Elite Screens EzFrame Plus Series Manual de usuario

Large size Fixed Frame Projection Screen

ezFrame Plus Series

User’s Guide

PARTS LIST_

1. Frame Parts x’s 6 pcs (4 top/bottom frame pcs. + 2 side frame pcs)

2. Tension Rods x’s 6 pcs (4 top/bottomrods + 2 side rods)

3. Screen Materialx’s 1 pc

4. Center joints x’s 2 pcs

5. Elbow Jointsx’s4pcs

6. Wall bracketsx’s2-4pcs

7. Screws x’s 16 pcs

8. User Guide x’s pc

9. Center Support Bar x’s 1 – 2 pcs (depending on model/size)

10. Support joinerx’s 2 – 4 pcs (depending on model/size)

11. Fix Plates x’s 30 – 90 pcs (depending on model/size)

Note:&Please&make&sure&all&parts&are&included&in&your&package&before&proceeding&to&assemble&your&

Elite&Screens&fixed&frame&projection&screen.&

ASSEMBLING THE FRAME

1. Insert the center joint connector to the horizontal frame pieceand then fasten it with 2screws.

Rev.040114-JA 1 www.elitescreens.com

2. Insertthe other horizontal frame piece to thecenter joint connectorand then fasten it with 2 screws.

Make sure the frame piece lines up correctly beforeyou tighten the screws completely.

3. Insert both elbowjoint connectors into the long horizontal frame (fig.1).

Push

Short frame

Push Push

Joint

Long frame

( fig.1)

1/2Long frame

Push

Rev.040114-JA 2 www.elitescreens.com

Push

( fig.2)

Insert the exposed ends of the joint connectors

into the short (vertical) frame and align the four

corners so that they meet at perfect right angles

4. Join all four frame parts together following the steps showed below(fig.2).

5. After making sure that all four corners join at right angles to form a perfect rectangle,fasten the four

angles together by using the (x8) joint screws included(fig.3).

Screw

( fig.3)

Rev.040114-JA 3 www.elitescreens.com

Tension Rod (Horizontal) x 4

Tension Rod (Vertical) x 2

Tension Rod (horizontal)

Push

Tension Rod (Vertical)

ATTACHING THE SCREEN MATERIAL TO THE FRAME_

1. Lay out the screen and tension rods on a clean and dry surface. Insert the tension rods through the

sleeves according to their corresponding lengths on each edge of the screen as seen below(fig.4).

2. Place the screen material on the back of the built frame and slip the tension rods into the grooves

running along each side on the back of the frame. Clip the fix plates to the back of the frame to secure

the rods into place creating tension for a tight and flat surface(fig. 5 & fig. 6).

Steel rod

Push

( fig.4)

Steel rod

Screen

Push

Rod

Push

( fig.5)

Viewing surface

(Front of screen)

Steel rod

fix plate

Tension Rod

(fig. 5)

(fig. 6)

Rev.040114-JA 4 www.elitescreens.com

ATTACHING THE FIX PLATES_

1. Make sure that the material and frame are both lying face down on a clean, dry and non-abrasive surface.

2. Center the material inside the frame.

Please note the material will be noticeably smaller than the frame. Stretching the material is required to create a

sufficient amount of tension for perfect material flatness.

3. Start attaching the fix platesin the center of the long horizontal edge and (1) then alternate with the center short

sides (2) as shown in diagram(fig.7).

Note: Follow these instructions to make sure the material is properly fixed in the center position of the

frame. After attachingthe fix plates in sequence #2 (the center of the short sides), please remove the fix plates in

sequence #1(the center of the long horizontal edge) and reattach them again, and also remove the fix plates on

sequence# (2) and reattach them again.

4. Then continue to follow our recommended order numbers3-8 to properly distribute tension to the screen

material.

CENTER SUPPORT BAR

1. Insert the support joiner into each side of the center support bar to complete assembly.

support joiner

Center support bar

2. Insert the Center Support Barinto the upper top groove on the back of the frame (not where the fix plate

inserts are) with the bottom end near the approximate center point of the frameand place it in at an angle so that

both ends of the bar are in alignment with the groove(Fig. 8).

3. Slide the top end of the bar into the top center point

location to complete center support bar installation.This will

provide added stability to your frame and added tension

to the material.

支

撑

Center Support Bar

(fig. 7)

(fig. 8)

Screen material edge

Center&Support&Bar&

Fixed plate groove

(do not insert here)

Rev.040114-JA 5 www.elitescreens.com

INSTALLATION INSTRUCTIONS

1. Locate your desired installation location with a stud finder (recommended) and mark the drill-hole area of

where the screen is to be installed.

2. Drill a hole with the proper bit size according to the wood screws included.

3. Line up the wall brackets with the drilled holes on the installation location and screw them in using a

Philips screwdriver.

4. Position the fixed frame screen onto the top wall brackets as shown below and push down at the center of

the bottom frame to secure the installation.

5. The wall brackets allow flexibility by allowing the fixed frame screen to slide to the sides. This is an

important feature as it allows your screen to be properly centered.

6. Using&both&hands&finish&the&installation& by& pushing&the& lower& portion&of&the&fixed&frame& screen& into&the&

lower&bracket.&

CAUTION_

Please follow these instructions carefully to ensure proper maintenance and safetywith your Peregrine

Screen

1. When hanging the screen, please make sure that no other objects such as power switches, outlets, furniture,

ladders, windows, etc. occupy the space designated for your Fixed-Frame screen.

2. Regardless if the screen is hung on or installed into the wall, make sure that the proper mounting anchors are

used and that the weight is supported appropriately by a strong and structurally sound surface just as any large

and heavy picture frame should.

3. Frame parts are made of high quality velour-surfaced aluminum and should be handled with care.

4. When not in use cover the screen with a furniture sheet to protect it from dirt, grime, paint or any other

impurities.

5. When cleaning, use a damp soft cloth with warm water to remove any marks on the frame or screen surface.

6. Never attempt to use any solutions, chemicals, or abrasive cleaners on the screen surface.

7. In order to avoid damaging the screen, do not touch it directly with your fingers, tools or any other sharp or

abrasive objects.

8. Spare parts should be placed out of reach of small children in accordance with household safety guidelines.

For a local Elite Screens contact or Technical Support, please visit

www.elitescreens.com

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens AEON series Manual de usuario

Elite Screens

Elite Screens ezFrame R180WH1 Manual de usuario

Elite Screens

Elite Screens YardMaster Manual Series Manual de usuario

Elite Screens

Elite Screens Sable Frame B2 Series Manual de usuario

Elite Screens

Elite Screens EVANESCE TAB-TENSION Series Guía de referencia rápida

Elite Screens

Elite Screens ezFrame CineGrey 5D Manual de usuario

Elite Screens

Elite Screens Kestrel Stage Series Manual de usuario

Elite Screens

Elite Screens ezCinema Series Manual de usuario

Elite Screens

Elite Screens Spectrum Series Manual de usuario

Elite Screens

Elite Screens CineTension 2 Series Manual de usuario

Elite Screens

Elite Screens Insta-DE Series Manual de usuario

Elite Screens

Elite Screens TE100HC2 Manual de usuario

Elite Screens

Elite Screens Starling Tab-Tension Series Manual de usuario

Elite Screens

Elite Screens Aeon CineGrey 4D AT Series Manual de usuario

Elite Screens

Elite Screens B SERIES Manual de instrucciones

Elite Screens

Elite Screens StarFrame Series Manual de usuario

Elite Screens

Elite Screens PicoScreen Series Manual de usuario

Elite Screens

Elite Screens Manual SRM Pro Series Manual de instrucciones

Elite Screens

Elite Screens Evanesce AcousticPro UHD Series Manual de usuario

Elite Screens

Elite Screens Starling Tension Series Manual de usuario

Elite Screens

Elite Screens Lunette Series Manual de usuario

Elite Screens

Elite Screens Pop-Up Cinema Series Manual de usuario

Elite Screens

Elite Screens TE100HC2 Manual de usuario

Elite Screens

Elite Screens MicroFlip Screen Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación

Elite Screens ezFrame Plus Series Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas