DURKOPP ADLER 755 Manual de funcionamiento

755/756

Additional Instructions

Tape feeder

Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,

including extracts, is prohibited without the prior written approval of Dürkopp Adler AG.

IMPORTANT

READ CAREFULLY BEFORE USE

KEEP FOR FUTURE REFERENCE

Table of Contents

Additional Instructions 755/756 - 00.0 - 10/2018 1

1 General information ................................................................... 3

2 Tape feeder ................................................................................. 4

2.1 Assembling and connecting the tape feeder ................................ 4

2.2 Setting the height of the tape feeder ............................................ 9

2.3 Aligning the tape roll holder ........................................................ 10

2.4 Inserting the reinforcement strip ................................................. 11

2.5 Setting up the tape feeder in the software.................................. 13

Table of Contents

2Additional Instructions 755/756 - 00.0 - 10/2018

General information

Additional Instructions 755/756 - 00.0 - 10/2018 3

1 General information

Components of the kit

Check whether the scope of delivery for kit 0755 590904 VES is correct

prior to installation.

Part number Quantity Designation

0755 512454 1 Toothed belt drive

0755 512444 1 Tape feeder

0217 000775 2 Tension spring

9202 002097 2 Cylinder-head bolt M4x16

9205 101877 2 Threaded pin M4x8

9202 002537 2 Cylinder-head bolt M5x35

9330 000097 6 Washer

9202 002487 4 Cylinder-head bolt M5x12

0755 512514 1 Guide carrier

0755 590914 1 Roll holder

9710 063411 2 Magnet valve

0798 120401 1 Cord clip

0755 512613 1 Suction pipe

0755 400990 1 Bracket

0755 591714 1 Dual SM card

0791 755700 EN 1 Additional Instructions

Tape feeder

4Additional Instructions 755/756 - 00.0 - 10/2018

2 Tape feeder

2.1 Assembling and connecting the tape feeder

Fig. 1: Assembling and connecting the tape feeder (1)

To assemble and connect the tape feeder:

1. Connect pneumatic hoses (1) and (2) to the tape feeder.

• blue: Cut tape (finish cutting)

• red: Cut tape (start cutting)

2. Use the connecting piece to connect pneumatic hose (3) with the

transparent hose of the tape feeder.

• gray: Press on/loosen tape

3. Remove the fabric sliding plate.

4. Swivel up the machine head.

(1) - Pneumatic hose

(2) - Pneumatic hose (3) - Pneumatic hose

①

②

③

Tape feeder

Additional Instructions 755/756 - 00.0 - 10/2018 5

Fig. 2: Assembling and connecting the tape feeder (2)

5. Insert the tape feeder.

6. Tighten screws (4) and (5).

7. Use clips to assemble pneumatic hoses (1), (2) and (3) to the plate (6).

Important

Make sure pneumatic hoses (1), (2) and (3) do NOT rest on the machine

head centering device (7) when you fold down the machine head.

8. Guide pneumatic hoses (1), (2) and (3) under the machine head and

fix them in place at the existing cables using cable ties.

(1) - Pneumatic hose

(2) - Pneumatic hose

(3) - Pneumatic hose

(4) - Screws

(5) - Screws

(6) - Plate

(7) - Machine head centering device

⑤

④

⑦

①

②

③

⑥

Tape feeder

6Additional Instructions 755/756 - 00.0 - 10/2018

Fig. 3: Assembling and connecting the tape feeder (3)

9. Assemble the guide rail (8).

10. Connect the cable (9) with the plug.

Fig. 4: Assembling and connecting the tape feeder (4)

11. Assemble the circuit board (10) and connect it to the control using

the CAN cables (12).

12. Assemble the valves (11) on top of the valve block.

(8) - Guide rail (9) - Cable

⑨

⑧

(1) - Pneumatic hose

(2) - Pneumatic hose

(3) - Pneumatic hose

(10) - Circuit board

(11) - Valves

(12) - CAN cables

⑫

⑩

①

②

③

⑪

Tape feeder

Additional Instructions 755/756 - 00.0 - 10/2018 7

13. Connect pneumatic hoses (1), (2) and (3) at the magnet valve block.

•blue(1): Y103 - 2

• red (2): Y103 - 4

• blanking plug: Y104 - 2

•gray(3): Y104 - 4

Fig. 5: Assembling and connecting the tape feeder (5)

14. Assemble the tape roll holder (14).

15. Fit the pneumatic hose (13) for the tape puller and lay it below

the machine.

16. Use cable ties and clips to fix the pneumatic hose (13) in place.

(13) - Pneumatic hose (14) - Tape roll holder

⑫

⑬

Tape feeder

8Additional Instructions 755/756 - 00.0 - 10/2018

Fig. 6: Assembling and connecting the tape feeder (6)

17. Remove the valve cover.

18. Swivel up the machine head.

19. Lay the pneumatic hose (13) through the machine arm from below.

20. Use a Y-connection (15) to connect the pneumatic hose (13) to a hose

of valve X814.

21. Place the valve cover.

22. Swivel down the machine head.

(13) - Pneumatic hose (15) - Y-connection

⑮

⑬

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Máquina de coser de DURKOPP ADLER

DURKOPP ADLER

DURKOPP ADLER 745-34 - Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 745-34 - Instrucciones de funcionamiento

DURKOPP ADLER

DURKOPP ADLER 887 Series Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 969 Classic Instrucciones de funcionamiento

DURKOPP ADLER

DURKOPP ADLER H868 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 396-BT Series Guía

DURKOPP ADLER

DURKOPP ADLER 745-35S Guía de referencia

DURKOPP ADLER

DURKOPP ADLER 610-01 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 838 Instrucciones de funcionamiento

DURKOPP ADLER

DURKOPP ADLER DAC classic 271 Guía

DURKOPP ADLER

DURKOPP ADLER 697 Manual de lista de piezas

DURKOPP ADLER

DURKOPP ADLER 171 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 670 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER H-Type 969 Instrucciones de funcionamiento

DURKOPP ADLER

DURKOPP ADLER M-TYPE DELTA Manual de funcionamiento

DURKOPP ADLER

DURKOPP ADLER DAC BASIC - CLASS 271 PART II V 12-2010 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 911-211-10 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 805 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 7700 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 867 Instrucciones de funcionamiento

DURKOPP ADLER

DURKOPP ADLER 911 Guía del producto

DURKOPP ADLER

DURKOPP ADLER 171 Instrucciones de funcionamiento

DURKOPP ADLER

DURKOPP ADLER 745-34-2 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 504 Guía

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario