Echoflex Elaho Dual Tech Wall-mount Vacancy Sensor Manual de usuario

Echoflex Installation Guide

Elaho Dual Tech Wall-mount Vacancy Sensor

Main Office nSquamish, BC, Canada nToll Free +888 324 6359 nPhone +778 733 0111 nFax +604 815 0078

Email info@echoflexsolutions.com nWeb echoflexsolutions.com nProduct information and specifications subject to change.

8186M2186 nRevision A nReleased 2018-09

Overview

The Elaho Dual Tech Wall-mount Vacancy Sensor uses passive infrared (PIR)

technology and acoustic detection to provide reliable vacancy sensing for

lighting control. The sensor relies on local station control for manual on and

provides auto off functionality upon detection of vacancy.

The wall-mount unit offers up to 140 degree field of

detection with optimized lens options to accommodate

wide or narrow angle spaces and is available in white,

black or cream finish.

Wall-mount - Wide Angle Lens - coverage

•

60 ft (18.3 m) mounting height at 7–10 ft (2.1–3 m)

•

140 degree field of detection

Wall-mount - Narrow Angle Lens - coverage

•

16 ft (4.9 m) by 75 ft (22.9 m) coverage at mounting

height of 6–7 ft (1.8–2.1 m)

•

40 degree field of detection

See

Sensor Coverage on page 11

Custom Configuration

This document guides you through the installation and local DIP switch setup

of the sensor.

For more detailed information about custom configuration options available

using ElahoAccess, see the ElahoAccess Mobile App integrated help system.

Note: To use the configuration settings applied using ElahoAccess, DIP

switch 2 must be enabled. See DIP Switch Settings on page7.

Echoflex Installation Guide

Dual Tech Vacancy Sensor

Prepare for Installation

Elaho Dual Tech Wall-mount Vacancy Sensors ship with electronics, a

decorator style wall plate, and a termination kit. The sensor may be installed

into an industry standard back box (provided by others) or surface mounted

back box (sold separately and available from Echoflex).

Note: Installation must follow all national and local codes for electrical

equipment.

Compliance

•

UL/cUL listed, complies with UL508A, UL916, and CSAC22.2 No.14

•

CE compliant

For use with Echoflex dimming and relay products.

Environment

Ambient

For indoor, commercial controls use only. The sensor operates in ambient

temperatures of -10°C to 40°C, with a maximum of 90% non-condensing

humidity.

Installation

Echoflex recommends paying special attention to the installation

environment:

•

When operating in PIR only modes, the sensor must have an

unobstructed view of the room. Do not mount behind or near tall

cabinets, shelves, hanging light fixtures, etc.

•

Do not install the sensor within eight feet from an HVAC airflow

duct/vent.

•

Install the sensor where it cannot easily sense movement in areas

outside of the intended space, such as hallways, glass partitions, or

adjacent rooms.

Note: In areas of increased noise activity, enabling PIR only mode may

allow for better occupancy detection results. See DIP Switch Settings on

page 7.

Dual Tech Wall-mount Vacancy Sensor Page 2 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Vacancy Sensor

Control Wire Specification

The sensor connects to the EchoConnect®communication bus. EchoConnect is

a bidirectional protocol that uses one pair of wires (data+ and data-) for both

data and power. Echoflex recommends using Belden 8471 (or approved equal)

Class 2 wire. The total combined length of an EchoConnect wire run (using

Belden 8471, or equal) may not exceed 1,640feet (500m).

Note: All control wiring should be installed and terminated by a

qualified installer and should follow standard wiring installation practices.

Leave approximately 8" (20cm) of wiring in the back box for connection

and to allow slack for future service needs.

Note: Echoflex requires that all Elaho stations and devices be grounded

for ESDprotection. Pull an additional 14AWG (2.5 mm2) wire for

grounding when control wires are not installed in grounded metal conduit.

Note: When using Category 5 (or equivalent) cable on the EchoConnect

communication bus, please note the following:

•

Cat5 wiring must be terminated using EchoConnect Cat5

Termination Kit and must be installed using a bus topology.

Refer to the installation guide that is provided with the Cat5

Termination Kit (8186A1207) for information to terminate

Cat5 wiring.

•

Not all topologies are supported using Cat5; careful planning

is required to ensure the proper termination kits are available

and the wire is pulled appropriately.

Parts and Supplies

The following parts and supplies are included with the sensor:

•

mounting bracket with pre-routed EchoConnect and ground wires

•

mounting screws

•

WAGO connectors (wire termination connectors)

•

decorator style wall plate

Dual Tech Wall-mount Vacancy Sensor Page 3 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Vacancy Sensor

Installation

Note: Follow all local code requirements for terminating wire.

The wall-mount sensor is provided with a mounting bracket with pre-routed

wires that can be mounted to a back box. Follow the detailed instructions for

installation.

1. Pull the Belden 8471 (or equivalent) and one 14 AWG (2.5 mm

) ground

wire to the mounting location (switch box or surface) and strip each

wire 3/8” (9–10 mm).

2. Connect the EchoConnect pigtail wires from the mounting bracket to

the installed wall wires.

a. Connect the data - (typically black) EchoConnect wire from

mounting bracket to the incoming EchoConnect (typically black)

wire using a WAGO wire termination connector.

b. Repeat the above steps for the data + (typically white)

EchoConnect wire and for the ESD ground wire, using a new

WAGO connector for each termination type.

3. Orient the mounting plate, with the directional arrows in the upright

position, to the mounting box and secure it in place using the two

screws provided.

Dual Tech Wall-mount Vacancy Sensor Page 4 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Vacancy Sensor

4. Install the wall plate to the

mounting plate.

a. Align the top of the wall

plate to the mounting

plate, angling the bottom

slightly.

b. Hook the top of the wall

plate to the tabs located

on the mounting plate.

c. Swing the wall plate

down, ensuring the neck

of the sensor extension

and wires feed through

the opening, until the

magnets engage.

d. If the wall plate does not fully attach, wiggle the bottom of the

plate until all of the magnets are seated properly.

5. Attach the sensor

head.

a. Slide the

removable

cover off

the sensor

head.

b. Route the

three

position

connector

with wiring

pigtail

through the

sensor

head.

c. Loosen the set screw on the sensor retaining ring.

d. Slide the sensor onto the ball socket, then tighten the set screw

until secure.

6. Connect the three position connector to the receptacle on the sensor

electronics.

Dual Tech Wall-mount Vacancy Sensor Page 5 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Vacancy Sensor

Sensor Configuration

MODE AUX

The Elaho Dual Tech Wall-mount Vacancy

Sensor participates in an Elaho control

system using the configured Space and

Address, which are selectable using the

rotary switches on the sensor electronics

located behind the removable cover.

DIPswitches, also located on the sensor

electronics, set the sensor functionality.

Note: The [MODE] and [AUX] buttons, and their related LEDs, are not

used and have no functionality on the Dual Tech Wall-mount Vacancy

Sensor.

Set Space and Address

Two rotary switches on the controller provide for assignment of the sensor

Space and Address. By default, these switches are set to Space 1, Address 1.

Commands are shared by all devices within a given space.

1. Set the Space rotary switch to the desired number (1 through 16) for

the space you want the sensor to control.

2. Set the Address rotary switch to desired address (1 through 16) for the

sensor identification in the selected space.

Note: Do not duplicate a device Address within the same Space.

Dual Tech Wall-mount Vacancy Sensor Page 6 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Vacancy Sensor

DIP Switch Settings

DIP switches on the sensor electronics provide for additional configuration

options including Use Custom Config, Vacancy Timeout, Enable/Disable

detection LEDs, PIR Only, and the ability to restore the sensor to its factory

defaults.

Switch # Use

1Unused

Enable/Disable Custom Config Mode

•

When “Custom Config” is set to Off (also known as Basic

configuration mode), local DIP switch settings for Vacancy

Timeout, Enable PIR LED, and dual technology features are

used. See

Configuration using Elaho Program Mode on

page1

•

When “Custom Config” is set to On, all other local DIP

switch settings are ignored. Instead, the settings made by

the EchoAccess Mobile App are used.

3 and 4

Vacancy Timeout

•

5 min = Switches 3 and 4 are Off

•

15 min = Switch 3 is Off and Switch 4 is On (default)

•

30 min = Switch 3 is On and Switch 4 is Off

•

Auto = Both switches are On

Detection LEDs

•

When set to On (default), the occupancy detection LEDs

illuminate when movement is detected.

•

When set to Off, the occupancy detection LEDs are

disabled unless the unit is in Walk Test mode.

PIR Only Mode

•

When set to On, acoustic detection technology is disabled

for the sensor.

•

When set to Off (default), both PIR and acoustic detection

technologies are used by the sensor.

7Unused

Restore to Defaults at boot

•

When set to On, then cycling power to the sensor, the unit

restores to its factory default settings.

•

Off is the default setting.

Dual Tech Wall-mount Vacancy Sensor Page 7 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Vacancy Sensor

Power Up and Test

Power Up

All EchoConnect terminations in the system must be made before applying

power to the system and sensor. When the sensor is powered up, the PIR and

acoustic detection LEDs illuminate for one minute for calibration and warm-

up, then return to normal operation according to the configuration.

Both the PIR and acoustic detection features of the sensor will automatically

adjust sensitivity threshold to eliminate nuisance tripping. During this time,

sensor configuration is not allowed and no events are triggered.

Dual Technology

When both PIR and acoustic detection are used, the following logic is used:

•

When the space is vacant, only manual control can switch the state to

occupied.

•

When the space is occupied, PIR, acoustic detection, and manual

control can reset the vacancy timeout.

•

When the vacancy timeout in the space has only been reset by acoustic

detection for 60 minutes, acoustic detection is disabled until the next

PIR detection event.

PIR (only) Detection

When acoustic detection is disabled (DIP switch 6 set to On), the following

logic is used:

•

When the space is vacant, only manual control can switch the state to

occupied.

•

When the space is occupied, PIR detection and manual control can

reset the vacancy timeout.

Basic Configuration

When the sensor is in Basic configuration mode (DIP switch 2 set to Off), the

sensor will activate a Space Off command when vacancy is detected.

Custom Configuration Mode

When functionality other than Space Off is required, place the sensor in

Custom configuration mode (DIP switch 2 set to On). Customization of the

sensor and all actions are configured using the ElahoAccess Mobile App.

For more detailed information about custom configuration options available

using ElahoAccess, see the ElahoAccess Mobile App integrated help system.

Dual Tech Wall-mount Vacancy Sensor Page 8 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Vacancy Sensor

Vacancy Timeout

Vacancy timeout is the amount of time the sensor waits to take action after

no movement is detected. By default, vacancy timeout is set to 15 minutes

(indicated by DIP switch 3 set to Off and 4 set to On; see

DIP Switch Settings

on page 7

). When the vacancy timeout ends, the grace period begins.

When the sensor detects vacancy, the vacancy timeout period begins. If the

sensor does not detect occupancy again during the vacancy timeout period,

the lights turn off and a 30 second grace period begins.

Grace Period

The sensor features a 30 second grace period after a vacancy timeout occurs.

During this grace period, if the sensor detects occupancy, it will turn on or

restore the previous lighting condition.

Auto Vacancy Timeout

The “Auto” vacancy timeout setting varies the vacancy timeout between

5 and 30 minutes depending on how often it identifies an occupancy trigger

after a vacancy timeout occurs (during the grace period).

Dual Tech Wall-mount Vacancy Sensor Page 9 of 12 Echoflex Solutions, Inc.

Echoflex Installation Guide

Dual Tech Vacancy Sensor

Walk Test

The sensor offers a Walk Test mode, which shortens the vacancy timer to ten

seconds and allows for simple and quick verification of the sensor’s coverage

and range in the installed space.

[Walk Test]

button

1. Prepare the site for configuration.

a. Make certain the sensor and lighting loads are powered and

connected for control by the Elaho control system.

b. You will need direct access to the sensor in order to place it into

Walk Test mode.

2. Press the [Walk Test] button on the bottom of the sensor to enable

the Walk Test feature. A green LED will flash, indicating Walk Test is

enabled and the vacancy timer will be shortened to ten seconds.

3. Move throughout the space including corners and areas that may be

obscured from line of sight to the sensor. Each time the sensor detects

movement, the lens illuminates red. If acoustic detection is enabled,

any sound detected will illuminate the lens green.

4. As needed, adjust the angle of the sensor head to obtain optimal

detection in the space.

5. Walk Test mode automatically exits and the sensor returns to normal

operation after five minutes. You can also manually terminate by

pressing the [Walk Test] button again.

Dual Tech Wall-mount Vacancy Sensor Page 10 of 12 Echoflex Solutions, Inc.

Tabla de contenidos

Otros manuales de Accesorios de echoflex

echoflex

echoflex ERUSB-C Manual de usuario

echoflex

echoflex Elaho Manual de usuario

echoflex

echoflex RVS-A-xW Manual de usuario

echoflex

echoflex Elaho E-VAC-SR Manual de usuario

echoflex

echoflex FLS-41 Manual de usuario

echoflex

echoflex TAP-21 Series Manual de usuario

echoflex

echoflex MC-31 Manual de usuario

echoflex

echoflex Elaho Dual Tech Ceiling-mount Vacancy Sensor Manual de usuario

echoflex

echoflex Elaho Manual de usuario

echoflex

echoflex MOS-21 Series Manual de usuario

echoflex

echoflex TAP-21C Manual de usuario

echoflex

echoflex TAP-31 Manual de usuario

echoflex

echoflex MOS-17 Manual de usuario

echoflex

echoflex OWS Manual de usuario

echoflex

echoflex RVS-A-XW Manual de usuario

echoflex

echoflex RVS-A-xW Series Manual de usuario

echoflex

echoflex TAP-17 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

echoflex Elaho Dual Tech Wall-mount Vacancy Sensor Manual de usuario

Manuales populares de Accesorios de otras marcas