Ei Electronics Ei166R Manual de usuario

The Smoke/Heat Alarm is mounted on the EI 127 & EI 127R.

The EI 127 pattress facilitates installation of bulky wiring and conduits.

The EI 127R has an additional socket for connecting to the R spade termi-

nal on the EI161R or EI 166R. This can be used for remote test & hush or

manual call points.

WARNING: This pattress must only be used with one of the above smoke

alarms as per these instructions - otherwise the unit will not comply with

the mandatory safety regulations.

WARNING: First disconnect the mains from the circuit to be used.

1.Choose a mounting position following the siting instructions in the

Smoke/Heat Alarm leaflet. Where the incoming wiring is on the surface of

the ceiling, the appropriately sized ducting/conduit must be chosen to

mate with the unit. Use a sharp knife to remove material from the selected

knockout, making sure that there is no gap when mated with ducting / con-

duit. There are three knockouts – two on the sidewall and one on the rear.

Installation

Pattress Models EI 127 & EI 127R

For use only with EI 140, 141, 144, 145, 146, 161, 161R,

164, 166, 166R Easi-Fit Smoke/Heat Alarms

Professional

CONDUIT

CONNECT TO SMOKE ALARM

MOUNTING PLATE TERMINALS

FOR EI161R/166R

REMOTE CONTROL ONLY

KNOCKOUT

FOR MOUNTING PLATE

- EARTH (IF PRESENT)

- NEUTRAL

- INTERCONNECT

-LIVE

KNOCKOUT

Figure 1

2.Screw the pattress to the ceiling after first removing the required knock-

out and bringing the house wires through it (see figure 1). If the central

knockout is being used, seal around the wires (and the openings at the

rear of the pattress) with silicone or similar to prevent air draughts affecting

the smoke entering the alarm.

3.Connect the house wires (L - Live, N - Neutral and IC - Interconnect, if it is

being used) to the terminal block on the pattress. If an EI 161R or EI 166R

(with remote TEST/HUSH) is being installed, attach the “R” wire from the

EI 152 (see the EI 152 instructions) to the terminal marked “R” in the

pattress (see figure 1). If the EI 161R or EI 166R is being used with a man-

ual call point MCP400 or MCP400A then connect the R terminal to the call

point (see figures 1& 2). Otherwise do not connect anything to the ”R” ter-

minal.

4.Connect the three wires (L, N and IC) from the pattress connector block

to the connectors on the Smoke/Heat Alarms mounting plate. Connect the

earth wire (if present) from the house wiring directly to the terminal on the

mounting plate. Replace the cover over the terminal wires.

5.Screw the mounting plate to the pattress pillars using the two screws

supplied.

6.Slide the alarm on to the mounting plate.

7.Connect the mains power – the green LED light on the alarm should be

on. When the test button is pressed the horn should sound.

If an EI 128R pattress with relay is being used, replace the EI 127R with the

EI 128R and follow the instructions supplied with the EI 128R.

Aico Ltd., Mile End Business Park, Maesbury Road, Oswestry,

Shropshire SY10 8NN, U.K.

EI Electronics., Shannon Industrial Estate, Shannon, Co. Clare.

R - Remote

N - Neutral

IC - Interconnect

L - Live

Smoke Alarm

EI 161R or EI 166R

EI 152 Manual Call Point

MCP 400

(or MCP 400A)

Pattress

EI 127R/128R

Mounting

Plate

EI 16XR

Figure 2

P/N A13894 Rev 1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Detector de humo de Ei Electronics

Ei Electronics

Ei Electronics Ei603 Series Manual de usuario

Ei Electronics

Ei Electronics Ei605 Series Manual de usuario

Ei Electronics

Ei Electronics Ei141 Ionisation Manual de usuario

Ei Electronics

Ei Electronics Ei 151TLR Ionisation Manual de usuario

Ei Electronics

Ei Electronics Ei151TL Instrucciones de instalación

Ei Electronics

Ei Electronics Ei 100TYC Ionisation Manual de usuario

Ei Electronics

Ei Electronics aico Ei146e Manual de usuario

Ei Electronics

Ei Electronics Ei154TL Manual de usuario

Ei Electronics

Ei Electronics Ei161RC Ionisation Manual de usuario

Ei Electronics

Ei Electronics Ei 175 Ionisation Manual de usuario

Ei Electronics

Ei Electronics Ei160e Series Manual de usuario

Ei Electronics

Ei Electronics Ei 100R Ionisation Manual de usuario

Ei Electronics

Ei Electronics Easichange Series Manual de usuario

Ei Electronics

Ei Electronics Ei100BNX Manual

Ei Electronics

Ei Electronics Ei146 Optical Manual de usuario

Ei Electronics

Ei Electronics Ei175 Ionisation Manual de usuario

Ei Electronics

Ei Electronics RadioLINK Ei170RF Manual de usuario

Ei Electronics

Ei Electronics Ei128R Manual de usuario

Ei Electronics

Ei Electronics Ei603CRF Manual de usuario

Ei Electronics

Ei Electronics EIB140RC Series Manual de usuario

Ei Electronics

Ei Electronics Ei3024 Manual de usuario

Ei Electronics

Ei Electronics MCP401RC Manual de usuario

Ei Electronics

Ei Electronics EI 100C Interconnect Manual de usuario

Ei Electronics

Ei Electronics Ei141 Ionisation Manual de usuario

Manuales populares de Detector de humo de otras marcas

x-sense

x-sense SD19-W Manual de usuario

BRK electronic

BRK electronic First Alert P1010 Manual de usuario

FireAngel

FireAngel Thermoptek ST-622 Manual de usuario

teko

teko Astra-42A Manual de usuario

Safetec

Safetec SDS-2/6 Manual del propietario

Siemens

Siemens PE-11C Manual de usuario

System Sensor

System Sensor DH500ACDC Manual de usuario

Resolution Products

Resolution Products RE612 CryptiX Manual de usuario

First Alert

First Alert PC900V Manual de usuario

Eminent

Eminent EM6590 E-Domotica Manual de usuario

Carrier

Carrier Kidde Quell Q301 Manual de usuario

VESDA

VESDA VLF-500 Manual de usuario

ELRO

ELRO FS8110 Manual de usuario

Heiman

Heiman SMOKI NS-626PHS Manual de usuario

Regin

Regin SDD-S65 Manual de usuario

Family Gard

Family Gard FG225 Manual de usuario

Greystone

Greystone DSD120 Manual de usuario

Aparton

Aparton ASD-10 Manual de usuario