Edge Technologies V-65 Series Manual de usuario
V-65 Series
SHORT BAR FEEDER
REBEL-V-65E/LE-A
MANUAL FOR USE AND MAINTENANCE
REV. 08 DATE：
：：
：2016/06/01 COD：
：：
：BRV104032
S/H
INDEX V-65E-A
Ⅰ
CONTENT（
（（
（INDEX）
））
）
1 GENERAL INFORMATION
1.1 Contents of the manual -----------------------------------------------------------------
1-1
1.2 The label of manufacturer and bar feeder -----------------------------------------
1-2
1.3 Support of technique --------------------------------------------------------------------
1-2
2 DATA OF TECHNIQUE
2.1 Introduction of the bar feeder ---------------------------------------------------------
2-1
2.2 Machine size ------------------------------------------------------------------------------
2-2
2.3 Description --------------------------------------------------------------------------------
2-2
2.4 Compressed air supply and power supply -----------------------------------------
2-3
3 TRANSPORTATION
3.1 Packing the Feeder ----------------------------------------------------------------------
3-1
3.2 Transportation and hoist ---------------------------------------------------------------
3-2
3.3 Forklift transportation -------------------------------------------------------------------
3-3
3.4 Installation area --------------------------------------------------------------------------
3-5
4 INSTALLATION
4.1 Bar feeder ---------------------------------------------------------------------------------
4-1
4.2 Adjustment of height --------------------------------------------------------------------
4-1
4.3 Initial position -----------------------------------------------------------------------------
4-2
4.4 Directional adjusting --------------------------------------------------------------------
4-3
4.5 Mounting of the feeder frame ---------------------------------------------------------
4-4
4.6 Securing and fastening of the bar feeder ------------------------------------------
4-4
4.7 Accessories installation ----------------------------------------------------------------
4-5
INDEX V-65E-A
Ⅱ
CONTENT（
（（
（INDEX）
））
）
5 ADJUSTMENTS AND SETTING
5.1 Structure of the bar feeder -------------------------------------------------------------
5-1
5.2 Adjustment and selection of the bar feeder ---------------------------------------
5-2
5.3 Adjustment of bar stop -----------------------------------------------------------------
5-2
5.4 Adjustment of bar diameter -----------------------------------------------------------
5-3
5.5 Adjustment of push bar pressure ----------------------------------------------------
5-3
5.6 Selection of push bar -------------------------------------------------------------------
5-4
5.7 Optimizing remnant ---------------------------------------------------------------------
5-5
5.8 Maintain notice-key switch ------------------------------------------------------------
5-6
6 OPERATIONS AND ILLUSTRATIONS
6.1 Material preparation --------------------------------------------------------------------
6-1
6.2 Operation description ------------------------------------------------------------------
6-2
6.3 Description of settings and parameter ---------------------------------------------
6-7
6.4 Refer alarm message ------------------------------------------------------------------
6-23
7 ELECTRICAL CIRCUIT DIAGRAM
8 PARTS LIST
1. GENERAL INFORMATION V-65E-A
1-1
1. GENERAL INFORMATION
Please read the Manual carefully before operating bar feeder.
1.1 Contents of the manual
The feeder manufacturer provides this manual, which is an essential part of the
integrated products. Please act according to the indication of the manual in order
to assure operators’ safety as well as the machines’, and greatly achieve
economic efficiency and to get the best output of the machine’s capability. The
important part is printed in boldface, and included the following marks:
Warning：
：：
：
Hazard! It is possible to hurt you seriously, please be careful.
Watch out-Precautions：
：：
：
For preventing the accident or the loss of property, you should take precautions.
Important information：
：：
：
Special important know-how information
Please take use of the table of contents, you will quickly find the information you
need.
The mark shown in the manual means that the machine should be operated by a
qualified and expert operator. As to the other operation shall be handled by a
qualified personnel or professional operator of bar feeder.
1. GENERAL INFORMATION V-65E-A
1-2
1.2 The label of manufacturer and bar feeder
A. Name of manufacturer
B. Model(Type)
C. Serial Number
D. Manufacture Date
E. Weight of Machine
F. Pneumatic Pressure
G. Rated Voltage
H. Control Voltage
I. Full Load Current
J. Power
K. Short Circuit Rating
L. Wiring Drawing Number
1.3 Support of technique
If you need any support of technique, you can inquire the service center in the
appendix at anytime.
INFORMATION：
：：
：
When you need the support of technique, please refer to the label on the bar
feeder. Tell us the data of the bar feeder.
2. DATA OF TECHNIQUE V-65E-A
2-1
2. DATA OF TECHNIQUE
2.1 Introduction of the bar feeder
The V-65E/LE-A is designed for full automatic lathe to auto feeds material, the bar
feeder is suitable for digital control sliding headstock lathe and fixed headstock
lathe. The program of the P.L.C system can control the bar feeder running with the
lathe at the same time. Operator can set parameters by the interface of man
machine directly.
The remote control box is easily to be operated.
The bar feeder can feed circular material and any other forms of material. While
the lathe is running, the guide channel is closed completely; meanwhile, the
lubricating oil is poured into the guide channel. Therefore, noise and shake can be
reduced while the material is rotated in high speed.
Furthermore, the lubricating oil also can reduce the temperature resulted from
friction so the surface of material can't be damaged. The remnant material will be
pushed out off the guide channel by the push bar or the next material.
The instructions and legends of the manual are edited according to the operator
stands at the left side of the lathe.
2. DATA OF TECHNIQUE V-65E-A
2-2
2.2 Machine size
2.3 Description
V-65E-A V-65LE-A
Diameter of bar
∅
5 mm ~
∅
65 mm
Length of bar max.1250 mm
Bar length depends on
spindle length.
max. 1550 mm
Bar length depends on
spindle length.
Spindle height 850 mm ~ 1250 mm
Extend spindle height 1095 mm ~ 1500 mm
Weight 250 kg 280 kg
Air supply 5 ~ 7 kg / cm2
Power supply 220 / 380V 0.4A 50 / 60Hz
2. DATA OF TECHNIQUE V-65E-A
2-3
2.4 Compressed air supply and power supply
2.4.1 Compressed air pipe minimum Ø 8mm. Minimum pressure 6 kg/cm2. Compressed
air consumption about 50L/H.
2.4.2 Put the air supply tube into (A). Then pull and turn around the knob (B) and set the
pressure at 6kg/cm2.
2.4.3 Power supply 220V/380V，50/60Hz.
3. TRANSPORTATION V-65E-A
3-1
3. TRANSPORTATION
Hazard－
－－
－warning：
：：
：
Transportation and hoist (please refer to the item 3.2.1 of following weight table)
You have to sure the crane; forklift or other related tools could take the weight.
Using the proper equipment to move and hoist the machine should be led by the
expert personnel.
3.1 Packing the Feeder
There are three kinds of packing Feeder：
A. Unpacking.
B. On the pallet: Put the feeder on the pallet and wrap PE membrane around the
feeder.
C. Packing with wooden box: The Feeder was packed with wooden box and wrap
PE membrane around the box.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Equipos industriales de Edge Technologies
