DV8 OFFROAD FDBR-01 Manual de usuario

6400 SYCAMORE CANYON BLVD.

RIVERSIDE, CALIFORNIA 92507

855-680-9595

WWW.DV8OFFROAD.COM

PRODUCT

INSTALLATION MANUAL

BRONCO TUBE FENDERS

2021+ FORD BRONCO

FDBR-01

TOOLS REQUIRED SKILL LEVEL TIME REQUIRED

-#4 Allen Bit

-7mm, 10mm Wrench/Socket

-Phillips Head Screw Driver

-Razor

Before you install this kit — Read and understand all

instructions, warnings, cautions, and notes contained in

this installation instruction guide. Consult your vehicle

owner’s manual for proper disconnection of electrical and

lifting of vehicle if required for installation of this product.

This install may require some technical skills and

knowledge of basic mechanical work. If you do not feel that

you are capable of performing this install please take this

product to a trained professional.

After reading this guide please contact us with any

questions or concerns before installing product.

Customer Service: 855-680-9595

DV8 Offroad is not responsible for any bodily injury or harm to you

or your vehicle as a result of an improper install.

Proper installation of this kit required knowledge of the factory

recommended procedures for removal and installation of original

equipment components. We recommend that the factory shop manual

and any special tools needed to service your vehicle be on hand during

the installation. Installation of this kit without proper knowledge of the

factory recommended procedures may affect the performance of these

components and the safety of the vehicle

• Always wear eye protection when operating power tools

Inspect all contents of this package to make sure product is not damaged

and all installation hardware has been included. If parts are missing from

kit, please be prepared to provide the following information

1. Name of purchase location

2. Bar Code on side of box

3. Date above bar code

4. Date inside box cover

- Novice/Intermediate

- 1 (you) to 2 persons

Little skill level required, you can

easily install it by yourself however,

additional help will be useful

- 2 Hours

Time to install this should only

take about two hours

WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION

855-680-9595

NEED HELP?

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 1 | Starting with the front,

begin by removing the factory fender.

These are easily removed by twisting the

small latches until latch becomes loose.

Once all are loose, pull fender away from

Bronco until hidden clips release.

Note: These should pull away from the Bronco

easily. If they are hard, adjust latches.

Begin by unpacking all items and

inspecting for missing pieces or damage. If

you have any concerns, please contact the

company the product was purchased from.

-(18) M6x30mm Bolts

-(18) M6 Flat Washers

-(18) M6 Nuts

-(4) Fender “P” Seals

HARDWARE INCLUDED

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 2 | Once fender is removed, use

a Phillips screwdriver and 7mm socket

and remove the plastic push pins along

the front and back outer edge of the inner

fender.

Note: You do not need to remove the inner

fender, you only need to gain access to the

fender mounting holes.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 3 | Moving to the fender,

remove the rubber cover off the stud.

Locate the seal that matches the fender.

This can be done by laying the seal on the

fender and aligning the holes in the seal

with the holes in the fender.

Peel back the tape and apply rmly to the

fender. The round part of the seal should

be resting on top of the plate of the

fender.

Note: The seals may be longer than the

fender, but these will be trimmed later on.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 4 | Using the M6 hardware, a #4

allen and 10mm wrench/socket, loosely

install fender to vehicle.

Note: Our nuts are serrated, so once nger

tight, you can tighten from the allen head

without having to hold the nut with a wrench.

STEP 5 | Once all fender hardware is

installed, align the fender of the vehicle

and secure hardware.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 6 | Reinstall your inner liner

hardware using the 7mm socket/wrench

and Phillips head screw driver.

Repeat steps for opposite side.

STEP 7 | The rear will be similar to

the fronts by removing the factory fender.

These are easily removed by twisting the

small latches until latch becomes loose.

Once all are loose, pull fender away from

Bronco until hidden clips release.

Note: These should pull away from the Bronco

easily. If they are hard, adjust latches.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 8 | Once fender is removed, use

a Phillips screwdriver and 7mm socket

and remove the plastic push pins along

the front and back outer edge of the inner

fender.

Note: You do not need to remove the inner

fender, you only need to gain access to the

fender mounting holes.

STEP 9 | After installing the seal

onto the rear fender in the same fashion,

mount onto vehicle using #4 allen, 10mm

wrench/socket with M6 hardware.

You can pull back the inner fender to

access the backside of the hardware.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 10 | For the stud on the rear

fender, we recommend using a short

10mm socket for best access.

Align fender to vehicle and secure all

hardware.

STEP 11 | Reinstall all hardware for

inner liners using 7mm wrench/socket

and Phillips head screw driver.

Repeat for other side.

STEP 12 | After all fenders are

installed, using a sharp razor, trim any

excess seal to preference making sure to

cut towards the fender, not the body to

avoid damage to the vehicle.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 13 | Congratulations, you are

now nished with your install of the DV8

Tube Fenders!

Otros manuales de Accesorios para automóviles de DV8 OFFROAD

DV8 OFFROAD

DV8 OFFROAD SPBR-01 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD OE PLUS SRJK-09 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SRBR-06 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD RRJK-03 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SRBR-03 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD D-JP-180011-BK Manual de usuario

DV8 OFFROAD

DV8 OFFROAD FS-15 Series Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SPBR-05 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD MPJL-01 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD WINCH POCKET FAIRLEAD Manual de usuario

DV8 OFFROAD

DV8 OFFROAD CCJL-01 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD D-JP-181112-BK Manual de usuario

DV8 OFFROAD

DV8 OFFROAD STJL-05 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD D-JP-180014-STR4 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD MPGX-02 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SPEC Series Manual de usuario

DV8 OFFROAD

DV8 OFFROAD D-JL-180014-SIL4 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD FDJL-07 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SPEC Series Manual de usuario

DV8 OFFROAD

DV8 OFFROAD LPBR-04 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD D-JP-190024-BLK Manual de usuario

DV8 OFFROAD

DV8 OFFROAD LPBM-03 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SRGX-02 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD OE PLUS SRBR-05 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario