Eaton S611 Manual

Installation Leaet IL03901007E Effective June 2011

S611 User Interface Remote Mounting

Installation Leaﬂet

Disconnect power in accordance with federal, state, and local codes and remove the S611 from the enclo-

sure or mounting panel.

NOTE: Servicing the S611 while installed in an enclosure or mounted vertically on a panel is not recom-

mended.

Place the unit on a clean work surface.

Cover Removal

1. Disconnect all control wiring and tie wraps securing any wiring to the cover assembly.

2. Remove cover screws with nuts. 6 each on Frames A – D, 4 each on Frames E - F.

NOTE: Cover screw nuts are prevented from rotating but are not retained in place by the pole

supports. Do not allow hardware to fall into the soft starter.

3. Lift top of cover approximately 6” to gain access to the BYPASS VOLTAGE contactor

connector mounted on the Printed Circuit Board (PCB). See Figure 1.

4. Press locking tab on BYPASS VOLTAGE contactor connector and disconnect from the PCB.

5. Carefully rotate cover to rest onto work surface as shown. See Figure 2.

Figure 1 - Contactor Connector Figure 2 - Cover Position

Mounting The Remote Display

If necessary, remove the User Interface from the cover using a 30mm pilot device tool (E22CW recom-

mended).

1. Drill or punch two 30mm pilot holes on 1.75-inch centers a minimum of 1.60 inches (40.6 mm)

from every door gasket (see Figure 3).

2. Insert remote display through the door and add two gaskets provided behind the door

(see Figure 4).

Installation Leaet IL03901007E

Effective June 2011

S611 Soft Starters

Eaton Corporation

Electrical Sector

1111 Superior Ave.

Cleveland, OH 44114

United States

877-ETN-CARE (877-386-2273)

Eaton.com

Publication No. IL03901007E

June 2011 Rev.001

PowerChain Management is a registered

trademark of Eaton Corporation.

All other trademarks are property of their

respective owners.

Figure 3 - Pilot Device Holes - Inch[mm]

Minimum to all

gaskets ordoor

mounteddevices

1.60

[40.6]

1.75

[44.5]

Gaskets

E22CW

Tighten

Figure 4 - Door Cut Away For Clarity

3. Orient strain relief bracket with respect to your chosen cable routing.

4. Add two jam nuts provided and tighten 30mm pilot device tool until the strain relief bracket is

flush with the enclosure door, tighten an additional ½ of a turn.

Connecting the Remote Display

1. Route cable from User Interface to PCB (see Figures 5 & 6).

2. Secure cable to the strain relief bracket using any suitable tie wrap.

3. Reinstall cover assembly.

Figure 5 - Interconnecting Cable - PCB Figure 6 - Interconnecting Cable - User Interface

Cover Reinstallation

1. As the cover is placed onto the supports, carefully guide wiring into place.

2. Ensure that the BYPASS VOLTAGE contactor connector is properly connected prior to installing

the cover screws.

3. Install and torque all cover assembly screws to 22 – 27 lb-in.

4. Reinstall control wiring.

Otros manuales para S611

Tabla de contenidos

Otros manuales de Controladores de Eaton

Eaton

Eaton MVX9000 Series Manual de usuario

Eaton

Eaton JOCKEY Touch Hoja de especificaciones

Eaton

Eaton Cutler-Hammer ELC Series Guía de instalación

Eaton

Eaton CGLine+ Instrucciones de funcionamiento y mantenimiento

Eaton

Eaton xComfort CSEZ-01/16 Manual de usuario

Eaton

Eaton xComfort CRCA-00/10 Manual de instrucciones

Eaton

Eaton WaveLinx series Manual de usuario

Eaton

Eaton EMS-SWD Series Manual de usuario

Eaton

Eaton ESWA4500C Manual de usuario

Eaton

Eaton XV-102 Series Manual de usuario

Eaton

Eaton AMPGARD Manual

Eaton

Eaton SVX9000 Series Manual de usuario

Eaton

Eaton MMX11 Series Manual de usuario

Eaton

Eaton Vikers V200 Series Manual de usuario

Eaton

Eaton CGLine+ Web-Controller Manual de usuario

Eaton

Eaton Ampgard 720A Manual de programación

Eaton

Eaton Crouse-hinds series Manual de usuario

Eaton

Eaton SONIX 2Mx Manual de usuario

Eaton

Eaton LMR PLUS Manual de usuario

Eaton

Eaton PowerXL DE1 series Manual de usuario

Eaton

Eaton LS Series Manual

Eaton

Eaton Cutler-Hammer Pow-R-Command JCI-100 Manual

Eaton

Eaton RF System 2.42 Manual de usuario

Eaton

Eaton xComfort CHVZ-01/04 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario