Dwyer Instruments 477A-1 Manual de usuario

Series 477A Digital Manometers are ver-

satile, hand-held, battery operated manome-

ters available in several basic ranges from 0-

20 in. w.c. up to 100 psi. All models measure

either positive, negative or differential pres-

sures with ±0.10% of full scale accuracy. You

can select from up to seven common English

and metric pressure units so conversions are

not necessary. A memory function allows

storage of up to 40 readings for later recall

and a backlight provides auxiliary lighting for

hard-to-see locations. Also standard are a

hold feature plus both visual and audible over-

pressure alarms.

477A-1 0-20.00 in. w.c. 0-4.982 kPa

477A-2 0-40.00 in. w.c. 0-9.96 kPa

477A-3 0-200.0 in. w.c. 0-49.82 kPa

477A-4 0-10.00 psi 0-68.95 kPa

477A-5 0-30.00 psi 0-206.9 kPa

477A-6 0-50.00 psi 0-344.8 kPa

477A-7 0-100.0 psi 0-689.5 kPa

Series 477A Handheld Digital Manometer

Specifications - Installation and Operation Instructions

Bulletin D-26

DWYER INSTRUMENTS, INC.

Phone: 219/879-8000 www.dwyer-inst.com

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A. Fax: 219/872-9057 e-mail: info@dwyer-inst.com

SPECIFICATIONS

Service: Air and compatible gases.

Wetted Parts: Consult factory.

Accuracy: ±0.10% of full scale from 60 to 78°F

(15.6 to 25.6°C); ±1% of full scale from 32 to 60

and 78 to 104°F (0 to 15 .6 and 25.6 to 40°C).

Pressure Hysteresis: ±0.1% of full scale.

Pressure Limits: See chart.

Temperature Limits: 32 to 104°F (0 to 40°C).

Storage Temperature Limits: -4 to 176°F (-20

to 80°C).

Display: 4-digit LCD (.425˝ H x .234˝ W digits).

Resolution: See chart.

Power Requirements: 9 volt alkaline battery.

Battery included but not connected.

Weight: 10.2 oz. (289 g).

Connections: Two barbed connections for use

with 1/8˝ (3.18 mm) or 3/16˝ (4.76 mm) I.D. tubing

for 477A-1, 477A-2, 477A-3, 477A-4 and 477A-5

only. Two compression fittings for use with 1/8˝

(3.18 mm) I.D. x 1/4˝ (6.35 mm) O.D. tubing for

477A-6 and 477A-7 only.

Available Pressure Units:

477A-1 & 477A-2: psi, in. w.c., mm w.c., in.

Hg, mm Hg, Pa, kPa, bar, mbar

477A-3 & 477A-4: psi, in. w.c., mm w.c., in.

Hg, mm Hg, kPa, bar, mbar

477A-5, 477A-6 & 477A-7: psi, in. w.c., in.

Hg, mm Hg, kPa, bar, mbar

Model

Number English

Range Metric

Range

Maximum Pressure

477A-1 3 psi (0.21 bar)

477A-2 3 psi (0.21 bar)

477A-3 15 psi (1.03 bar)

477A-4 30 psi (2.07 bar)

477A-5 60 psi (4.13 bar)

477A-6 100 psi (6.89 bar)

477A-7 200 psi (13.78 bar)

D-26:D-26(478) 7/10/09 10:04 AM Page 1

INSTRUCTIONS

Battery Installation

The unit is shipped with a separate 9 volt alkaline battery which must be installed before

operation. Remove the two screws holding the bottom endcap in place and remove the

endcap. Connect the battery to the enclosed battery clip observing correct polarity. Be

careful not to trap wires between the battery, case or foam pads which retain the battery.

This could make it difficult to install the battery or remove it later for replacement. Be sure

the rubber gasket is properly seated in the gasket channel of the endcap and replace end-

cap. Note that the endcap will only fit one way because the holes are slightly off-center.

Place the “Z” shaped wrist strap clip in one of the screw recesses and replace the screws.

Do not overtighten the screws. Attach wrist strap to clip.

When battery replacement becomes necessary, use only a 9 volt alkaline type such as

a Duracell® MN1604, Eveready®522 or equivalent. Zinc-carbon types, often labeled Heavy-

duty are not recommended because of the increased potential for leakage. Alkaline batter-

ies are also a better value because they last up to three times longer in this device.

On-Off Operation

The on-off control is a toggle function. Press and release the ON/OFF key once to turn

unit on; again to turn it off. If the manometer is left on with no activity for approximately 20

minutes, unit will turn itself off to conserve the battery.

Display Backlight

The Model 477A includes a display backlight to allow use in the dark or in poor lighting con-

ditions. Manometer must be switched off before this feature can be activated. Next, press and

hold the ON/OFF key down. After about 1 second the backlight will come on and remain light-

ed for approximately 2 minutes after which it will turn itself off to conserve battery life.

Zeroing Pressure Reading

Potential inaccuracy due to temperature effects can be minimized by re-zeroing immediately

before use. To zero the display, vent both ports to atmosphere so no pressure is applied to

either port. Press the ZERO/STORE key and - - - - will be momentarily displayed as zeroing

occurs. Zeroing is not possible when the memory mode is in use. It must be done before select-

ing that function.

If the unit is accidently zeroed with pressure applied to one of the ports, the pressure read-

ing might display incorrectly. To correct, vent the pressure ports to atmosphere and press the

ZERO/STORE key to zero the unit.

Pressure Connections

To measure single positive pressure, connect tubing to port marked + and vent oppo-

site port to atmosphere. To measure differential positive pressure, connect higher positive

pressure to port marked + and lower positive pressure to port marked -. Manometer will

indicate the difference between the two.

Selecting Pressure Units

Up to seven pressure units are available. The display will indicate the current selection.

To change to different units, use the UNITS/LOC key. Each touch will cause an advance to

the next choice. The selected units will remain in memory even when power is shut off. This

way, your preference will always be displayed after the initial selection.

D-26:D-26(478) 7/10/09 10:04 AM Page 2

Display Hold

There may be situations where you want to temporarily retain a reading. The Model 477A

includes a Display Hold feature which freezes the current reading and holds it in the display until

cleared. To activate this operation, momentarily press the HOLD/MEMORY key when the pres-

sure you want to save is displayed. A HOLD indicator will appear in the display to indicate that

the reading shown is frozen. To return to normal operation, press the HOLD/MEMORY key

again.The HOLD indicator will disappear and the current pressure will again be shown.

Memory Function

A memory function is included in the Model 477A that allows you to store up to 40 pres-

sure readings for later review or recording. This feature is especially valuable for making a tra-

verse of duct velocity pressures with a Pitot tube or for multipoint pressure measurements. The

readings are stored in non-volatile memory so they will be retained even if the unit is shut off or

the battery is removed.

Storing Pressure Readings

To store a reading, press and hold the HOLD/MEMORY until ST01 is displayed then release

the key. Next, press ZERO/STORE key to save current reading to ST01 memory location. A

beep will sound indicating that the reading has been saved. As each reading is saved, the mem-

ory location display will advance to the next number. To resume pressure measurement, press

the HOLD/MEMORY key again. Note that in the memory mode, the display zero function is not

available. To zero the display, you must first exit the memory mode and then press the

ZERO/STORE key.

Viewing Stored Readings - Selecting a Location

To view the contents of memory, press and hold the HOLD/MEMORY until RD01 is displayed

then release the key. Next, press UNITS/LOC to view other memory location. To resume pres-

sure measurement, press the HOLD/MEMORY key again.

Clearing Memory

To clear the contents of memory, press and hold the HOLD/MEMORY until CLR is displayed

then release the key. Next, press ZERO/STORE key to clear all previously stored readings.

During this operation - - - - will be displayed. Once memory is cleared, the current pressure will

be displayed.

Exiting Memory Mode

To exit the memory mode press the HOLD/MEMORY key again and the unit will return to

normal operation.

D-26:D-26(478) 7/10/09 10:04 AM Page 3

Dampening Function

The dampening feature allows the user to enter a dampening number from 1 to 16 (default

value = 2). Entering a larger number increases the amount of readings that are averaged for

each display update.

In order to access the dampening feature, follow the instructions below:

1. Press and hold the HOLD/MEMORY button. The upper right portion of the LCD scrolls

through a menu selection (HOLD, ST01, RD01, CLR, and DAMP). When “DAMP” is shown,

release the HOLD/MEMORY button. This selects the dampening feature.

2. Once “DAMP” is selected, a number is shown in the upper right portion of the LCD, along

with the current pressure reading. This number is the dampening number. Adjust the number

up by pressing the ZERO/STORE button or down by pressing the UNITS/LOC button. The LCD

update rate slows as the number increases from 1 to 16. Therefore, for best results, choose the

smallest number that provides a stable pressure reading.

Once the pressure reading is stable, press and release the HOLD/MEMORY button to store the

dampening value.

Overpressure Alarm

A visual indicator and audible alarm are provided to alert the operator that pressure has

exceeded the operating range of the unit. Exceeding the range will not damage it or affect

calibration as long as the maximum rated pressure is not exceeded. Do not exceed the

maximum rated pressure of the manometer. Doing so will cause permanent damage

to the sensor, may rupture the housing and/or cause injury.The maximum pressure is

shown on the rear label and on page 1 of these instructions.

Low Battery Indicator

A weak battery can cause improper operation or inaccurate measurements. A low battery

indicator is provided on the display to show when the battery needs replacement. Although the

unit might appear to function and indicate properly, the accuracy of readings cannot be guar-

anteed when the LOW BAT indicator is illuminated. Replace the battery with a fresh one. Do not

leave an exhausted battery in the unit due to potential leakage.

MAINTENANCE

The Series 477A handheld digital manometers are not field repairable and should be returned

if repair is needed (field repair should not be attempted and may void warranty). Be sure to

include a brief description of the problem plus any relevant application notes. Contact customer

service to receive a return goods authorization number before shipping.

Duracell® is a registered trademark of The Gillette Company

Everready®is a registered trademark of The Everready Battery Company, Inc.

DWYER INSTRUMENTS, INC.

Phone: 219/879-8000 www.dwyer-inst.com

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A. Fax: 219/872-9057 e-mail: info@dwyer-inst.com

D-26:D-26(478) 7/10/09 10:04 AM Page 4

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Dwyer Instruments

Dwyer Instruments

Dwyer Instruments AP2 Manual de usuario

Dwyer Instruments

Dwyer Instruments DCG Series Manual de usuario

Dwyer Instruments

Dwyer Instruments 1205A-5 Manual de usuario

Dwyer Instruments

Dwyer Instruments Series 2-5000 Minihelic II Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments SLR-01 Manual de usuario

Dwyer Instruments

Dwyer Instruments 477B-1 Manual

Dwyer Instruments

Dwyer Instruments 250-AF Series Manual de usuario

Dwyer Instruments

Dwyer Instruments DPMP-5 Series Manual de usuario

Dwyer Instruments

Dwyer Instruments 485-2 Instrucciones de funcionamiento

Dwyer Instruments

Dwyer Instruments SAH-22-IN Manual de usuario

Dwyer Instruments

Dwyer Instruments TUF series Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments DPMA-5 Series Manual de usuario

Dwyer Instruments

Dwyer Instruments 450 Series Manual de operación y mantenimiento

Dwyer Instruments

Dwyer Instruments 45158 Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments 450A-1 Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments Rate-Master RMV II Series Manual de usuario

Dwyer Instruments

Dwyer Instruments Love Controls LCT216 Series Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments TUF Series Manual de usuario

Dwyer Instruments

Dwyer Instruments SCC-POT/C Manual de usuario

Dwyer Instruments

Dwyer Instruments Series APM Manual de usuario

Dwyer Instruments

Dwyer Instruments THI2-10 Manual de usuario

Dwyer Instruments

Dwyer Instruments 485B Instrucciones de funcionamiento

Dwyer Instruments

Dwyer Instruments Slack-Tube 1211-8 Manual de operación y mantenimiento

Dwyer Instruments

Dwyer Instruments 660 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario