E-RM 2G-StarLink TrackerSF Manual de usuario
ERM Electronic Systems LTD
16 Hasar Shapira St. Rishon LeZion, 75704 Israel | Phone: 972-3-9413313 Fax: 972-3-9413330
2G / 4G –StarLink TrackerSF
Installation Manual
Release 1.1
© Copyright 2017 by ERM Electronic Systems Ltd.
Revision updates log:
Revision
Change
Date
1.0
First version
07/05/2017
1.1
Version Update
25/02/2018
1.2
Version Update
2019/519/0
StarLink TrackerSF Installation Manual
ERM Advanced Telematics page: 2
Table of Contents
1. THE STARLINK 2G /4G V2 3
2. SAFETY INSTRUCTIONS 3
3. GENERAL INSTRUCTIONS 4
4. TOOLS AND EQUIPMENT/MATERIALS REQUIRED 6
5. INSTALLING STARLINK DEVICES 7
5.1 Know the StarLink Family of Tracking Devices 8
5.2 Positioning StarLink Devices in the vehicle 11
5.2.1 General Installation Instructions 11
5.2.2 StarLink Location for Optimal Reception Quality 11
6. STARLINK CONFIGURATION 13
6.1 USB Adapter 13
6.2 USB Driver 16
7. ERM CONTACT INFORMATION 16
StarLink TrackerSF Installation Manual
ERM Advanced Telematics page: 3
1. The StarLink 2G / 4G
This guide provides information about the StarLink 2G / 4G with internal eSafe and CAN,
and describes its recommended installation procedures.
2. Safety Instructions
Personal safety is of paramount importance. Please follow all safety
instructions when installing ERM products
•Always disconnect power when performing installation by removing the negative
connection of the vehicle battery. Never work when power is connected.
•Always connect the positive wire using a 3A fuse.
•Reconnect the battery only after the installation is fully completed, making sure all
wires are safely insulated.
•Use appropriate work tools.
•Maintain good ventilation and lighting in the work area.
•Never leave bared wires. Trim all wires not in use in such a way that no bare
conductors remain, and fix them securely in place.
•Perform installation in a dry environment.
ERM devices are not water-tight.
•Install ERM devices away from any heat sources.
•Do not install ERM devices in the engine compartment or on the vehicle’s exterior.
•Install ERM devices away from large metallic bodies and never install them in small
gaps between metallic objects.
StarLink TrackerSF Installation Manual
ERM Advanced Telematics page: 4
3. General Instructions
•Install the device with the THIS SIDE UP label facing upwards.
•Make sure no metal objects obstruct the device.
•Use cable ties to hold wires in place and create tidy wire bundles.
•Double-sided adhesive stickers could be used for securing the device in its
selected location.
•Instructions for soldering wires:
a. Strip the ends of the wires to be soldered together.
b. Slide an appropriate length of heat-shrink insulation tubing on to one of the
wires.
c. Solder the wires.
d. Slide the heat-shrink insulation over the solder joint.
StarLink TrackerSF Installation Manual
ERM Advanced Telematics page: 5
e. Use a heater-gun to heat the insulation. The insulation shrinks until it sits
snugly on the solder joint.
f. Tie the wire with a cable tie in such a way as to relieve stress from the new
solder joint.
StarLink TrackerSF Installation Manual
ERM Advanced Telematics page: 6
4. Tools and Equipment/Materials Required
To correctly install the devices and accessories, the following equipment and tools are
required:
Item
Name
Picture
Item
Name
Picture
1
Phillips and flat
Screwdrivers
2
Panel removal tool,
hard plastic
3
Cutter
4
Wire stripper
5
Combination plier
6
Terminal crimper
7
Digital multi-meter
8
Hand torch
9
Cordless drill
10
Gas soldering iron
11
Long-nosed plier
12
Solder
13
Utility knife
14
Wire lugs with star
washers
15
T-type nut drivers
16
Plastic tubing
17
Isolation shrink
wrap tubing
18
Insulation tape
19
Screwdriver bits
StarLink TrackerSF Installation Manual
ERM Advanced Telematics page: 7
5. Installing StarLink Devices
Before beginning installation, make sure your package includes all the following:
This procedure describes the standard connections required to operate StarLink devices.
Two-sided
sticky tape
3A fuse
3A fuse housing
StarLink
device
Strips
StarLink
harness
Two-sided
sticky paper
StarLink TrackerSF Installation Manual
ERM Advanced Telematics page: 8
5.1 Know the StarLink Family of Tracking Devices
1. Unwrap the device wire harness but do not connect it to the device yet.
Refer to the following wiring/color diagram of the StarLink connector
when performing connections in the subsequent steps of this procedure.
Brown wire | 10
Yellow wire | 9
Orange wire | 8
Purple wire | 7
White wire | 6
CAN Low
Port B / Out 2
General output
Port C / Out 3 / In 1
eNet2 (pull-up)
Port D / Out 4 / In 2
Dallas iButton (pull-up)
CAN High
Ground (-)
Port F / In 4 VSS
(pull-down)
PC Communication
LIN
Ignition input
(pull-down)
+12/24V
Black wire | 5
Blue wire | 4
Grey wire | 3
Green wire | 2
Red wire | 1
2. Connect the red wire (pin #1) via a 3A fuse to the vehicle battery
(+12V/+24V). Make sure this positive feed remains live even when the
Ignition switch is turned to OFF and when starting the engine. The fuse
must be removed from the fuse housing during installation.
3. Connect the black wire (pin #5) to the vehicle chassis or any grounded
part of the vehicle (GND).
Make sure the connection is free of paint or dirt to assure a good
conductive ground connection
4. Connect the green wire (pin #2) to the vehicle Ignition switch (IGN).
10 9 8 7 6
5 4 3 2 1
10 9 8 7 6
5 4 3 2 1
StarLink TrackerSF Installation Manual
ERM Advanced Telematics page: 9
Reconnect the vehicle battery and test the ignition (green) wire –you
should measure 0V when the ignition switch is set to OFF and 12V (or
24V) when it is set to ON
5. Gather together all the unused wires and tie them neatly so they do not
interfere with any other parts or systems.
Keep in mind that you may need to use some of the wires in the future
6. Insert the SIM card, as follows:
•Using a small, flat screwdriver, remove the cover of the SIM slot on the
device side.
•Slide the SIM card into the SIM slot and gently push it in (note the SIM
polarity).
•Use a screwdriver to push and lock the SIM card in place.
•Replace the cover of the SIM slot.
StarLink TrackerSF Installation Manual
ERM Advanced Telematics page: 10
7. Plug the harness connector into the device socket.
9. Approximately 10 seconds after powering up the
device, both the red and green LEDs should start
blinking.
The green LED indicates GPS reception.
The RED LED indicates communication with the GSM and a
connection with the server.
Before finally fixing the device in place, make sure it is properly
registered on your server and data has been transmitted as expected
10. To finalize the installation, fix the device in place –Opposite to driving
direction (note the THIS SIDE UP label) with a double-sided adhesive
sticker or with the cable ties threaded through the device side slits. (as
shown on the next page).
11. Reassemble any vehicle components you may have dismantled.
Green LED
Red LED
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Reloj de tiempo de E-RM
Manuales populares de Reloj de tiempo de otras marcas
Easy Clocking
Easy Clocking XENIO 500 Manual
Amano
Amano MTX-15 Manual de usuario
LA CROSSE CLOCK
LA CROSSE CLOCK Harper 404-3450A Manual de usuario
Europa components
Europa components ET167DYD Manual de usuario
TONIN CASA
TONIN CASA Opaca circle Manual de usuario
CS TIMECLOCK
CS TIMECLOCK 2110 Manual de instrucciones