Dwyer Instruments 1430 Manual de usuario

Model 1430 Microtector

Electronic Point Gage

Installation and Operating Instructions

Model 1430 Microtector®Portable

Electronic Point Gage combines mod-

ern, solid-state integrated circuit elec-

tronics with a time-proven point gage

manometer to provide fast, accurate

pressure measurements.

SPECIFICATIONS AND FEATURES

•Accurate and repeatable to ± .00025

inches water column

•Pressure range: 0 - 2˝ w.c., positive,

negative, or differential pressures

•Non-toxic and inexpensive gage fluid

consists of distilled water mixed with

a small amount of fluorescein green

color concentrate

•Convenient, portable, lightweight

and self-contained, the unit requires

no external power connections and

is operated by a 1.5 volt penlight cell

•A.C. detector current eliminates

point plating, fouling and erosion

•Micrometers are manufactured in accor-

dance with ASME B89.1.13-2001, and

are traceable to a standard at the National

Institute of Standards and Technology

• Three-point mounting, dual leveling

adjustment, and circular level vial

assure rapid setup

• Durablock precision-machined acrylic

plastic gage body

• Sensitive 0 - 50 microamp D.C. meter

acts as a detector and also indicates

battery and probe condition

• Heavy 2˝ thick steel base plate

provides steady mounting

• Top-quality glass epoxy circuit board

and solid-state, integrated circuit

electronics

• Electronic enclosure of tough, molded

styrene acrylonitrile provides maximum

protection to components yet allows

easy access to battery compartment

• Rugged sheet steel cover and carrying

case protects the entire unit when not

in use

• Accessories included are (2) 3-foot

lengths Tygon tubing, (2) 1/8˝ pipe

thread adapters and 3/4 oz. bottle of

fluorescein green color concentrate

with wetting agent

Maximum pressure: 100 psig with

optional pipe thread connections.

Bulletin D-57

Patent No. 3,726,142

D-57 10/5/05 3:59 PM Page 1

Precision Pressure Measurement

The Dwyer Microtector®combines the time-

proven principles of the Hook Gage type

manometer and modern solid-state integrat-

ed circuit electronics. It provides an inexpen-

sive means of achieving accuracy and

repeatability within ± .00025 inches water col-

umn throughout its 0 to 2 inches w.c. range.

It is truly a new standard in precision measur-

ing devices.

Principles of Operation

A pressure to be measured is applied to the

manometer fluid which is displaced in each

leg of the manometer by an amount equal to

1/2 the applied pressure. A micrometer

mounted point is then lowered until it contacts

the manometer gage fluid. The instant of con-

tact is detected by completion of a low-power

A.C. circuit. Current for this circuit is supplied

by a 1.5 volt penlight cell feeding two semi-

conductor amplifiers which act as a free-run-

ning multivibrator operating at a frequency of

approximately two kilohertz. Completion of

the A.C. circuit activates a bridge rectifier

which provides the signal for indication on a

sensitive (0 to 50 microamps) D.C. microam-

meter.

LOW

PRESSURE

FLUID

LEVEL

OFF ON

On indication of contact, the operator stops

lowering the point and reads the micrometer

which indicates one half the applied pressure.

By interpolating eight divisions (each being

.000125˝ w.c.) between .001 micrometer

graduations, a total accuracy of .00025 can

easily be achieved. The micrometer complies

with Federal Specification GGG-C-105A and

is traceable to a master at the NIST.

Locating and Opening

Stand the Microtector®and case on a firm flat

level surface. Remove cover by releasing the

latches and lifting it straight up. If it is neces-

sary to move the gage without case, handle

only the base plate or clear acrylic block.

(CAUTION: Do not handle gage by grasping

meter-electronic package housing Item 7 on

drawing.)

Microtector

Gage

D-57 10/5/05 3:59 PM Page 2

Fluid Level

Level the gage by adjusting the two front lev-

eling screws (Item 8 on drawing) until the bub-

ble in the spirit level is centered in the small

circle. After leveling the gage, open both

rapid shut-off valve tube connectors (Items 2

and 5). Back off the micrometer (Item 4), if

necessary, to make sure that the point is not

immersed in the gage fluid. The fluid level in

the gage should now coincide with the mark

on the right hand bore (Item 6) plus or minus

approximately 1/32 inch. If the level of fluid is

too high, fluid can be removed with an eye

dropper pipette or carefully poured out of the

right connection (Item 5).

If the level is too low, remove the top left rapid

shut-off valve tube connector(Item 2) and add

distilled water pre-mixed with the proper

amount of Dwyer green concentrate. (See

maintenance instructions for proportions.

After correcting the fluid level, re-install the

rapid shut-off connectors and, with these in

the open position, re-level the Microtector®.

The gage is now ready to be zeroed.

Zeroing

Turn the Micrometer barrel (Item 4) until its

lower end just coincides with the zero mark

on the scale and the zero on the barrel scale

coincides with the vertical line on the internal

scale. Note that the internal scale is graduat-

ed every .025˝ from 0 to 1.00 inch and the

barrel scale is graduated in one thousandths

from 0 to .025˝. Turn the meter circuit switch

at the top of gage to the “on” position. While

holding the barrel at the zero position (and

with gage level), raise or lower the point by

turning the knurled knob (Item 3) until the

point is above, but near, the fluid.

Check to be sure that the meter registers

zero. Watch the meter, hold the barrel, and

lower the point slowly by turning the top

knurled knob. As the knob is turned, the

point will contact the fluid and the meter

pointer will move from zero to some upscale

position.

After making contact, turn the point out of the

fluid by turning the micrometer barrel counter-

clockwise to a reading of .010 or more.

Again, watch the meter and, this time, lower

the point by turning the micrometer barrel.

The point position where the meter pointer

begins to move up scale is the zero position.

This position should correspond to the zero

reading on the micrometer. Adjust the point in

relation to the micrometer barrel by turning

the top knob while holding the barrel steady.

Repeat lowering the point, watching the

meter for contact, and adjusting the point

until the zero position and zero reading exact-

ly coincide. The gage is now zeroed and

should not be moved.

An alternative method of zeroing and reading

can be used wherein, instead of zeroing the

gage completely, a zero correction reading is

taken and recorded, then subtracted from the

final reading. Comparable results can be

obtained with either method.

Positive Pressure Measurement

With the fluid at its proper level, a pressure of

2.0˝ water column maximum can be meas-

ured. Positive pressure should be applied to

the top left connection (Item 2) with the

micrometer zeroed as described above. This

will permit a simple direct reading to be taken.

After an unknown pressure has been applied

at the top left connection, the fluid level will

drop in the left bore and rise over the point in

the right bore. Note that the indicating meter

point has moved upscale because the point is

immersed in the fluid. Turn the micrometer

counter-clockwise until the point leaves the

fluid as indicated by the meter pointer drop-

ping to zero on its scale. Then slowly turn the

micrometer down until its point just touches

the fluid surface, causing movement of the

meter pointer. Withdraw the point and repeat

several times, noting each time the microme-

ter reading where the meter pointer begins.

The average of these readings multiplied by

two is the pressure applied to the gage. (Avg.

reading x 2 = pressure applied in inches w.c.

The degree of uncertainty for the operator is

indicated by the difference in these readings.

D-57 10/5/05 3:59 PM Page 3

When the readings are complete, the pres-

sure should be removed and the zero setting

of Microtector®rechecked. Any change in the

zero position will indicate inaccurate readings.

Should this happen, the zero-set and pres-

sure measurement procedure should be

repeated.

Negative Pressure

or Vacuum Measurement

Zero the gage. Connect the source of vacu-

um or negative pressure to the right-side

gage connection (Item 5) and proceed as

described under Positive Pressure

Measurement section. Remember that the

pressure measured in this way is negative.

Differential Pressure Measurement

Differential pressures may be measured by

connecting the higher (more positive) pres-

sure to the left connection (Item 2) and the

lower pressure to the right connection (Item

5).

Storage

Turn meter circuit switch to “off” position and

withdraw the point well clear of fluid (by turn-

ing micrometer clockwise) when gage is not in

use. This will conserve the batteries and min-

imize build-up of oxides, etc., on the point.

Keep the unit covered and in an area free of

strong solvent fumes.

Maintenance

When the meter reading becomes reduced or

the pointer movement gets sluggish (with the

circuit on and the point in fluid), the following

should be done:

(1) Remove the point (by unscrewing) and

clean the tip lightly using fine crocus cloth.

Wipe off all grit and dirt with a clean rag;

reassemble and recheck meter operation.

(2) If the meter operation continues to be

sluggish, replace the size AA, 1.5 volt battery.

(Replace the battery at least once a year to

avoid deterioration of battery and damage to

gage. Leakproof alkaline battery is recom-

mended.)

To replace the battery, remove center screw

(Item 10) located in the back of the electronic

enclosure. Cover (Item 9) will come off,

exposing the battery. Pull the old battery out

and push a new battery into the battery hold-

er with the positive (center) terminal to the

right (to the end marked with + on the holder).

If the fluid becomes contaminated and

requires replacement: empty old fluid from

gage; flush out with clear water and replace

with distilled water and Dwyer A126 fluores-

cein green color concentrate mixed with 3/4

oz. concentrate to each quart of water.

CAUTION:

1. Do not substitute other gage fluids, as

proper gage operation depends on use of the

specified gage fluid to provide proper surface

tension, wetting ability and electrolyte capa-

bility with unity specific gravity.

If the gage bore is very dirty, a mild soap solu-

tion may be used to aid in cleaning prior to

flushing with clear water.

2. Do not clean with liquid soaps, special sol-

vent, de-greasers, aromatic hydrocarbons,

etc. Such cleaners and solvents may contain

chlorine, fluorine, acetone and related com-

pounds that will permanently damage the

gage and prevent proper operation.

D-57 10/5/05 3:59 PM Page 4

Otros manuales de Instrumento de medición de Dwyer Instruments

Dwyer Instruments

Dwyer Instruments UF35 Manual de usuario

Dwyer Instruments

Dwyer Instruments 490W Series Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments 471-2 Manual de usuario

Dwyer Instruments

Dwyer Instruments DPMW Series Manual de usuario

Dwyer Instruments

Dwyer Instruments 45158 Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments 485B Instrucciones de funcionamiento

Dwyer Instruments

Dwyer Instruments GFM2 Series Manual de usuario

Dwyer Instruments

Dwyer Instruments RSM Series Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments IC-VP2 Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments DFMT Series Manual de usuario

Dwyer Instruments

Dwyer Instruments Mark II 40 Manual de usuario

Dwyer Instruments

Dwyer Instruments PHO-1 Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments BPI Series Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments 160S series Manual de usuario

Dwyer Instruments

Dwyer Instruments UFC Series Manual de usuario

Dwyer Instruments

Dwyer Instruments SPPM Series Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments 477A-1 Manual de usuario

Dwyer Instruments

Dwyer Instruments 477AV-000 Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments EC2-10 Manual de usuario

Dwyer Instruments

Dwyer Instruments CSG Manual de usuario

Dwyer Instruments

Dwyer Instruments 1207A Manual de usuario

Dwyer Instruments

Dwyer Instruments 25 Manual de operación y mantenimiento

Dwyer Instruments

Dwyer Instruments Series APM Manual de usuario

Dwyer Instruments

Dwyer Instruments DPMA-4 Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario