Ekwb EK-Vector RTX 2080 Backplate Guía

All disclosures, notices and warranty conditions are being written on the back of the box.

Installation and mounting manual for EK-Vector RTX 2080 Backplate

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

STEP 1: GENERAL INFORMATION. Sample picture of NVIDIA GeForce RTX 2080 graphics card.

STEP 2: PREPARING YOUR GRAPHICS CARD

EK-Vector RTX 2080 is very easy to install. First install EK-Vector RTX 2080 series water block according to its installation manual. If you have it already

installed, please check the picture below to see which mounting screws are to be left in their position and which are to be removed. Please remove the six

(6) M2.5x4 AX1 screws and their PVC washers as well (marked with arrow).

STEP 3: APPLYING THE THERMAL PADS

EK-Vector RTX 2080 features passive cooling of the printed circuit board and its components therefore it is mandatory to install the enclosed

thermal pads. Please install enclosed 1,5mm thick thermal pad (Thermal Pad F –1,5mm (120x16)) and Thermal Pad F –1,0mm (120x16)) as

shown on the picture below. You may need to trim the excess thermal pad.

Thermal Pad F 1.5mm

Thermal Pad F 1.0mm

All disclosures, notices and warranty conditions are being written on the back of the box.

STEP 4: ATTACHING EK-Vector RTX 2080 TO THE GRAPHICS CARD

Take enclosed mounting screws and install them as shown on picture below. Use six (6) M2.5x7 AX1 screws, and tighten them using Philips head screwdriver.

HINT: Do not tighten screws until they are all positioned in their mounting holes. The backplate has milled in standoffs, so there is no fear of over tightening of

the screws. Nevertheless do not exaggerate with screwing force as there is no need for it.

By all means users must also consider that this product is intended to be used only with EK-Vector RTX 2080 series water blocks. No other 3rd party heat sinks

or coolers are officially supported! EK does not offer any assistance or support in the latter application.

IMPORTANT DISCLOSURES

VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the

computer. We recommend a 24 hour leak test prior to powering up the computer. Do not test the water block using city water pressure. This will rupture the top

of the housing and render the block unusable (and will void your warranty).While all efforts have been made to provide the most comprehensive tutorial possible,

EK Water Blocks assumes no liability expressed or implied for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks

cooling products, either due to errors or omissions on our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.

WARRANTY:

Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During

this period, products will be repaired or have parts replaced at our discretion provided that: (I) the product is returned to the agent from whom it was purchased;

(II) the product has been purchased by an end user and has not used for commercial purposes; (III) the product has not been misused, handled carelessly, or

used in a manner other than in accordance with the instructions provided describing its installation and proper use. This warranty does not confer rights other

than those expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not

affect your statutory rights as a consumer. This warranty is voided if the product comes in contact with aggressive UV additives or other improper liquids.

EK blocks are sealed with warranty void circular label, which proves that the block has withstood a pressure leak test. Removing it will void leak-free guarantee

and not the guarantee on the product itself. Any other RMA issues can be reported to EK Support at http://www.ekwb.com/support for further analysis.

REQUIRED TOOLS AND MOUNTING SCREWS:

Philips head screwdriver scissors

M2.5x7 AX1

Tabla de contenidos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-PRO GPU WB RTX 30x0 Manual de usuario

ekwb

ekwb EK-Vector RTX Aorus 2080Ti Manual de usuario

ekwb

ekwb EK-Pro RTX A5500 Rack - Ni+Inox Manual de usuario

ekwb

ekwb EK-Vector Radeon RX5700 + XT Backplate Manual de usuario

ekwb

ekwb EK-FC R9-390X TF5 Series Manual

ekwb

ekwb EK-FC 5870 MSI Manual

ekwb

ekwb EK-FC 780 GTX Lightning Manual

ekwb

ekwb EK-FC980 GTX Ti Classy KPE Manual

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Manual de usuario

ekwb

ekwb EK-FC 5870 V2 Manual

ekwb

ekwb EK-Quantum Momentum Aorus X570 Master D-RGB -... Manual de usuario

ekwb

ekwb EK-Quantum Vector XC3 RTX 3080 D-RGB Manual de usuario

ekwb

ekwb EK-Loop Fan FPT 120 FAN Manual de usuario

ekwb

ekwb EK-RAM Dominator Manual

ekwb

ekwb EK-FC7970 Manual

ekwb

ekwb EK-FC1080 GTX Backplate Guía

ekwb

ekwb EK-FCQK5000 Manual

ekwb

ekwb EK-FC 770 GTX DCII Manual

ekwb

ekwb EK-PRO GPU WB RTX 6000 ADA Nickel Inox Manual de usuario

ekwb

ekwb EK-FC1080 GTX G1 Manual de usuario

ekwb

ekwb ASUS Z9PE-D8 Manual de usuario

ekwb

ekwb EK-FB KIT GA-X99 SOC Champion Series Manual

ekwb

ekwb Classic D-RGB S240 Manual de usuario

ekwb

ekwb EK-Annihilator Pro ILM Series Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-Vector RTX 2080 Backplate Guía

Manuales populares de Hardware de computadora de otras marcas