Edelbrock 65892 Manual de usuario

Catalog #65892, #65893

Page 1 of 2 Brochure #63-65892

Rev. 9/07 - DA/mc

SHORTY HEADER

For 2006-2007 Dodge Ram Pick-Up, 1500/2500 Series,

5.7L Hemi V8, Automatic Transmission, 2WD & 4WD with I.F.S.

Catalog #65892 & #65893

INSTALLATION INSTRUCTION

Please study these instructions carefully before installing your new

Shorty Header

. If you have any questions, please contact our

Technical Hotline at : 1-800-416-8628 from 7 am - 5pm, Monday-Friday, Pacific Standard Time or e-mail us at

[email protected].

SHORTY HEADER: These components are designed as a system to improve the exhaust efficiency of the Dodge 5.7L Hemi V8 engine.

This system does not require welding for installation and retains all O.E.M. emissions equipment.

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in

poor performance and engine or vehicle damage.

Suggested Tools Needed for Installation: This vehicle has some metric fasteners.

❑3/8” rachet socket set with extensions and universal swivel sockets metric & S.A.E.

❑ Set of combination wrenches

❑ Jackstands, screwdrivers, pliers, crescent wrench, etc.

❑Liquid penetrant, (GM #1052627), anti-seize compound (GM #5613695) or available equivalent

❑Thread locking compound

SPECIAL NOTICE: This Edelbrock Shorty Header has received an Executive Order number (E.O.#) from the California Air Resources

Board (C.A.R.B.) making it legal for street use in all 50 states. To assist you with emission equipment certification, we have included

a silver fan shroud decal to help testing personnel verify that this part is a legal replacement on the vehicle for which it is cataloged.

The adhesive-backed decal should be affixed next to the existing emission and engine specifications decal. Do not cover any part of

your original emission decal.

WARNING: The use of "Thermal Wrap" or any aftermarket coating process will void the warranty on your Edelbrock Shorty

Headers. Those products can cause excessive heat and moisture buildup resulting in corrosion and failure of the system.

IMPORTANT NOTE:

When cleaning any ceramic-coated Edelbrock T.E.S., use only soap and warm water. The use of caustic solvents (i.e. gunks, etc.)

will mar or damage the ceramic-coating.

INSTALLATION INSTRUCTIONS

DISASSEMBLY

1. Disconnect negative battery cable.

2. Raise and support the vehicle with two post car hoist

(recommended) or jackstands and remove both front

wheels.

3. Remove both left and right inner fender wells and set

aside.

4. Disconnect and remove O2 sensors in the front of both

left and right catalytic converter, being careful not to

damage.

5. Unbolt exhaust pipe from stock manifolds.

RIGHT SIDE ASSEMBLY:

1. Remove heat shield from manifold.

2. Remove manifold bolts.

3. Remove stock manifold and gasket.

4. Remove the black plastic heater hose retainer clip from

the valve cover stud by pulling up until it comes off and

push heater hoses out of the way.

5. Loosen the long valve cover studs (just enough to accept

the new heat shield) with a deep 5/16” socket. Slide heat

shield stamped #25-9383 under the nuts of valve cover

studs and tighten down.

Catalog #65892, #65893

Page 2 of 2 Brochure #63-65892

Rev. 9/07 - DA/mc

KIT CONTENTS

Qty.Description Qty.Description

❑1 Manifold right side (#25-9490) (#65892) ❑2 Donut gaskets; 2”

❑1 Manifold left side (#25-9480) (#65892) ❑4 Hex capscrews; 3/8” x 2”

❑1 Manifold right side (#25-9491) (#65893) ❑17 Black hardened washer; 5/16”

❑1 Manifold left side (#25-9481) (#65893) ❑17 Lock washers; 5/16”

❑1 Heat Shield left (#25-9382) ❑4 Lock washers; 3/8”

❑1 Heat Shield right (#25-9383) ❑ 4 3/8” Hex nuts

❑ 17 Hex header bolts ❑4 3/8” Flat washers

❑2 Chrysler V8 port gaskets ❑1 Heat shield sleeve

Edelbrock Corporation, 2700 California St., Torrance, CA 90503

Tech Line: 1-800-416-8628

Office: 310-781-2222

E-Mail: [email protected]

RIGHT SIDE ASSEMBLY - Continuation:

6. Place black retainer clip back on valve cover stud and

make sure the heater hoses are laying in their stock place

and out of harm’s way.

7. Place right header into position with gasket and start all

bolts, lock washers, and hardened washers. Use anti-

seize compound on all header bolts before starting. Now,

tighten evenly from the center out.

LEFT SIDE ASSEMBLY:

1. Remove heat shield from stock manifold.

2. Remove manifold bolts.

3. Remove stock manifold and gasket.

4. Install the new heat shield stamped #25-9382 in the

same manner as the right assembly (steps #4, #5, and

#6).

5. Place left header into position with gasket. With anti-

seize on bolts, start all bolts, lock washers, and hardened

washers. Tighten bolts evenly from the center out.

6. Re-install the starter.

7. Remove the bolt and separate steering shaft just above

the universal joint. Take the heat shield sleeve (supplied

in hardware kit) and slide it over the rubber below on the

steering shaft and then re-connect the shaft back

together with the universal joint and tighten.

FINAL ASSEMBLY:

1. Place donut gaskets on both left and right headers.

2. Re-attach stock exhaust pipes to both headers using

supplied hardware.

3. Re-attach O2 sensors.

4. Re-connect battery.

5. At this point, it is a good idea to look over the complete

installation to be sure nothing was missed. Check all

hydraulic, vacuum and fuel lines, and wire looms to

ensure there is adequate clearance to exhaust

components.

6. Start vehicle and bring up to normal temperature and

check for possible leaks, correct as necessary.

7. Turn engine off and let cool then re-tighten all bolts

again (do not do while hot!).Note: Periodically

check header bolts to ensure a tight seal for best

performance.

8. Re-install inner fender wells.

9. Re-install front wheels, torque to factory specifications.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Pieza de automóvil de Edelbrock

Edelbrock

Edelbrock Quiet-Flo 1790 Manual de usuario

Edelbrock

Edelbrock Performer RPM 1967 Manual de usuario

Edelbrock

Edelbrock 71850 Manual de usuario

Edelbrock

Edelbrock Square-Bore Carb 2696 Manual de usuario

Edelbrock

Edelbrock 66112 Manual de usuario

Edelbrock

Edelbrock 66152 Manual de usuario

Edelbrock

Edelbrock 5776 Manual de usuario

Edelbrock

Edelbrock 3824 Manual de usuario

Edelbrock

Edelbrock 72285 Manual de usuario

Edelbrock

Edelbrock Harley Nitrous Systems 63-0052 Manual de usuario

Edelbrock

Edelbrock 68782 Manual de usuario

Edelbrock

Edelbrock 68722 Manual de usuario

Edelbrock

Edelbrock 5588 Manual de usuario

Edelbrock

Edelbrock 66002 Manual de usuario

Edelbrock

Edelbrock Performer 70011 Manual técnico

Edelbrock

Edelbrock 1799 Manual de usuario

Edelbrock

Edelbrock 67452 Manual de usuario

Edelbrock

Edelbrock 2886 Manual de usuario

Edelbrock

Edelbrock 72950 Manual de usuario

Edelbrock

Edelbrock 6652 Manual de usuario

Edelbrock

Edelbrock 6876 Manual de usuario

Edelbrock

Edelbrock 2934 Manual de usuario

Edelbrock

Edelbrock Performer 1670 Manual de usuario

Edelbrock

Edelbrock 66162 Manual de usuario

Manuales populares de Pieza de automóvil de otras marcas

Dakota Digital

Dakota Digital 650277 Manual de usuario

bosal

bosal 037031 Manual de usuario

Vintage Air

Vintage Air 571063 Manual de usuario

GFB

GFB EX38 Manual de usuario

bosal

bosal 028091 Manual de usuario

Dodge

Dodge 8W-43 Guía de inicio rápido

ICI

ICI Magnum FBM10DGN Manual de usuario

Volant Perfomance

Volant Perfomance 19435 Manual de usuario

BENDIX

BENDIX GEN 4 GEN 5 ABS Manual de usuario

Vintage Air

Vintage Air 571065 Manual de usuario

Rugged Ridge

Rugged Ridge 11503.13 Manual de usuario

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manual de usuario

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Guía

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manual de usuario

Toshiba

Toshiba 48-1250 A Manual de usuario

aldes

aldes EHT2 Manual de usuario

Go Rhino

Go Rhino 24371T Manual de usuario

BBK

BBK 18950 Manual de usuario