Ekwb EK-FC WX9100 PRO BACKPLATE Manual de usuario

INSTALLATION MANUAL

EK-FC

WX9100 PRO

GPU WATER BLOCK

- 2 -

This product is compatible with Radeon Pro WX 9100 graphics card.

It is intended for installation only by expert users. Please consult with

a qualiﬁed technician for installation. Improper installation may result

in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor

their installation. The following instructions are subject to change

without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice,

disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic

guidelines:

Please carefully read the manual throughly before beginning

with the installation process!

Please remove your graphics card from computer to assure

safest mounting process in order to prevent any possible

damages to your GPU and/or graphics card circuit board(PCB).

The EK ﬁttings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

Do not use pure distilled water! For best results EK recommends

the use of EK-CyroFuel coolants!

- 3 -

TABLE OF CONTENT

PREPARING YOUR GRAPHICS CARD 4

INSTALLING THE WATER BLOCK 6

CHECKING FOR CONTACTS 8

INSTALLATION OF FITTINGS AND TUBING 8

INSERTING THE CARD IN YOUR PC CASE 9

REQUIRED TOOLS 9

SUPPORT AND SERVICE 10

SOCIAL MEDIA 10

- 4 -

PREPARING YOUR GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

Remove all encircled screws using Phillips screwdriver. All heat sink

assembly screws should be removed, including self-adhesive washers

on both sides of the PCB(if present). Also remove the IO bracket.

STEP 1

STEP 2

CLEANING THE PCB

Carefully detach the original stock cooler after removing all screws

securing in to the board. Wipe off the remains (by using nonabrasive

cloth or q-tip, as shown on sample photo) of the original thermal

compound until the components and circuit board are completely

clean. EKWB recommends the use of denatured alcohol for removing

TIM leftovers.

STEP 2

- 5 -

STEP 3

APPLYING THERMAL COMPOUND

Lightly cover AMD GPU chip with enclosed EK-TIM Ectotherm

thermal grease. EKWB recommends to apply the thermal grease in a

cross form to best performance (see sample picture).

STEP 4

CUTTING THERMAL PADS

Your block is supplied with thermal pads that need to be cut into smaller

pieces in order to cover all VRM components. PLEASE REMOVE THE

PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR

TO INSTALLATION.

Replacement thermal pads:

1. Thermal Pad G 1.0 mm – (120 x 24 mm) – (EAN: 3830046996770)

2. Thermal Pad G 0.5 mm – (120 x 24 mm) – (EAN: 3830046996763)

STEP 5

PLACING THERMAL PADS ON PCB

Once cut to size the thermal pads should be applied to the PCB as

illustrated below. EK made sure to provide customers with more than

adequate quantity of thermal pads to complete this step.

STEP 3

Thermal pad G – 1.0 mm

120

STEP 4

STEP 5

Thermal pad G – 0.5 mm

120

G 0.5 mm

G 1.0 mm

- 6 -

INSTALLING THE WATER BLOCK

STEP 1

PLACING THE BLOCK ON TO THE GRAPHICS CARD

Carefully position the water block with preinstalled standoffs on to

the graphics card. During this process please make sure you align

mounting holes on the PCB with holes on the water block (same

applies for other tops). Also pay attention not to use too much

force by pressing the block down to the PCB. Chip dies are prone

to cracking.

STEP 1

M2.5 x 6 AX1

13 pcs

M 2.5 PVC washer

16 pcs

M2.5 x 4 AX1

16 pcs

M2.5 x 8 AX1

2 pcs

M3 x 4 DIN7985

2 pcs

EK Plug G1/4

2 pcs

2.5 mm Allen Key

1 pc

6 mm Allen Key

1 pc

BAG CONTENT

Bag content is universal for all water blocks, you may not need all screws.

M2.5 Helix nuts

6 pcs

Thermal Grease

1 pcs

- 7 -

STEP 2

ATTACHING THE BLOCK TO THE GRAPHIC CARD

Use a Phillips screwdriver with the enclosed M2.5X4 and M2.5X6

screws. EKWB recommends users to start tightening the screws

around the GPU core and continue outwards. Always use a plastic

washer under each and every screw.

STEP 2

M2.5x4 Screw

Plastic Washer

M 2.5 PVC washer

15 pcs

Phillips-head

screwdriver

M2.5 x 6 AX1

4 pcs

M2.5 x 4 AX1

11 pcs

M2.5x6 Screws

- 8 -

INSTALLATION OF FITTINGS AND TUBING

STEP 1

Screw in the two G1/4 threaded male ﬁttings. Attach the liquid

cooling tubes and connect the water-block(s) into the cooling circuit.

EKWB recommends using EK- ﬁttings.

You can use any opening as an inlet/outlet port. Do not forget to

plug the remaining two opening with enclosed EK-Plug G1/4 or

equivalent.

CAUTION: In case of using connectors other than EK- series

compression ﬁttings, take special attention to the length of the

ﬁttings’ male G1/4” thread. 5mm is the maximum allowed G1/4”

thread length!

STEP 1

Tubing

EK- Plug G1/4

EK-Fitting

CHECKING FOR CONTACTS

If necessary temporarily remove the water block to check for uniform

surface contact between the block and the components, pay special

attention to the VRM section of the graphics card. Check whether

the water block makes contact with the intended integrated circuit.

Then repeat sub-steps in previous section to re-attach the block.

In case you fail to obtain good contact, please check again that

your thermal pad thickness or contact our support service at

http://www.ekwb.com/support.

- 9 -

INSERTING THE CARD IN YOUR PC CASE

Carefully lift your graphics card with installed block and insert it in

your PC’s motherboard PCI express expansion slot. Please bear in

mind that your graphics card is probably heavier than when it was

equipped with original heat sink fan assembly. One needs to be

very careful when handling the graphics card. Avoid all un-needed

manipulation of the VGA/water block assembly that might damage

your card or water block during ﬁnal installation.

Phillips-head Screwdriver Scissors

REQUIRED TOOLS

For assistance please contact:

http://support.ekwb.com/

EKWB d.o.o.

Pod lipami 18

1218 Komenda

Slovenia - EU

EKWaterBlocks

@EKWaterBlocks

ekwaterblocks

EKWBofﬁcial

SUPPORT AND SERVICE

SOCIAL MEDIA

Otros manuales para EK-FC WX9100 PRO BACKPLATE

Tabla de contenidos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-FC5x0 GW GTX water block Manual

ekwb

ekwb EK-FC1080 GTX Backplate Guía

ekwb

ekwb EK-Classic Pump Reservoir 160 SPC PWM D-RGB Guía

ekwb

ekwb EK-FB KIT GA Z97X-SOC Force Guía

ekwb

ekwb EK-Quantum Momentum Aorus Z490 Master D-RGB Manual de usuario

ekwb

ekwb EK-FC RX-480 Manual de usuario

ekwb

ekwb EK-FC R9-290X Lightning Series Manual

ekwb

ekwb EK-FC 4890 VAPOR X Guía

ekwb

ekwb EK-FC980 GTX Ti TF5 Series Manual

ekwb

ekwb EK-FB MSI X299 GAMING PRO CARBON Monoblock Manual de usuario

ekwb

ekwb EK-Pro GPU WB RTX 4000 - Ni + Inox Manual de usuario

ekwb

ekwb EK-FC980 GTX Ti WF3 Manual

ekwb

ekwb EK-Nucleus AIO CR360 Lux D-RGB Manual de usuario

ekwb

ekwb EK-PRO GPU WB RTX A4090 Manual de usuario

ekwb

ekwb EK-FB ASR Z77 Extreme11 Guía

ekwb

ekwb EK-Quantum Vector Trio RTX 2080 Ti Manual de usuario

ekwb

ekwb EK-Quantum Vector FE RTX 3080 Manual de usuario

ekwb

ekwb EK-Supremacy Classic RGB Manual de usuario

ekwb

ekwb EK-FB ASUS M5E Guía

ekwb

ekwb EK-Pro GPU WB RTX 8000 - Ni + Inox Manual de usuario

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

ekwb

ekwb EK-FB MSI X370 XPower Monoblock Manual de usuario

ekwb

ekwb EK-Vector Trio RTX 2080 Manual de usuario

ekwb

ekwb EK-FB MSI X399 GAMING RGB Monoblock Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-FC WX9100 PRO BACKPLATE Manual de usuario

Manuales populares de Hardware de computadora de otras marcas