EGig XW305K Manual de usuario
5 Port Nway Fast Ethernet Switch
User's Manual
1234
5
POWER
LINK/ACT
10/100M
FDX
UP-LINK
12345
5
FCC Warning
This device has been tested and found to comply with limits for
a Class B digital device, pursuant to Part 2 and 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses and radiates radio frequency energy and, if
not installed and used in accordance with the user's manual,
may cause interference in which case user will be required to
correct the interference at his own expense.
CE Mark Warning
This is a Class B product. In a domestic environment, this
product may cause radio interference in which case the user
may be required to take adequate measures.
Table Of Contents
Chapter 1 -------------------------------------------------------------------1
Introduction---------------------------------------------------------------------1
KeyFeatures-------------------------------------------------------------------2
Chapter 2 -------------------------------------------------------------------3
PackageContents------------------------------------------------------------3
Chapter 3 -------------------------------------------------------------------4
Front Panel Layout -----------------------------------------------------------4
5 RJ-45 10/100Mbps Switch Ports ---------------------------------4
Uplink port----------------------------------------------------------------4
LED Indicators of 5 Port 10/100Mbps Switch---------------5
LED Definitions ----------------------------------------------------------6
Power LED --------------------------------------------------------------6
FDX LED -----------------------------------------------------------------6
10/100M LED -----------------------------------------------------------6
LINK/ACT LED ---------------------------------------------------------6
Rear Panel Layout ----------------------------------------------------------6
AC input---------------------------------------------------------------------6
Chapter 4 -------------------------------------------------------------------7
Installation ----------------------------------------------------------------------7
ToconnecttheSwitchtoPCs,servers,andother
network devices.---------------------------------------------------------7
To connect the Switch to a Switch or a Hub ----------------------7
Chapter 5 -----------------------------------------------------------------8
Technical Specifications ----------------------------------------------------8
I.
II.
III.
IV.
I.
II.
Chapter 1
5 Port Nway Fast Ethernet Switch
Introduction
The Switch provides 5 10/100Mbps ports. The Switch was designed
for easy installation and high performance in an environment where
traffic on the network and the number of user increase continuously.
The compact rigid desktop size was specifically designed for ROBO
(Remote Office & Branch Office) and small to medium workgroups.
The Switch can be installed where space is limited; moreover it
provides smooth network migration and easy upgrade to network
capacity.
-1-
1234
5
POWER
LINK/ACT
10/100M
FDX
UP-LINK
12345
5
Key Features
5 Port 10/100BASE T/TX Nway (Auto-negotiation)
Switch with RJ-45 connectors
Desktop size with compact rigid design
Auto-detect of Full/Half-duplex modes in all ports
Dedicated full-duplex 200Mbps bandwidth on each
port
Broadcast storm control
Store & Forward switching methods
IEEE 802.3x flow control for Full-duplex
Zero-Packet Loss Back-pressure flow control for
Half-duplex
Non-blocking & Non-head-of-line blocking full wire
speed forwarding
Auto-learning of networking configurations
Status LEDs: Power, Speed, Link/Activity And
Full/Half-duplex
Smart plug & play
-2-
Chapter 2
Package Contents
Before you start to install the Switch, please verify your package that
contains the following items:
One Fast Ethernet Switch
One Power Cord
One User's Manual
Note: If any of these items is found missing or damaged, please
contact your local supplier for replacement.
-3-
5 Port Nway Fast Ethernet Switch
User's Manual
5 Port Switch
Power Cord
User's Manual
1234
5
POWER
LINK/ACT
10/100M
FDX UP-LINK
12345
5
1234
5
POWER
LINK/ACT
10/100M
FDX
UP-LINK
12345
5
Chapter 3
Front Panel Layout
I. 5 RJ-45 10/100Mbps Switch Ports
There are 1~5 RJ-45 connectors on the front panel for connecting to
servers, workstation or other devices. The Switch provides 5
10/100Mbps switching ports that could sense the 10/100M speed
and negotiate Full/Half-duplex mode automatically. These switching
ports allow users to connect the Switch to 10BASE-T and 100BASE-
TX devices.
II. Uplink Port
Uplink port shared with the port #1 for expanding to another Hub or
Switch. The Uplink port and port 1 share the same port & function.
Do not use both of the Uplink port and port 1 at the same time.
-4-
Uplink Port
RJ-45 Port
LED Display
5UP-LINK
UP-LINK
UP-LINK
III. LED Indicators of 8 Port 10/100Mps Switch
LED Color Status Description No. Of LED
Power Yellow On Power on 1
FDX Green On Full-duplex 5(1~5)
Off Half-duplex 5(1~5)
Flashing Partial collision 5(1~5)
occurs
10/100M Green On Port is on the 5(1~5)
100M status
Off Port is on the 5(1~5)
10M status
LINK/ACT Yellow On 10/100Mbps port 5(1~5)
for connection
Flashing 10/100Mbps for 5(1~5)
data activating
-5-
Yellow
Ethernet Switch
Yellow
Green
Green
LINK / ACT
POWER
10 / 100M
FDX
1 2 3 4 5
5
VI. LED Definitions
Power LED
On : The unit is powered on and ready for use.
Off : The unit is powered off.
FDX
On : The port is operating at Full-duplex.
Off
Flashing : Collisions occurred and the port is
operating at Half-duplex mode.
10/100M LED
On : The port is on the 100Mbps status.
Off : The port is on the 10Mbps status.
LINK/ACT LED
On : The port is ready for 10/100Mbps
connection
Flashing : The data is transmitted or received on
the port.
Rear Panel Layout
AC input
AC input (100~240V/AC, 50~60Hz) UL Safety
-6-
: The port is operating at Half-duplex
without any data being transmitted or
received.
AC LINE
100~240VAC
50~60Hz, 1A
Chapter 5
Installation
I.To connect the Switch to PCs, servers, and other network
devices.
Use straight-through twisted-pair cable (Cat. 5) to connect the Switch
to PCs, servers and other network devices. Networks can be build
as figure shown
II. To connect the Switch to a Switch or a Hub
Use straight-through twisted pair cable to connect the Switch to
another Switch or Hub on uplink port. If you connect the Switches on
port 1 to port 5, the cable should be changed to crossover cable.
-7-
1234
Dual Speed Hub
Uplink
Uplink
Uplink
Fast Ethernet Switch
Fast Ethernet Switch
PC
PC
PC PC PC
MAC
Server
Server
Workstation
PC MAC
Server
Workstation
1234
5
POWER
LINK/ACT
10/100M
FDX
UP-LINK
12345
5
1234
5
POWER
LINK/ACT
10/100M
FDX
UP-LINK
12345
5
Tabla de contenidos
Otros manuales de Enrutador de red de EGig
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad