Echoflex Elaho E-VAC-SR Manual de usuario

Echoflex Installation Guide

Elaho Responsive Vacancy Sensor

Ma in Office Squamish, BC, Canada Phone +1 778 733 0111

Email info@echoflexsolutions.com Web echoflexsolutions.com

Echoflex intends this document to be provided in its entirety.

Product information and specifications subject to change.

8186M2182 Rev B Released 2020-12

Overview

The Elaho Vacancy Sensor is a ceiling mounted sensor that utilizes passive

infrared (PIR) technology, providing reliable vacancy detection for lighting

control. The sensor relies on local station control for manual on and provides

auto off functionality upon detection of vacancy.

The Vacancy Sensor provides 360 degree coverage of the installed location

and is available in these models:

Model Coverage m2Coverage ft2

E-VAC-SR

SmallRoom

41.8m2at2.4m 450 ft2at 8 ft

74.3 m2at 6.7 m 800 ft2at 12 ft

E-VAC

LargeRoom

167 m2at 2.4 m 1,800 ft2at 8 ft

279 m2at 6.7 m 3,000 ft2at 12 ft

E-VAC-HC

HighCeiling

28 m2at 2.4 m 300 ft2at 10 ft

650 m2at 12.2 m 7,000 ft2at 40 ft

Field-installed lens masks are provided to allow customized occupancy

detection fields for each sensor lens type.

Custom Configuration

This document guides you through the installation and local DIP switch setup

of the sensor. For more detailed information about custom configuration

options available using ElahoAccess, see the ElahoAccess App integrated help

system.

Note:

To use the configuration settings applied using ElahoAccess,

DIP switch 2 must be enabled. See DIP Switch Settings on page8.

Echoflex Installation Guide

Vacancy Sensor

Prepare for Installation

Ceiling-mount sensors are intended for installation to a finished ceiling

surface, soft ceiling tile mounted, or attached to a round or octagonal fixture

junction box.

Compliance

•

cULus Listed

•

CE compliant

For use with Echoflex Elaho Control Systems, powered by an Elaho station

power supply.

Environment

Ambient

For indoor, commercial controls use only. Operating temperature 0-40°C

(32-104°F), humidity maximum 90%(non-condensing).

Location

Echoflex recommends paying special attention to the installation

environment:

•

The sensor must have an unobstructed view of the room. Do not

mount behind or near tall cabinets, shelves, hanging light fixtures, etc.

•

Do not install the sensor within eight feet from an HVAC airflow

duct/vent.

•

Install the sensor where it cannot easily sense movement in areas

outside of the intended space, such as hallways, glass partitions, or

adjacent rooms. If the installation location cannot avoid these

conditions, portions of the lens can be masked to block the sensor

view of these undesired areas. See

Lens Masking on page11

Wire Specification

The Vacancy Sensor connects to the EchoConnect communication bus.

EchoConnect is a bi-directional protocol that uses one pair of wires (data+

and data-) for both data and power. Echoflex recommends using Belden

8471 Class 2 wire (or approved equal - see the Echoflex cable cross database

echoflexsolutions.com/files/Elaho_Data_Cable_Wire_Specs for equal

alternatives). The total combined length of an EchoConnect wire run using

Belden 8471 may not exceed 500m (1,640ft), with a maximum distance of

400m(1,312ft) between any two devices.

Vacancy Sensor Page 2 of 12 Echoflex

Echoflex Installation Guide

Vacancy Sensor

Note:

All control wiring should be installed and terminated by a

qualified installer and should follow standard wiring installation

practices. Leave approximately 25.4cm (10in) of wiring in the back

box for connection and to allow slack for future service needs.

Note:

Echoflex requires that all stations and devices be grounded for

ESDprotection. Pull an additional 2.5 mm2(14AWG) wire for

grounding when control wires are not installed in grounded metal

conduit.

Note:

When using Category 5 (or equivalent) cable on the

EchoConnect communication bus, please note the following:

•

Cat5 wiring must be terminated using EchoConnect Cat5

Termination Kit and must be installed using a bus topology.

Refer to the installation guide that is provided with the Cat5

Termination Kit (8186A1207) for information to terminate

Cat5 wiring.

•

Not all topologies are supported using Cat5; careful planning

is required to ensure the proper termination kits are available

and the wire is pulled appropriately.

Supplies

The following supplies are provided with the sensor:

•

EchoConnect and ESD ground wire pigtails

•

Soft ceiling tile adapter

•

Mounting screws, 8-32 x 1 3/4”

•

Lens masks

Installation

Note:

Installation must follow all national and local codes for

electrical equipment. NEC Class 2 product to be wired in accordance

to NEC Article 725 and local jurisdiction requirements.

The ceiling-mount sensor is provided with a mounting plate that can be

mounted to a junction box, finished ceiling, or soft ceiling tile. Determine the

installation method and follow the detailed instructions:

•

Junction Box or Surface Installation on the next page

•

Soft Ceiling Tile Installation on page5

Vacancy Sensor Page 3 of 12 Echoflex

Echoflex Installation Guide

Vacancy Sensor

Junction Box or Surface Installation

Terminate

wires here

1. Pull the Belden 8471 (or

equivalent) and one 2.5mm2

(14AWG) ground wire to the

mounting location (junction

box or finished surface).

2. If you are installing the

sensor in series with other

sensors or stations

(continuing the data run),

use the provided

EchoConnect and

ESDground wire pigtails.

Termination connectors are

not provided. If you are not continuing the data run, direct

termination to the sensor controller is recommended, skip this step

and proceed to step3.

a. Strip each wire to the appropriate length, depending on the wire

nut or other termination used (wire nuts are not provided).

b. Twist the incoming data-EchoConnect wire(typically black) and

the data-wire(black) from the EchoConnect pigtail as well as any

continuing data-EchoConnect wire together and secure with a

wire nut.

c. Repeat the above step for the data+EchoConnect wire(typically

white) and for the ESD ground wire (typically green/yellow), using

a new wire nut for each termination type.

3. Orient the flat side of the mounting plate to the junction box and pull

the EchoConnect wires or terminated pigtail from the junction box

through the provided holes near the center of the mounting plate.

4. Secure the mounting plate to the junction box using the screws

provided.

5. Terminate EchoConnect and ESD ground wires to the terminal block

on the sensor controller. Torque each terminal 3.1-3.5in-lb.

a. Strip each wire 8mm (5/16in).

b. Insert the data+ (typically white)EchoConnect wire into the

data+ terminal and secure.

c. Insert the data- (typically black) EchoConnect wire to the data-

terminal and secure.

d. Insert the green/yellow (ground) wire into the ground terminal

and secure.

Vacancy Sensor Page 4 of 12 Echoflex

Echoflex Installation Guide

Vacancy Sensor

6. Attach the sensor to the mounting plate by aligning the tabs on the

sensor with the slots on the mounting plate, and then twist clockwise

until the two are secured in place.

Soft Ceiling Tile Installation

EchoConnect and

Ground wire pigtails

optional

Ceiling tile

adapter

Terminate

wires here

Ceiling tile

1. Pull the Belden 8471 (or equivalent) and 2.5mm2(14AWG) ) ground

wire to the mounting location and strip each wire to the appropriate

length. The strip length is dependent on the wire nut or other

termination connector used (wire nuts are not provided).

2. If you are installing the sensor in series with other sensors or

stations (continuing the data run), use the provided EchoConnect and

ESDground wire pigtails. Termination connectors are not provided. If

you are not continuing the data run, direct termination to the

sensor controller is recommended, skip this step and proceed to

step3.

a. Strip each wire to the appropriate length, depending on the wire

nut or other termination used (wire nuts are not provided).

b. Twist the incoming data-EchoConnect wire(typically black) and

the data-wire(black) from the EchoConnect pigtail as well as any

continuing data-EchoConnect wire together and secure with a

wire nut.

c. Repeat the above step for the data+EchoConnect wire(typically

white) and for the ESD ground wire (typically green/yellow), using

a new wire nut for each termination type.

Vacancy Sensor Page 5 of 12 Echoflex

Echoflex Installation Guide

Vacancy Sensor

3. Prepare the ceiling tile.

a. Align the flat side of the sensor mounting plate to the finished

side of the ceiling tile and mark the center access hole for wire

pass-through.

b. Remove the ceiling tile material from marked access hole.

c. Pull the sensor wires through the access holes to the unfinished

side of the ceiling tile.

4. Secure the sensor mounting plate in place.

a. Insert the soft ceiling tile adapter through the pinholes on the

mounting plate.

b. Push the adapter through the ceiling tile, and then bend each

tine over in opposite directions for a secure fit on the unfinished

side of the ceiling tile.

5. Terminate EchoConnect and ESD ground wires to the terminal block

on the sensor controller. Torque each terminal 3.1-3.5in-lb.

a. Strip each wire 8mm (5/16in).

b. Insert the data+ EchoConnect wire (typically white)into the

data+ terminal and secure.

c. Insert the data- EchoConnect wire (typically black) to the data-

terminal and secure.

d. Insert the ESD ground wire (typically green/yellow) into the

ground terminal and secure.

6. Attach the sensor to the mounting plate by aligning the tabs on the

sensor with the slots on the mounting plate, and then twist clockwise

until the two are secured in place.

Vacancy Sensor Page 6 of 12 Echoflex

Echoflex Installation Guide

Vacancy Sensor

Settings

The Elaho Responsive

Vacancy Sensor participates

in an Elaho control system

using the configured Space

and Address, which are

selectable using the rotary

switches on the sensor

electronics.

DIPswitches, also located on

the sensor electronics, set

the sensor functionality.

Note:

When the sensor is placed into Custom configuration mode,

DIP switch 2 set to On, all other DIP switch settings are ignored.

Note:

The [MODE] and Auxiliary [A] buttons, and their related LEDs,

are not used and have no functionality on the Responsive Vacancy

Sensor.

Set Space and Address

Two rotary switches on the sensor electronics provide for Space and Address

assignment for the sensor. By default, these switches are set to Space1,

Address1. Commands are shared by all devices within a given space.

1. Set the Space rotary switch to the desired number (1 through 16) for

the space you want the sensor to control.

2. Set the Address rotary switch to desired address (1 through 16) for the

sensor identification in the selected space.

Note:

Do not duplicate a device Address within the same Space.

Vacancy Sensor Page 7 of 12 Echoflex

Echoflex Installation Guide

Vacancy Sensor

DIP Switch Settings

DIP switches on the sensor electronics provide for additional configuration

options including Use Custom Config, Vacancy Timeout, Enable/Disable PIR

detection LED, and the ability to restore the sensor to its factory defaults.

Switch # Use

1Unused (leave Off)

2Enable/Disable Custom Config Mode

•

When “Custom Config” is set to Off (also known as Basic

configuration mode), local DIP switch settings for Vacancy

Timeout and Enable PIR LED are used. See

Configuration

on page 9

•

When “Custom Config” is set to On, all other local DIP

switch settings are ignored. Instead, the settings made by

the ElahoAccess App are used.

3 and 4 Vacancy Timeout

•

5 min = Switches 3 and 4 are Off

•

15 min = Switch 3 is Off and Switch 4 is On (default)

•

30 min = Switch 3 is On and Switch 4 is Off

•

Auto = Both switches are On (See

Vacancy Timeout on

page10

5PIRDetection LED

•

When set to On (default), the occupancy detection LED

illuminates the lens when movement is detected.

•

When set to Off, the occupancy detection LED is disabled

unless the unit is in Walk Test mode.

6Unused (leave Off)

7Unused (leave Off)

8Restore to Defaults at boot

•

When set to On and power is cycled to the sensor, the

unit restores to its factory default settings.

•

Off is the default setting.

Vacancy Sensor Page 8 of 12 Echoflex

Echoflex Installation Guide

Vacancy Sensor

Power Up

All EchoConnect terminations in the system must be made before applying

power to the system and sensor. When the sensor is powered up, the PIR LED

illuminates for one minute for calibration and warm-up. The PIR detection

features of the sensor will automatically adjust the sensitivity threshold to

eliminate nuisance tripping. During this time configuration is not allowed

and no events are triggered.

Configuration

Basic

When the sensor is in Basic configuration mode (DIP switch 2 set to Off), the

sensor will activate a Space Off command when vacancy is detected.

Custom

When functionality other than Space Off is required, place the sensor in

Custom configuration mode (DIP switch 2 set to On). Customization of the

sensor and all actions are configured using the ElahoAccess App.

For more detailed information about custom configuration options available

using ElahoAccess, see the ElahoAccess App integrated help system.

Vacancy Sensor Page 9 of 12 Echoflex

Echoflex Installation Guide

Vacancy Sensor

Operation

•

When the space is vacant, manual control can switch the state to

occupied.

•

When the space is occupied, PIRdetection and manual control can

reset the vacancy timeout.

Vacancy Timeout

Vacancy timeout is the amount of time the sensor waits to take action after

no movement is detected. By default, vacancy timeout is set to 15 minutes

(indicated by DIP switch 3 set to Off and 4 set to On; see

DIP Switch Settings

on page8

). When the vacancy timeout ends, the grace period begins.

When the sensor detects vacancy, the vacancy timeout period begins. If the

sensor does not detect occupancy again during the vacancy timeout period,

the lights turn off and a 30 second grace period begins.

Grace Period

The sensor features a 30 second grace period after a vacancy timeout occurs.

During this grace period, if the sensor detects occupancy, it will turn on or

restore the previous lighting condition.

Auto Vacancy Timeout

The “Auto” vacancy timeout setting varies the vacancy timeout between

5 and 30 minutes depending on how often it identifies an occupancy trigger

after a vacancy timeout occurs (during the grace period).

Vacancy Sensor Page 10 of 12 Echoflex

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de echoflex

echoflex

echoflex MOS-17 Manual de usuario

echoflex

echoflex MOS-21 Series Manual de usuario

echoflex

echoflex MC-31 Manual de usuario

echoflex

echoflex Elaho Manual de usuario

echoflex

echoflex Elaho Dual Tech Wall-mount Vacancy Sensor Manual de usuario

echoflex

echoflex TAP-21C Manual de usuario

echoflex

echoflex TAP-21 Series Manual de usuario

echoflex

echoflex ERUSB-C Manual de usuario

echoflex

echoflex TAP-17 Manual de usuario

echoflex

echoflex TAP-31 Manual de usuario

echoflex

echoflex Elaho Manual de usuario

echoflex

echoflex FLS-41 Manual de usuario

echoflex

echoflex RVS-A-XW Manual de usuario

echoflex

echoflex OWS Manual de usuario

echoflex

echoflex Elaho Dual Tech Ceiling-mount Vacancy Sensor Manual de usuario

echoflex

echoflex RVS-A-xW Manual de usuario

echoflex

echoflex RVS-A-xW Series Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

echoflex Elaho E-VAC-SR Manual de usuario

Manuales populares de Accesorios de otras marcas