UP/DOWN Footswitches –If no preset is currently loaded, pressing either
footswitch will load the preset associated with the currently displayed number. For
example, if the 8-STEP FC is displaying 0 and the right decimal point is not lit,
pressing either footswitch will load Preset 0.
If a preset is loaded, press and release the UP Footswitch and the digits on the 8-
STEP FC will increment by one while simultaneously loading the preset indicated by
the new number. For example, if your 8-STEP FC is displaying (0.) and you press the
UP Footswitch, the display will load and show Preset 1 (1.). The DOWN footswitch
does the same but instead decrements by one.
Press and hold either footswitch for approximately 1 second to jump up or down by
10 presets at a time, instead of just one. Keep holding down the footswitch to
continue to jump by 10 presets.
SELECT Knob –The SELECT knob can be used to scroll through the presets without
loading a new preset. Turn the knob clockwise to scroll up through the presets, turn
the knob counter-clockwise to scroll down. Press and release the SELECT knob to
load the currently displayed preset. If a preset is loaded, and you turn the SELECT
knob, the numbers will blink indicating that a different preset is actually loaded.
Press and hold the SELECT knob for approximately 3 seconds to save the current 8-
STEP setting to the preset number currently displayed. After holding the SELECT
knob for 3 seconds, the LED display blinks for 2 seconds, indicating that the preset
has been saved. The MODE LEDs on the 8-STEP main unit will also blink when saving
a preset.
- SAVING AND LOADING -
SAVING A PRESET
To save your current 8-STEP setting, turn the SELECT knob until the 8-STEP FC
displays the preset number you would like to save to. If a preset is empty, the middle
decimal LED will light. Now press and hold the SELECT knob for 3 seconds. After 3
seconds the digit display blinks for 2 seconds, indicating that the preset is saved. You
can now release the SELECT knob.
LOADING A PRESET
There are two ways to load a preset: the UP/DOWN footswitches or the SELECT
knob. Use the UP/DOWN footswitches to load the selected number, if the preset is
not already activated. Once a preset is loaded, use the UP/DOWN footswitches to
increment/decrement through the presets. The footswitches will both load and
change the preset number simultaneously.
Use the SELECT knob to scroll through the presets. Press and release SELECT to load
the currently displayed preset number.
PRESET CUE –If a sequence is running at the time you load a preset, the preset
does not load immediately. Instead the new preset is cued up and waits until the
current sequence ends and then loads; during this waiting period the digit display
blinks rapidly. The sequencer loads the new preset without missing a beat.
EDITING A PRESET
If you load a preset and then move a slider or change a mode setting on the 8-STEP
main unit, you will see both the decimal LED on the 8-STEP and the right decimal
point on the 8-STEP FC blink. The blinking LED indicates that the currently loaded
preset has been changed or edited in some way. If you would like to save this edit
and overwrite the original preset, hold down SELECT. If you would like to save the
edit to a different preset, turn the SELECT knob to a new number, then press and
hold the SELECT knob. While you are turning the SELECT knob to a different preset
number, the digits will blink, indicating that the currently displayed number is not the
preset that is loaded. If you want to save your preset to an empty preset, look for a
preset number where the middle decimal LED is lit.
UNLOADING A PRESET
Unloading a preset forces the 8-STEP main unit to go back to its What You See Is
What You Get mode, where all the current slider positions indicate the 8-STEP’s
actual setting. To unload the current preset, make sure the current preset number is
displayed then press and release the SELECT knob. Upon unloading, both the decimal
LED on the 8-STEP main unit and the right decimal point on the 8-STEP FC will turn
off.
- POWER -
Power for the 8-STEP Foot Controller comes from the 8-STEP main unit, through a
standard mono/TS 1/4” instrument cable. The Foot Controller does not require
batteries or a separate AC Adapter. Its only source of power is the 8-STEP.
- WARRANTY INFORMATION -
Please register online at http://www.ehx.com/product-registration or complete and
return the enclosed warranty card within 10 days of purchase. Electro-Harmonix will
repair or replace, at its discretion, a product that fails to operate due to defects in
materials or workmanship for a period of one year from date of purchase. This
applies only to original purchasers who have bought their product from an authorized
Electro-Harmonix retailer. Repaired or replaced units will then be warranted for the
unexpired portion of the original warranty term. If you should need to return your
unit for service within the warranty period, please include a brief description of the
problem as well as you name, address, telephone number, copy of your receipt, and
a check or money order. The costs for shipping and handling are listed below.
United States - $12
Canada - $15
Europe and other countries - $25
Ship to:
Electro-Harmonix
C/O New Sensor Corporation
55-01 2nd Street
Long Island City, NY 11101
Attn: Service Department
Please make checks/money orders payable to New Sensor Corporation.
To hear demos on all EH pedals visit us on the web at www.ehx.com.
