Dynojet WIDEBAND CX Manual de usuario

WIDEBAND CX

INSTALLATION GUIDE

1WIDEBAND CX

1DIAGNOSTIC TO CAN TO POWER

VISION CABLE

1O2 SENSOR

1VELCRO

3ZIP TIE

For Use With Honda Power Vision

PARTS LIST

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION

2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081

800-992-4993 IWB-PV16-1WWW.DYNOJET.COM

IWB-PV16-1 HONDA

INTRODUCTION

INSTALLING THE WELD BOSS AND SENSOR

WIDEBAND CX OVERVIEW

Thank you for purchasing the Wideband CX (WBCX) from

Dynojet Research. The WBCX module is the tuning tool

for gathering Wideband Air Fuel Ratio data for monitoring

engine performance.

Use your Power Vision module to view and log WBCX

data; combine your Wideband data with Dynojet’s Power

Core software to create your perfect tune and achieve

optimal performance from your vehicle.

Note: This WBCX device only pairs with the Power Vision

module for this vehicle.

1 Mock up the O2 sensor installation location on the

exhaust system in a manner that reduces the risk of

moisture contamination on the sensor. Condensation can

build up in the exhaust pipes and potentially damage the

sensor.

2 Ideally, you should orient the weld boss so the sensor

is between the 9 o’clock and 3 o’clock position. A 10°

inclination off the horizontal plane should be considered

a minimum.

Note: Verify you have adequate clearance for the sensor

and wiring harness. Make sure the O2 sensor harness is

as straight as possible. If you must secure the harness

to keep away from danger make sure you do not squeeze

the sheathing of the harness.

3 Mark the sensor installation location and install the weld

boss.

4 Thread the O2 sensor into the weld boss.

5 Connect the O2 sensor cable to the O2 sensor and route

the cable to the WBCX location.

Note: If you must secure the harness to keep away from

danger, make sure you do not squeeze the sheathing of

the harness.

6 Attach the six wires from the O2 Sensor cable to the

screw terminal on the WBCX module.

Note: Piercing the holes with a paperclip will make

inserting the wires easier.

7 Install the terminal strip plug.

WBCX CAN PORT

CONNECT TO

POWER VISION

WBCX TERMINAL STRIP

CONNECT TO O2 SENSOR

WIDEBAND CX OVERVIEW

LOCATIONORIENTATION

WBCX CAN PORT

CONNECT TO

VEHICLE

ATTACH O2 WIRES TO WIDEBAND CX

INSTALLATION GUIDE

INSTALLING THE WBCX

1 Secure the WBCX under the seat near the diagnostic port

using the supplied Velcro. Be sure to clean the mounting

surfaces thoroughly with the supplied alcohol swab.

2 Remove the cable that was included with the Power

Vision from the Diagnostic port of the vehicle

3 Using the supplied cable with the WBCX, connect

one end to the Power Vision and the other end to the

diagnostic port of the vehicle.

4 Connect the ﬂat, 4 pin plug of the cable into the port of

the WBCX module. You can use either port.

Grom Models: the diagnostic port is located under the

seat.

CONNECTING TO THE POWER VISION

1 Following the instructions included with your Power

Vision, secure the Power Vision to the vehicle using the

supplied Velcro. Make sure the Power Vision will not

interfere with the operation of the vehicle.

2 Attach the large connector from the Wideband harness to

the port on the Power Vision. POWER VISION PORT

CONNECT TO WBCX

CONNECT THE WIDEBAND HARNESS

DIAGNOSTIC PORT

PUSH THE LIMIT.

WWW.DYNOJET.COM

Otros manuales de Accesorios para automóviles de Dynojet

Dynojet

Dynojet Power commander V Manual de servicio

Dynojet

Dynojet Power commander V Guía de inicio rápido

Dynojet

Dynojet Power commander V Manual de usuario

Dynojet

Dynojet Power Commander FC Manual de servicio

Dynojet

Dynojet POWER VISION 3 Manual de usuario

Dynojet

Dynojet Power commander V Manual de usuario

Dynojet

Dynojet Power commander V Manual de usuario

Dynojet

Dynojet POWER VISION PV3-2511C Manual de usuario

Dynojet

Dynojet POWER VISION PV3-25-04 Manual de usuario

Dynojet

Dynojet Power commander V Manual de usuario

Dynojet

Dynojet Power Commander III Manual de usuario

Dynojet

Dynojet Power commander V Manual de usuario

Dynojet

Dynojet Power commander V Manual de usuario

Dynojet

Dynojet Power Commander III Manual de servicio

Dynojet

Dynojet Power commander V Manual de usuario

Dynojet

Dynojet Power commander V Manual de usuario

Dynojet

Dynojet Power Commander V 22-027 Manual de usuario

Dynojet

Dynojet Power Commander III USB Manual de usuario

Dynojet

Dynojet power commander III Manual de usuario

Dynojet

Dynojet Power Commander III USB EX Manual de usuario

Dynojet

Dynojet POWER VISION PV3-25-16 Manual de usuario

Dynojet

Dynojet Power commander V Manual de usuario

Dynojet

Dynojet Power commander V Manual de usuario

Dynojet

Dynojet Power commander V Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario