Edge USB Watch Manual de usuario
3300 Ver3(09-04)
DiskGO!TM USB Watch Drive
This product is backed by a one year limited warranty.
For complete warranty information visit
www.edgetechcorp.com/register.
Introduction
Thank you for purchasing the EDGE DiskGO! USB Watch Drive. We hope you will enjoy the convenience
and flexibility of having your data stored in an everyday wristwatch! This guide explains how to use the
DiskGO! Watch and the Application Software bundled with your device.
SAFETY PRECAUTIONS
Please read the safety precautions carefully before you begin using the DiskGO! Watch and the
application software. Ensure that you use the product correctly according to the procedures outlined in
this guide.
______________________________________________________________
Warning
______________________________________________________________
zDo not attempt to disassemble or alter any part of the product that is not described in this guide.
zDo not handle the product or plug and unplug the device if your hands are wet. Doing so runs the
risk of electrical shock.
zDo not place the product near to or exposed to direct flame or heat.
zNever place the product near equipment generating strong electromagnetic fields. Exposure to
strong magnetic fields may cause malfunctions or corruption of data.
zMake sure the plug is dry before you connect the DiskGO! Watch to a computer. This may result in
a short circuit which might damage your DiskGO! Watch and/or computer.
zAlways hold the USB plug when disconnecting the DiskGO! Watch from your computer. Never
unplug it by only holding the watch or wire as this may damage the DiskGO! Watch.
zIt is recommended that you frequently clean accumulated residue inside the plug to prolong the
product’s life.
Setting the Time
zPull out the crown when the second hand arrives at 12 o’clock position.
zTurn the crown in either direction to set hour and minute.
zPush the crown to the normal position to start
Changing the Watch Battery
Please follow the procedures outlined below:
1. Unscrew the casing on the back of the watch
2. Unscrew the Circuit Board Assembly (CBA)
3. Lift the CBA as shown in the picture
4. Remove the red insulator and replace the battery. Next, replace the red insulator,
screw the CBA back down, and then secure the outer casing.
SYSTEM REQUIREMENTS
The following system requirements must be met to install and operate the DiskGO! Watch and the
application software.
zMacor PC USBequipped IBM PC/ATCompatible,USB
equipped Macintosh computer.
zOperating System (OS) Windows 98 , Windows Millennium Edition (Windows ME), Windows
2000, Windows XP, Linux 2.4 or higher, Mac OS 8.6 or higher
zUSB Interface
z3 MB or more Free Hard Disk Space
1. The software contained on the CD is for Windows based PC’s only. The version for Macintosh
is under development right now. We will release it when available.
2. Windows 98 does not support the default Mass Storage Driver contained in the device. You will
have to install the driver bundled with the DiskGO! Watch. See Section “Installing/Uninstalling
the Application Software” for details.
3. You will not have to install the software on most computers. The DiskGO! Watch can use the
default driver in most cases. However, if you want to run the application software bundled with
the product, you must install the software which will also install additional drivers. This will
ensure the proper function of the application software.
4. The DiskGO! Watch will operate with the basic disk functions supported in the operating
systems listed above.
GUIDE TO COMPONENTS
USB Interface: The interface connects to the USB port of the computer.
LED Display: The LED Display will show the status of the device. When the DiskGO!
Watch is being used, the LED will flash quickly.
BASIC FUNCTIONS
1. Plug and Play
When you plug the device into the USB port of your computer, you will see a “Removable Disk” icon
in the Explorer window.
When using the DiskGO! Watch on a Macintosh using OS 9.0 or higher, once you plug the DiskGO!
Watch into the USB port, you should see the disk icon on the Desktop. If you are using MAC OS 8.6,
you will need to download the necessary USB mass storage driver from Apple’s web site before using
the DiskGO! Watch.
In Linux, you can follow the following instruction to “mount” the device,
．First plug the device into the USB port of your computer
．Execute: cd /etc/sysconfig/ ( cat /etc/sysconfig/hwconf | more )
．Check the device information in hwconf and write down the mount point.
．Make a directory in /mnt (ex: mkdir /mnt/usbHD )
．Then execute: mount /dev/sda1 /mnt/usbHD (if mount point was .dev/sda)
2. Read/Write Capabilties
You can read, write, copy, and delete files and data just like you would on a normal hard disk or
floppy disk. The DiskGO! Watch Drive allows for fast and easy data transfer.
3. Unplugging the Device
When using the DiskGO! Watch with Windows ME, 2000, or XP, you must stop the device using the
“Safe Removal” icon in the system tray.
Double click the “Safe Removal” icon, and the “Unplug or Eject Hardware” window will pop up. You
can select the device you want to remove (USB Mass Storage Device). Then click the “Stop” button.
Shortly after clicking stop, you will get a message indicating that you can unplug the device from the
USB port of your computer.
Warning: When you want to remove the DiskGO! Watch, make sure the LED isn’t flashing.
If the LED is flashing, activity is still occurring between your computer and the DiskGO!
Watch. Do not remove the DiskGO! Watch at this time as it could damage your data or the
DiskGO! Watch.
Warning If you do not follow the Safe Removal procedure in Windows ME, 2000, or XP, it may
cause data loss or the malfunction of the DiskGO! Watch.
If you are using a Macintosh, you can drag the removable disk icon and put into the trash. This will
perform the “Eject” function which will allow you to safely remove the DiskGO! Watch
If you are using Linux, please follow the “un-mount” command procedure to remove the device.
PARTITION TYPES
You can partition the DiskGO! Watch into three types of areas. We will use the following terminologies in
this guide:
1. Public Area There is no “Security” function at all. You can do any basic functions, as
described in the “Basic Functions” section.
2. SecureArea This area cannot be viewed without the application software. Once you log
in using the application software, your view will switch from the “Public
Area” to the “Secure Area”. Once this is done successfully, you can do any
basic functions, described in the “Basic Functions” section.
You can only view either the “Public Area” or “Security Area” in the same
disk logic unit number, LUN.
You can select the following partition combinations:
1. Single Public Area The entire device storage area is accessible
2. Security Area Partition the device into two partitions in the same LUN, Public
Area and Security Area. The Public Area can be accessed by
everybody. The Security Area can be accessed only by using a
password.
3. Public Area Plus Security Area Partition the device into three partitions in two LUNs, Public
Area and Security Area in LUN0, and Public Area in LUN1. The
partition status is shown in the following diagram. The
partitions in LUN 0 will perform as described in the above item
2. The partition in LUN1 will perform as described in the above
item 1.
This figure shows the detail operation of single LUN.
This figure shows the detail operation of multiple LUNs.
Function
Type
Security Password Disk Logical Unit
Number
Disk Letters
in OS
1. Public Area Only No No 1 (LUN0) 1
2. Security Area Yes Yes 1 (LUN0) 1
3. Public Area Plus Security Area Yes Yes 2 (LUN0 & LUN1) 2
This table shows the function description of the three partition types.
Utilizing the Windows Software
Installing/Uninstalling the Application Software:
Security
Area
Security
Area
Public
Area
Change View
Through
Login & Logout
LUN 0
LUN 1
Public
Area
Security
Area
Change View
Through
Login & Logout
LUN 0
If you are using Windows 98, you must install the driver before you install the application software.
Installing the software:
If you are installing the application software for use with Windows XP or 2000, you must first log on to the
computer as “administrator” and then install the application software.
Precautions about the USB Interface
•Please connect the device to the USB port of your computer when you install the application
software.
•If you do not connect the device to the USB port and install the application software in Windows XP,
when you first plug in the device you will have to install the DiskGO! Watch driver again.
•After you install the driver in Windows 98 or Win Me, you will need to unplug the DiskGO! Watch and
plug it again in order to use the correct driver.
1. Find the “UMSDTools2.33.exe” program.
You can find the program in the DiskGO! Watch, CD-ROM, or Floppy.
2. Double-click the icon.
3. Follow the on-screen instructions to proceed.
Uninstalling the software:
To remove the installed software, you can click the [Start] button and select [Settings], [Control Panel]
and [Add/Remove Programs]. The application software can also be uninstalled by clicking the [Start]
menu and selecting [Programs], [UMSD], [Uninstall UMSD].
Notes:
•The USB driver only needs to be installed the first time the DiskGO! Watch is connected via the USB
port.
•Do not cancel the installation during the procedure. The DiskGO! Watch may not operate correctly if
the installation is incomplete.
•Read the “Troubleshooting” Section if the installation cancels, if the installation did not proceed as
described, or if you feel that the drivers are not properly installed.
Installing the USB Driver:
For some Windows system, users should log on as the Administrator before installation. Once you have
attached the DiskGO! Watch to the computer, it will find the appropriate driver or the “Add New Hardware
Wizard” dialog will appear after a moment. You can install the driver manually, or just find the
“UMSDTools2.33.exe” program to do the driver installation.
If the “Digital Signature Not Found” message displays during installation, just click the [Yes] button to
proceed.
Using UMSD.exe Program the First Time:
Warning The UMSD Program can only handle one DiskGO! Watch at a time. If you
are not planning to use the functions of the UMSD Program, like “Resize”,
“Change Password”, or “Log In”, etc., you can insert more than one DiskGO!
Watch Drive. If you want to use advanced functions of the program, please
remove all other DiskGO! Watches. This may cause the UMSD program
perform incorrectly, possibly causing data to be lost.
After you install the software and driver correctly, the UMSD icon will appear in the notification area
automatically.
Or
The icon displayed will depend on the status of the device.
•Right click on the icon to reveal selection menu shown below in the following figure:
•You can also double click the icon in the notification window. The UMSD manager
window will pop up.
•By default, the device is not in “Security” mode, so the “Resize” function will be active
when you run this software for first time.
[UMSD] - Resize:
Warning The “Resize” function will erase all the data or files stored in the DiskGO!
Watch. You cannot stop this process once you begin. It is important that you
backup any important files or data before you use the “Resize” function. Please
close any open programs or windows as well.
1. Click the Resize tab in the UMSD manager window. The following “Resize Partition” window will pop
up.
2. Select the partition type you want.
3. If you select “Public Area Only”, then click the [OK] button. The “Confirmation” window will pop up.
Please make sure you have already backed up any important files or data on the DiskGO! Watch.
4. If you select “Security Area”, you will next see the “Security Area Resize” window pop up. You can
drag the scroll bar in the middle of the window to set the size of the “Public Area” and “Security
Area”, or you can type in the size of each Zone you want in the “Size” window. You can set the
password for accessing the security area in the “New Password” window. The maximum size of the
password is 8 characters. You can also type in a hint for your new password in the “Password Hint”
window. This hint will be displayed when you click the “Hint” button in the “Unlock Protect” window.
The maximum size of the hint is 32 characters. After you have finished, click the [OK] button. The
“Confirmation” window will pop up. Please make sure you have already backed up any important
files or data on the DiskGO! Watch.
5. If you select the “Public Area + Security Area”, then the following “Public/Security Area Resize”
window will pop up. You can drag the scroll bar in the window to set the size of each area. First, set
the size of the “Public Area” of LUN1. The minimum size for each area is 1MB. Once the size of the
“Public Area” of LUN1 is set, the scroll bar of the “Public Area” and “Security Data Zone” of LUN0 will
automatically be set in the middle”, or you can type in the size of each Zone you want in the “Size”
window. You can set the password for accessing the security area in the “New Password” window.
The maximum size of the password is 8 characters. You can also type in a hint for your new
Otros manuales para USB Watch
1
Tabla de contenidos
Manuales populares de Software de otras marcas
PS Audio
PS Audio PowerPlay Manual del propietario
Brady
Brady LOCKOUT PRO 3.0 Manual de servicio
Avaya
Avaya Interaction Center Manual de usuario
Texas Instruments
Texas Instruments TI-83 Plus Silver Edition Manual
Novell
Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario
Oracle
Oracle Application 9i Manual de usuario
Acer
Acer RDM Manual de usuario
Canon
Canon Vixia HF21 Manual de usuario
Canon
Canon ZR950 Manual de usuario
Samsung
Samsung Auto Backup Manual de usuario
Polycom
Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento
Brocade Communications Systems
Brocade Communications Systems Brocade 8/12c Manual de usuario