Head Office : Parc d’activites Kennedy - 20, avenue Neil Armstrong – F-33700 Bordeaux-Merignac (France)
Tel
+33
(0)5
57
928
928
–
Fax
+33
(
0)5
57
928
929
–
www.ecreso.com – [email protected]
Helios 20, 50 or 100 W, User Manual – 01/2011
Page 4
5.1.1.Input settings (MONO or MPX) ........................................................................................... 42
5.1.2.Pre-emphasis ...................................................................................................................... 43
5.1.3.Input range (MONO and MPX) ........................................................................................... 44
5.2.Physical configuration of the stereo coder ............................................................................... 45
5.2.1.Settings for the Digital Stereo Coder (pre-emphasis) ......................................................... 45
5.2.2.Input range (LEFT and RIGHT Channel) ............................................................................ 46
5.2.3.MONO Function with an analog stereo coder..................................................................... 46
5.3.Physical configuration of the Analog+ stereo........................................................................... 47
5.3.1.Settings for the Analog+ Stereo Coder (pre-emphasis)...................................................... 47
5.3.2.Analog+ Stereo coder transmission mode.......................................................................... 47
5.3.3.Analog+ Stereo coder input range settings......................................................................... 48
5.4.Physical configuration of the AES Digital stereo encoder........................................................ 48
5.4.1.Settings for the AES Digital stereo encoder (pre-emphasis) .............................................. 48
5.4.2.AES Digital stereo encoder transmission mode.................................................................. 49
5.4.3.AES Digital stereo encoder input range settings ................................................................ 49
5.5.Installation ................................................................................................................................ 49
5.6.Adding an optional card............................................................................................................ 50
5.7.Connections ............................................................................................................................. 50
6. SET-UP.............................................................................................................................................. 52
6.1.Recommended test equipment ................................................................................................ 52
6.2.Set-up....................................................................................................................................... 52
6.3.Advanced operation ................................................................................................................. 54
6.3.1.Parameters configuration .................................................................................................... 54
6.3.2.System parameters ............................................................................................................. 56
6.3.3.Checking the Helios settings............................................................................................... 57
6.3.4.Checking the Goliath settings ............................................................................................. 58
6.3.5.Checking the Ines settings .................................................................................................. 59
6.3.6.RF power setting of the set ................................................................................................. 60
6.3.7.DISTANT mode display....................................................................................................... 60
6.4.Indicators and alarms ............................................................................................................... 62
7. SERIAL COMMANDS....................................................................................................................... 63
7.1.Serial commands...................................................................................................................... 63
7.2.Hyper Terminal connection ...................................................................................................... 73
8. REMOTE CONTROL AND REMOTE MONITORING SYSTEM....................................................... 76
8.1.Introduction............................................................................................................................... 76
8.2.RC and RM functions ............................................................................................................... 76
8.2.1."Remote control" functions.................................................................................................. 76
8.2.2."Remote monitoring" functions............................................................................................ 78
8.2.3.Dry-loop activation according to the transmitter status....................................................... 79
8.2.4.Schematic diagram of the inputs and outputs..................................................................... 80
8.2.5.Connectors wiring ............................................................................................................... 81
8.3.Description of RC/RM boards .................................................................................................. 82
8.3.1.Transmitter configuration .................................................................................................... 83
8.3.2.Board presentation.............................................................................................................. 84
8.4.Physical configuration of RC/RM boards ................................................................................. 86
8.4.1.Configuration of inputs/outputs ........................................................................................... 86
8.4.2.Standard configurations ...................................................................................................... 89
8.5.CAN board physical configuration............................................................................................ 90
8.6.Serial port commands .............................................................................................................. 90
8.7.Accessing the embedded web site........................................................................................... 96
8.7.1.Connecting to the embedded web site................................................................................ 96
8.7.2.Viewing the Status .............................................................................................................. 98
8.7.3.Transmitter Configuration.................................................................................................... 99
8.7.4.Maintenance pages........................................................................................................... 100
8.7.5.System Configuration........................................................................................................ 104
