DV8 OFFROAD FDJL-07 Manual de usuario

6400 SYCAMORE CANYON BLVD.

RIVERSIDE, CALIFORNIA 92507

855-680-9595

WWW.DV8OFFROAD.COM

PRODUCT

INSTALLATION MANUAL

SLIM FENDERS

2018+ JEEP WRANGLER JL

FDJL-07

TOOLS REQUIRED SKILL LEVEL TIME REQUIRED

- Trim Clip Tool

- 4, 5mm Allen Bit

- 4mm “L” Shaped Allen Tool

- 10, 12, 13mm Wrench

- Angle Grinder or Cutting Tool of Choice

- Spray Paint

- Zip Ties (Optional)

Before you install this kit — Read and understand all

instructions, warnings, cautions, and notes contained in

this installation instruction guide. Consult your vehicle

owner’s manual for proper disconnection of electrical and

lifting of vehicle if required for installation of this product.

This install may require some technical skills and

knowledge of basic mechanical work. If you do not feel that

you are capable of performing this install please take this

product to a trained professional.

After reading this guide please contact us with any

questions or concerns before installing product.

Customer Service: 855-680-9595

DV8 Offroad is not responsible for any bodily injury or harm to you

or your vehicle as a result of an improper install.

Proper installation of this kit required knowledge of the factory

recommended procedures for removal and installation of original

equipment components. We recommend that the factory shop manual

and any special tools needed to service your vehicle be on hand during

the installation. Installation of this kit without proper knowledge of the

factory recommended procedures may affect the performance of these

components and the safety of the vehicle

• Always wear eye protection when operating power tools

Inspect all contents of this package to make sure product is not damaged

and all installation hardware has been included. If parts are missing from

kit, please be prepared to provide the following information

1. Name of purchase location

2. Bar Code on side of box

3. Date above bar code

4. Date inside box cover

- Intermediate

- 1 (you) to 2 persons

Little skill level required, you can

easily install it by yourself however,

additional help will be useful.

- 2.5 Hours

Time to install this should only

take about two and a half hours.

WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION

855-680-9595

NEED HELP?

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 1 | Use a 10mm socket to

remove the bolts along the top and at the

front of the inner fender.

Use a trim clip tool to remove the clips on

interior of the inner fender.

Use a trim clip tool to remove the clips

running along the outside, securing the

inner fender to the vehicle.

Remove inner fender by pulling down,

then out.

Note: Pictured are un-install and installation of

the passenger side fender.

FRONT UNINSTALL

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 2 | Unplug the turn signal

indicator by pulling the red release tab

out and pulling.

STEP 3 | Use a 10mm socket to

remove the bolt securing the fender to the

vehicle.

Then, remove the fender by pulling away

from the vehicle to release the clips.

Be sure to pull “straight” away from the

vehicle to avoid breaking clips.

STEP 4 | Use a trim clip tool to

remove the factory clips along the fender.

Repeat process for the other side.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 5 | Use a trim clip tool to

remove the clips located along the interior

of the inner fender.

Then remove the clips securing the inner

fender to the vehicle running along the

outside edge of the fender are.

Remove fender by pulling down then out.

REAR UNINSTALL

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 6 | Remove the fender are by

pulling directly away from the vehicle.

Be sure to pull “straight” away from the

vehicle to prevent breaking clips.

STEP 7 | Use a trim clip tool to

remove the clips along the edge of the

fender.

Repeat process for the other side.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 8 | Cut the front fender mount

off and grind it down so it is ush with

the vehicle. Paint is recommended on the

bare steel to prevent rust.

While this step may not be 100%

necessary for tment, we highly

recommend doing this step to achieve the

best look possible.

STEP 9 | Install the provided

nutserts using a nutsert tool. If you do not

own a nutsert tool, we provide one with

our kit.

For instructions on how to use the nutsert

tool, scroll to the last page.

Tip: Hold up the fender the vehicle as a guide to

determine which holes require a nutsert.

FRONT INSTALL

Begin by unpacking all items and inspecting

for missing pieces or damage. If you have any

concerns, please contact the company the

product was purchased from. Extra hardware

may be included with the product.

(40) M6x20 Allen

(4) M8x15 Allen

(40) M6 Nutserts

(40) M6 Flat Washers

(20) M6 Serrated Nuts

(4) M8 Serrated Nuts

(4) M8 Flat Washers

(1) Nutsert Tool

HARDWARE INCLUDED

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 10 | Install the gaskets onto

the fender.

The gaskets are notched to line up with

the mounting holes on each fender.

STEP 11 | Install the fender are

onto the vehicle using the provided

M6x20 hardware with a 4mm allen bit.

Secure the mounting supports using the

supplied M6 hardware with a 4mm allen

bit and 10mm wrench.

During install, check the gasket on the

fenders and tuck away any extra gasket

using a trim clip tool.

Note: Assistance is recommended to prevent

injury and damage to the product or vehicle.

STEP 12 | Route and secure the

wiring to your preference and install the

new turn signal into the factory connector.

Repeat process for the other side.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 13 | Use the provided nutsert

tool with 13mm wrench and 10mm socket

to install the provided nutserts.

Tip: Place the fender on the vehicle as a guide to

determine which holes require a nutsert.

Install the fender are

onto the vehicle using the provided M6

hardware with a 4mm allen bit.

Note: Assistance is recommended to prevent

injury or damage to the product and vehicle.

Double check all hardware is secure.

Repeat process for other side.

REAR INSTALL

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 14 | Check the gasket on both

fenders after install and tuck away any

extra gasket using a trim clip tool.

Double check all hardware is secure and

function of lights and turn signals.

NOTE: If the Jeep was not equipped with OEM

LED lighting, then aftermarket/dealership

programming may be necessary to access all

LED functions.

Repeat process for other side.

STEP 15 | Congrats! You are nished

with the install of the 2018+ Jeep Wrangler

JL Slim Fenders!

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 16 | To use the nutsert tool,

slider the M6 washer and spacer onto the

provided M6x50 bolt.

Then install a nutsert onto the exposed

threads by hand.

STEP 17 | Slide the nutsert tool

with the nutsert into the mounting hole.

Ensure the ange of the nutsert is at

against the vehicle prior to tightening.

STEP 18 | Use a 13mm wrench to

hold the spacer while tightening with

a 10mm socket. Tighten slowly until

the nutsert is set properly. Do not over

tighten.

Nutsert should be “crushed” against the

inside of the fender so that it is tight and

secure.

When nished remove the nutsert tool

using a 10mm socket and repeat as

needed.

Note: Be sure to hold the spacer tight so it does

not move and scratch paint.

Otros manuales de Accesorios para automóviles de DV8 OFFROAD

DV8 OFFROAD

DV8 OFFROAD D-JP-180014-STR4 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD CMJL-01 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD WINCH POCKET FAIRLEAD Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SPBR-05 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SRJK-08 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD RBJL-13 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD D-JP-181112-BK Manual de usuario

DV8 OFFROAD

DV8 OFFROAD FBDR1-05 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD FDJK-07 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD FDGL-06 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SRBR-03 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD TSBR-01 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SPBR-01 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SPEC Series Manual de usuario

DV8 OFFROAD

DV8 OFFROAD LPBM-02 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD OE PLUS SRBR-05 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD CCBR-01 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD ABJL-01 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD STJL-05 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD MPT3-01 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD SRGX-02 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD RRUN-03 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD RBJL-12 Manual de usuario

DV8 OFFROAD

DV8 OFFROAD LPBR-05 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario