Edimax ES-5800D+ Manual de usuario

Gigabit Smart

Switch

8 Ports 1000/100/10Mbps

ES-5800D+

ES-5800R+

User’s Manual

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the

limits of a Class A computing devices, pursuant to Part 15 of the

FCC rules. These limits are designed to provide reasonable

protection against harmful interference. This equipment

generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

If you suspect this product is causing interference, turn your

computer on and off while your radio or TV is showing

interference. If the interference disappears then when you turn

the computer off and reappears then you turn the computer on,

something in the computer is causing interference.

You can try to correct the interference by one or more of the

following measures:

1. Reorient/relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit difference

from that to which the receiver is connected.

4. Ensure that all expansion slots (on the back or side of the

computer) are covered. Also ensure that all metal retaining

brackets are tightly attached to the computer.

Content

1. Introduction ........................................ 3

2. Features & Specifications ..................4

3. Package Contents................................ 6

4. Hardware Description........................7

5. Advance Smart Function Setting .... 9

5.1 Login Page .............................. 11

5.2 Top Screen............................... 12

5.3 Port Status...............................13

5.4 Port Configuration................. 14

5.5 Mirror Port Configuration.... 15

5.6 VLAN Configuration.............16

5.7 Trunk Configuration..............17

5.8 MISC Configuration..............18

5.9 Set Password...........................19

6. Troubleshooting................................ 21

1. Introduction

Congratulations on your purchase of this eight ports Gigabit

Smart Switch. This high performance Gigabit switch provides

eight 1000/100/10Mbps Gigabit Ports to allow simultaneous

transmission of multiple packets via an internal high-speed data

channel.

The built in console interface can be used to configure

the switch’s settings for priority queuing, VLAN,

Trunking, Port Monitoring and Port speed.

This Gigabit switch utilizes store-and-forward switching

architecture that filters and forwards data after the complete data

packet is received and examined to be free of errors. The front

panel of this switch provides LEDs for easy recognition of the

switch operation status and for troubleshooting.

All the Gigabit ports support both Full and Half duplex which

are able to provide up to 2000Mbps of bandwidth to the

connected devices, with auto-negotiation providing the

capability to connect to 1000/100/10Mbps network devices. It

also supports backpressure and IEEE 802.3x advanced flow

control capabilities that can reduce congestion and prevent

packet loss.

In addition, all the ports support the MDI/MDI-X auto-detect

function. That is to say, you can connect any device (including

PC, Switch, Hub) to a port of this switch using a regular cable.

The RJ-45 port will auto-detect and auto-switch to the correct

MDI/MDI-X mode (do not need to use a specific uplink port or

cross-over cable).

2. Features & Specifications

Features

 Complies with the IEEE802.3 Ethernet, IEEE802.3u Fast

Ethernet and IEEE 802.3ab Gigabit Ethernet Standards

(gigabit over copper)

 Provides Store-and-Forward architecture and full wire

speed filtering and forwarding rate

 Provides eight 10/100/1000Mbps Gigabit switching ports

(RJ-45 connector)

 All ports provide Auto-Negotiation and Auto-MDI/MDI-X

functions

 Supports flow control: Back pressure for Half-duplex and

IEEE 802.3x for Full-duplex mode

 Supports Port-based VLAN(up to 8 groups)

 Supports QoS(IEEE 802.1p)：4 Priority queues per port

 Supports Port Mirroring

 Supports Console configuration

 Desktop : 11” compact size designed

Rackmount : 19” rackmount size designed

Specifications

 Standards: IEEE802.3 10BaseT, IEEE802.3u 100BaseTX

and IEEE802.3ab 1000BaseT copper over Ethernet

 Total Ports: 8 10/100/1000Mbps auto-sensing Fast

Ethernet/Gigabit Ethernet ports

 Media Interface: RJ-45

 Forwarding Method: Store-and-Forward

 MAC Address: 8K

 Buffer Memory: 256KBytes

 Flow control: Back pressure for half-duplex and

IEEE802.3x for full-duplex

 Advance configuration functions:

VLAN setting: Port-based VLAN up to 8 groups

Trunking: Up to 2 trunking groups

Priority Queuing (CoS) setting

Port Mirroring

 Auto-negotiation: All ports

 Auto MDI/MDIX function: All ports

 System LED indication: Power

 Port LED indication:

FULL/COL: Full duplex / Collision

Speed: 10/100/1000Mbps

LNK/ACT: Link / Activity

 Operation Temperature: 50~131℉(10~55℃)

 Operation Humidity: 10~95% (Non-condensing)

 Power: 100~240VAC, full range internal power supply

 Emission: FCC Class A, CE, C-Tick

3. Package Contents

Packing list

Check the contents of your package for following parts:

 One Gigabit Switch

 One User's manual

 One Power cord

 One RS-232 Cable

If any of the items are missing or damaged, please

contact your local dealer.

Console123 8

8 Port Gigabit Smart Switch 1000/100/10Mbps

1234

Power LNK/ACT

Speed 1000M: Yellow

100M :Green

Full/Col

10M :OFF 4567

5678

4. Hardware Description

This section describes the hardware features of this Gigabit

Smart Switch. For easier management and control of the switch,

familiarize yourself with its display indicators and ports. All

LEDs are located on the front panel of the switch. They serve

the purpose of monitoring the operation and performance of the

switch at a glance.

 LED indicators

FULL/COLFULL: ON

COL: Blink

LNK/ACT LNK: ON

ACT: Blin

SPEED

1000M:Yellow

100M:Green

10M:OFF

1234

Power LNK/ACT

Speed 1000M: Yellow

100M :Green

Full/Col

10M :OFF

5678

Operating Environment

This switch must be installed and operated within the limits of

the specified operating temperature and humidity (see previous

section on Specifications). Do not place objects on top of the

unit or obstruct any vents at the sides of the unit. Do not position

the unit near any heating source such as heaters, radiators, or

direct exposure to sun. Do not expose the unit to water and or

moisture. If necessary, use a dehumidifier to reduce humidity.

Connecting to network devices

1. All ports of this switch support the Auto-MDI/MDI-X

function. That is to say, you can connect any device

(including PC, Switch, Hub) to a port of this switch using a

regular cable. The RJ-45 port will auto-detect and

auto-switch to the correct MDI/MDI-X mode. (do not need

to connect to a specific uplink port or cross-over cable)

2. Connect one end of the network cable to the RJ-45 port on

the front panel, and connect the other end of the network

cable to the RJ-45 port on the network device. Follow the

same procedure to connect all the RJ-45 ports of the switch.

Maximum length, using UTP cable, between the switch and

connected device is 100 meters (300ft). Once the network

cable is connected to both ends and the attached network

device is powered on, the LNK/ACT LED should be lit.

3. Make sure the wiring is correct. You need to use Category

3/4/5 cable for 10Mbps operation or Category 5 cable for

100Mbps and Gigabit (1000Mbps) connections.

Connecting the power

Plug the power cable into the internal three pronged power plug,

and connect it to an electrical outlet.

5. Advance Smart-Function Setting

This switch provides advance features, which offers you more

flexibility in setting up your network. The following section

explains how to set up the VLAN, Trunking, Speed, Port

Mirror, Full/Half duplex and QoS modes.

Before using advance Configuration

Connect to PC

Attach a RS-232 serial cable 9-pin male connector to the

female connector on the switch. Plug the other side of this

cable to your PC.

Using Hyper Terminal to connect to Switch

In MS-Windows, launch “Hyper Terminal”, create a new

connection, and follow these steps:

1. Open the HyperTerminal application

2. In Windows, select run from the start menu and choose the

application.

3. From the HyperTerminal menu, double click the icon and

create a new name on the next window, such as Gigabit

Smart Switch.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Edimax

Edimax

Edimax EK-PA2C Manual de usuario

Edimax

Edimax SP-1101W Manual de usuario

Edimax

Edimax GS-5008E Manual de usuario

Edimax

Edimax Hub Manual de usuario

Edimax

Edimax ES-5824P Manual de usuario

Edimax

Edimax EU-4230 Manual de usuario

Edimax

Edimax ES-5160G+ Manual de usuario

Edimax

Edimax EU-HB4S Manual de usuario

Edimax

Edimax ES-5224RM+ Manual de usuario

Edimax

Edimax ES-3124RE+ Manual de usuario

Edimax

Edimax GS-1026 Manual de usuario

Edimax

Edimax ES-1008P Manual de usuario

Edimax

Edimax 5/8 Ports Desktop Manual de usuario

Edimax

Edimax EK-16RE Hoja de instrucciones

Edimax

Edimax EU-HB4P Manual de usuario

Edimax

Edimax ES-3105P Manual de usuario

Edimax

Edimax ES-3305P V2 Manual del propietario

Edimax

Edimax EK-UAK4 Manual de usuario

Edimax

Edimax EK-16RE Manual de usuario

Edimax

Edimax EK-PS2P Manual de usuario

Edimax

Edimax EU-HB4M Manual de usuario

Edimax

Edimax EK-082C Manual de usuario

Edimax

Edimax ES-3305P V3 Manual de usuario

Edimax

Edimax EK-16RE Guía de referencia

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario