Edge Technologies SCOUT 320 Manual de usuario
SCOUT 320
HYDRODYNAMIC AUTOMATIC BAR FEEDER
SCOUT 320/37 EXT / SCOUT 320/37R EXT
MANUAL FOR USE AND MAINTENANCE
REV. 2 DATE：2016/05/10 COD：BS0104032
S/H
INDEX SCOUT 320
I
CONTENT（
（（
（INDEX）
））
）
1 GENERAL INFORMATION
1.1 Contents of manual ----------------------------------------------------------------------
1-1
1.2 The label of manufacturer and bar feeder ------------------------------------------
1-2
1.3 Support of technique ---------------------------------------------------------------------
1-2
2 DATA OF TECHNIQUE
2.1 Instruction ----------------------------------------------------------------------------------
2-1
2.2 Machine size -------------------------------------------------------------------------------
2-2
2.3 General specification---------------------------------------------------------------------
2-2
2.4 Compressed air supply and power supply -----------------------------------------
2-3
2.5 Specification of the guide channel ----------------------------------------------------
2-4
3 TRANSPORTATION
3.1 Packing the bar feeder ------------------------------------------------------------------
3-1
3.2 Transportation and hoist ----------------------------------------------------------------
3-2
3.3 Installation area ---------------------------------------------------------------------------
3-3
4 INSTALLATION
4.1 Bar feeder - Installation -----------------------------------------------------------------
4-1
4.2 Adjustment of height ---------------------------------------------------------------------
4-1
4.3 Initial position ------------------------------------------------------------------------------
4-2
4.4 Adjustment of center ---------------------------------------------------------------------
4-2
4.5 Securing and fastening of the bar feeder -------------------------------------------
4-4
4.6 Accessory installation--------------------------------------------------------------------
4-5
4.7 Guide channel lubrication --------------------------------------------------------------
4-6
INDEX SCOUT 320
II
CONTENT（
（（
（INDEX）
））
）
5 ADJUSTMENT AND SETTING
5.1 Structure of the bar feeder --------------------------------------------------------------
5-1
5.2 Adjust loading device --------------------------------------------------------------------
5-2
5.3 Adjust and fix the anti-vibration device ----------------------------------------------
5-3
5.4 Feeding Chain -----------------------------------------------------------------------------
5-3
6
OPERATIONS AND DESCRIPTION
6.1 Par storage distinction and preparation ---------------------------------------------
6-1
6.2 Operation description --------------------------------------------------------------------
6-2
6.3 Description of settings and parameter -----------------------------------------------
6-7
7 MAINTENANCE
7.1 General maintenance -------------------------------------------------------------------
7-1
7.2 Regular maintenance --------------------------------------------------------------------
7-2
8 CAUSE OF BREAKDOWN AND TROUBLESHOOTING
8.1 Frequent cause of breakdown ---------------------------------------------------------
8-1
8.2 Breakdown on frame device -----------------------------------------------------------
8-1
8.3 Breakdown on the collect ---------------------------------------------------------------
8-1
8.4 Breakdown on feeding material -------------------------------------------------------
8-1
8.5 Refer alarm message --------------------------------------------------------------------
8-2
1. GENERAL INFORMATION SCOUT 320
1-1
1. GENERAL INFORMATION
Please read the Manual carefully before operating bar feeder.
1.1 Contents of manual
The feeder manufacturer provides this manual, which is an essential part of the
integrated products. Please act according to the indication of the manual in order
to assure operators’ safety as well as the machines’, and greatly achieve
economic efficiency and to get the best output of the machine’s capability. The
important part is printed in boldface, and included the following marks:
Warning：
：：
：
Hazard! It is possible to hurt you seriously, please be careful.
Watch out-Precautions：
：：
：
For preventing the accident or the loss of property, you should take precautions.
Important information：
：：
：
Special important know-how information
Please take use of the table of contents, you will quickly find the information you
need.
The mark shown in the manual means that the machine should be operated by a
qualified and expert operator. As to the other operation shall be handled by a
qualified personnel or professional operator of bar feeder.
1. GENERAL INFORMATION SCOUT 320
1-2
1.2 The label of manufacturer and bar feeder
A. Name of manufacturer
B. Model(Type)
C. Serial Number
D. Manufacture Date
E. Weight of Machine
F. Pneumatic Pressure
G. Rated Voltage
H. Control voltage
I. Full Load Current
J. Power
K. Short Circuit Rating
L. Wiring Drawing Number
INFORMATION：
：：
：
When inquiring or ordering the parts, please notify the manufacturer the
above–mentioned in each standards.
1.3 Support of technique
If you need any support of technique, you can inquire the service center in the
appendix at anytime.
INFORMATION：
：：
：
When you need the support of technique, please refer to the label on the bar
feeder. Tell us the data of the bar feeder.
2. DATA OF TECHNIQUE SCOUT 320
2-1
2. DATA OF TECHNIQUE
2.1 Instruction
The hydrodynamic automatic bar feeder is designed for full automatic lathe to auto
feed material, the bar feeder is suitable for digital control sliding headstock lathe
and fixed headstock lathe.
The program of the PLC system can control the bar feeder running with the lathe.
The remote control box is easily to be operated.
The bar feeder can feed circular material, cannular material and any other forms of
material. While the lathe is running, the guide channel is closed completely, at the
same time; lubricating oil into the guide channel so that the noise and vibration can
be reduced while the material is rotating in high speed.
Furthermore, lubricating oil also can reduce the temperature resulted from friction
so that the surface of the material can't be damaged.
The remnant material will be pushed out of the guide channel by the push bar or
the next material.
The descriptions and legends of the manual are according to the operator stands at
the left side of the lathe to be edited.
2. DATA OF TECHNIQUE SCOUT 320
2-2
2.2 Machine size
MOD 37
L 4599
A (Max.Bar Length) 3800
B 2150
C 584
Weight 420 kg
2.3 General Specification
Bar Diameter 3mm ( 1/8" ) ～26 mm ( 1" )
4 mm ( 3/16" ) ～21 mm ( 13/16" )
Channel Size 08 / 11 / 14 / 16 / 18 / 20 / 22 / 24 / 28
Bar Loading Capacity 220mm Ø10 x 22mm round bar
Lubricant Specification 40 (L) ISO CKB 100
Power Supply 220 / 380V 0.4A 50 / 60Hz
Pneumatic Supply 5 - 7 kg/cm²
2. DATA OF TECHNIQUE SCOUT 320
2-3
2.4 Compressed air supply and power supply
2.4.1
Tube for compressed air supply unit must be bigger than 8mm. Pressure must be
over 5~7kg / cm
2
，Consumption about 50L/H。
2.4.2
Put the air supply tube into（A）. Then pull and turn around the knob（B）and set
the pressure at 6kg / cm
2
.
2.4.3
Control air lubrication from cylinder , adjust（C）, 1-2 drops／1000 L air if
necessary.
2.4.4
Lubricate（D）, viscosity 32 Cat , temperature 40℃, ISO VG type
Adaptive lubricant
BP ENERGOL HLP32
AGIP OSO 32 MOBIL DTE 24 ESSO NUTO H32
2. DATA OF TECHNIQUE SCOUT 320
2-4
2.5 Specification of the guide channel
TYPE
Diameter
of guide
channel
(mm)
Diameter
of bar
pusher
(mm)
Diameter of bar (mm)
Min. Max.
SCOUT 320
8 7 1.5 5.5 7
11 10 2 8 10
14 12 3 10 12
12.7
16 15 3 13 14
18 16 3 13 16
17
22 20 3 17 20
21
24 23 3 19 22
28 25 5 22 25
27 26
Note！
！！
！Outer diameter of the collet must be smaller 0.5 ㎜
㎜㎜
㎜than diameter of
bar pusher at leas
Tabla de contenidos
Otros manuales de Equipos industriales de Edge Technologies
