts.

Rev. V03022023DT (DS0241) www.elitescreens.com 2

Installation Warning

Individual modifications to this product are prohibited and will void the warranty with the manufacturer.

Please contact Elite Screens Customer Service for any questions.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur on a particular installation. If this

equipment causes harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures.

Reorient or relocate the receiving antenna of the device which may be casing the

interference.

Increase the separation between the screen and the device’s receiver.

Connect the equipment into a different power outlet other than the device

Pre-Installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign

particles such as dust, sawdust, and/or liquids.

Spectrum series | Controls and Accessories

A. IR Remote

ZRC1-IR

B. RF Remote

ZRC1-RF

C. Wall box

controller

ZRC1-WB

D. RJ50 Cable

ZZR1-RJ50

E. AAA batteries

F. Bubble Level

Screen operation

Electric Current: 100 ~ 110v voltage

1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.

2. Once the screen has power, you’ll be able to control it using any of the 5 methods described below.

Rev. V03022023DT (DS0241) www.elitescreens.com 3

5 Ways to control your Spectrum screen

1. IR Remote control (Item A, Fig 1): The Infrared functions by direct line of

sight contact using an effective beam range of 25 feet within a 30-degree angle.

Aim the IR remote directly at either the IR receiver on the Wall Box Controller or

on the screen to operate the screen.

Note: Assure there is no obstruction between the IR remote and IR receiver.

2. RF Remote Control (Item B): The radio waves eliminate the need for a direct line

of sight and has a longer distance control range.

The RF remote is already pre-synced/paired and ready to use. If synchronization/

pairing is needed, please follow the steps below.

How to synchronize/pair a new RF remote:

Press & hold the “Programming Key”, then press the “Up Key” on the Wall box controller (wall-box LED

flashes). Reference the wall box controller section for programming key location.

Then press the “Up Key” on the RF remote.

The Wall box LED will flash 5 times, to indicate the RF remote has been properly synchronized/paired.

LED

light

STOP

DOWN

Fig.1

IR/RF remote

IR Lens

(IR remote only)

How to change the RF code (For use when multiple screens/RF remotes are owned)

Changing the RF code avoids controlling multiple screens at the same time and prevents electrical interference leading to

accidental control of the screen.

1. Remove the batteries

2. Change the RF code switch

3. Insert the batteries

4. Synchronize it with the wall box controller

3. Wall box controller (Item C, Fig 3): The wall box controller switch is a wall mounted control box with an

up/stop/down button. It plugs directly into the screen’s RJ50 port.

Programming

Key

Wall box controller

Receiver

RJ50

cable

Wall box controller

SIDE VIEW

RJ50 PORT:

Connects to the

Screen RJ50

PORT (RJ50

CABLE ONLY)

3.5mm mono Projector

Trigger Port (if

Projector equipped)

Wall box

controller BACK

VIEW

Battery compartment

Default

“000”

RF Remote

BACK

VIEW

Slide Switches

for RF Code

change

Rev. V03022023DT (DS0241) www.elitescreens.com 4

4.Wired 5-12 volt trigger: Requires a 3.5mm to 3.5mm mono cable (not included)

Step 1: Connect one end the RJ50 cable to the screen and the other end to

the Wall box controller.

Step 2: Then connect one end the 3.5mm mono cable to the wall box

controller and the other to the projector.

Once the two cables have been connected, the wired trigger feature is

ready to synchronize the screen’s up/down operation with the projector’s

power cycle.

Projector on, screen drops

Projector off, screen raises

5. Wireless 5-12 volt trigger (Fig 5): Requires a 3.5mm to 3.5mm mono cable (not included).

The Radio Frequency (RF) remote control serves as a dual purpose, independently as a handheld remote control, or as a

Wireless 5-12 volt trigger. The radio frequency technology sends a wireless signal that synchronizes the screen’s drop &

rise with the projector’s power cycle.

Here’s how to set up your Wireless 5-12 volt trigger

The 5-12V wireless trigger should already be synced and ready to work.

Step1: Connect one end of the 3.5 mm mono trigger cable to the RF remote.

Step 2: Connect the other 3.5 mm mono end of the cable to your projector

Step 3: Turn on the projector and the screen should automatically deploy.

Step 4: Turn off your projector and the screen should automatically retract.

(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20- 30 seconds for

full off and on cycle each time)

Note: If the wireless trigger feature does not work, please resync the RF remote to the Wall box controller per the

instructions in the Radio Frequency remote section.

3.5 mm port

DC 5-12V

out

3.5mm to 3.5mm mono cable

Wall box controller

RJ50 cable

Fig. 4

ADVANCED Programming Key Instructions: (FOR ADVANCED USERS ONLY)

Wall box controller must be connected to the screen.

Mono 3.5mm

Projector Trigger

Port

Fig 5

3.5 mm port

DC 5-12V out

3.5mm to 3.5mm mono cable

STOP

DOWN

Projector

RF remote

control

SIDE VIEW

Projector

ATTENTION: Reducing the factory’s full screen drop may produce waves/wrinkles on the

projection surface on tab-tension screens. The full drop is recommended to allow the screen to rely

on the tab-tension system to maintain the projection surface flat and taut on all sides.

The same applies on non-tensioned screens, although some level of waves may be present due to the

nature of the screen not being tensioned. If wrinkles/waves develop after making the adjustment to

the desired drop position, reset it to the factory’s default position per the instructions below.

Rev. V03022023DT (DS0241) www.elitescreens.com 5

1. Preset the Screen’s Drop Position:

Use the RF/IR remote or Wall Box Controller to Drop the screen to the desired position you want to set it

at.

Press & hold the “Programming Key”, then press the “down key” on the Wall Box Controller. The LED

will flash 5 times to confirm new programmed drop position.

2. Clear/Reset the Screen’s Drop Position to factory default:

Press & Hold the “Programming Key + “Stop key” on the wall box controller.

Installation Instructions

Please consult a professional installer. Elite Screens is not liable for any faulty installations.

1. Select the installation location for your screen. Ensure that it is within reasonable proximity from your power source.

2. For best support of your screen, it is ideal to secure your screen into the studs of your house’s internal framework. If

studs are not available, use hollow anchors for mounting your wall screws into drywall. If you’re installing in a concrete

structure, use concrete bolts to secure your screen.

Always consult a professional installer or hardware professional to ensure that the proper screws and/or hardware are

being used.

3. Ensure that both brackets are in perfect level alignment with one another. Use wall/ceiling wood screws to secure to the

wood studs. Use hollow anchors if mounting in drywall.

4. The screen casing is designed to accept the wall screws directly. If not using the Optional L-Brackets

http://shop.elitescreens.com/accessories.aspx, be sure to position the washer between the head of the wall-screw and the

anchor slots on the screen’s casing.

5. Using a tape measure, mark the keyholes that are located at the back of the screen’s casing end cap.

6. After marking the area and predrilled hole, insert the screw and have at least 1/8” from the wall to mount the screen.

(See example in Figure 1.)

7. Figure 2 will show you an optional installation method using the drill holes located on top of the end caps for ceiling

installation.

PROGAMMING NOTE:

The programmed vertical drop position will have +/- 2" tolerance, which will depend on the temperature of the

installed screen environment.

Rev. V03022023DT (DS0241) www.elitescreens.com 6

For local Elite Screens contact or Technical Support, please visit

www.elitescreens.com

Optional installation method using the drill holes to hang the screen from the ceiling

Note:

Wall screws included with this product are

complementary and may not be adequate for all

mounting surfaces. Consult with a professional installer

or hardware store for proper mounting screws and

anchors.

Regardless of the mounting method, the screen should be

securely supported so that the vibration or pulling on the

viewing surface will not cause the screen case to become

loose or fall. The installer must ensure that proper

mounting hardware and the fasteners used are of

adequate strength and suitable for the mounting surface.

Screws

Otros manuales para Spectrum Series

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens DE103C82H Manual de usuario

Elite Screens

Elite Screens YardMaster Manual Series Manual de usuario

Elite Screens

Elite Screens VMAX113XWS Guía del usuario

Elite Screens

Elite Screens F60XWV1 Manual de usuario

Elite Screens

Elite Screens M85XWS1-SRM Manual de usuario

Elite Screens

Elite Screens Elite Home 2 Series Manual de usuario

Elite Screens

Elite Screens Elite CineTension Series Manual de usuario

Elite Screens

Elite Screens AR2 Series Manual de usuario

Elite Screens

Elite Screens CineTension B Series Manual de usuario

Elite Screens

Elite Screens Starling Tab-Tension 2 Series Guía

Elite Screens

Elite Screens Evanesce B Series Manual de usuario

Elite Screens

Elite Screens TE100HC2 Manual del propietario

Elite Screens

Elite Screens F100XWH1 Manual de usuario

Elite Screens

Elite Screens ezFrame Series Manual de usuario

Elite Screens

Elite Screens Electric100H Manual de usuario

Elite Screens

Elite Screens Starling Tension Series Manual de usuario

Elite Screens

Elite Screens Kestrel Stage Series Manual de usuario

Elite Screens

Elite Screens Starling Series Manual de usuario

Elite Screens

Elite Screens Saker Tension Series Manual de usuario

Elite Screens

Elite Screens VMAX Tab-Tension 3 Series Manual de usuario

Elite Screens

Elite Screens Ez-Frame Series Manual de usuario

Elite Screens

Elite Screens Evanesce B Series Guía

Elite Screens

Elite Screens Insta-RP Screen Series Manual de usuario

Elite Screens

Elite Screens Planate Tab-Tension Series Guía

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación