DURKOPP ADLER 745-35S Guía de referencia
Quick Reference Card 745-35S
© Dürkopp Adler AG 0791 745400 EN - 0.0 - 0/201
Switch on
P+F
Setting programs
301 Indicating/Deleting
302 Setting the bobbin thread counter
303 Testing the feeding process
304 Step by step mode
305 Dongle menu
Fshort
Sequence on/off
Flong
Sequence new create
ESC +
Displaying the counter of pieces/Deleting
ESC +
Center knife on/off
-
CRUQHr knife on/off
ESC ++
ESC +
Stacker on/off
+-
or
Changing the current seam length
or
Changing over to the next seam program
Sewing mode
Quick Reference Card 745-35S
© Dürkopp Adler AG 0791 745400 EN - 01.0 - 04/2016
Error/Info Description Remedy
3210 Thread breakage Thread in the thread again
3215 Empty bobbin (Bobin thread counter) Insert a full bobbin
3220 Empty bobbin (Remaining thread-monitor)
9601 Pedal has been stepped back during the sewing process For cancelling the pedal has be actuated once again.
Afterwards the feeding clamp runs in ist rear position.
9604 Folder not in top position LigKt-barrier (S4) for fabric removal inactive Adjust light-barrier (S4) for fabric removal
9700 Folder not in top position Correct folder adjustment
(mechanical collision; check switch S8)
9701 Folder not in low position Correct folder adjustment
(mechanical collision; check switch S8)
9720 Error when scanning the fl ap by ligKW-barrier Check the refl ecting foil; check aligment of the ligKW-barrier
9721 Flap has been pos. in front of the front positioning point Position the fl ap correctly
9722 Flap protrudes from the max. sewing area (behind the rear positioning point) Check the fl ap size; Sosition the fl ap correctly
9723 Fluff at the fl ap beginning Feed fl aps with smooth edges; check the refl ecting foil
9726 Flap too large or refl ecting foil soiled or defective Check fl ap size and refl ecting foil
9730 Corner knife at the seam beginning cannot be driven to Alter L1 (adjust corner knife distance) or change
positioning point of the current seam
9001 Corner knife station is swung out
Folding station is swung out during the sewing process
Step back on the pedal; afterwards the transport carriage runs to the back;
start the process.
6ZLQJLQFRUQHUNQLIHVWDWLRQ
Check/adjust fastening of the coUner knife station
9002 Folding station is swung out
Folding station is swung out during the sewing process
Step back on the pedal; afterwards the transport carriage runs to the back;
start the process
Sewing folding station in
Check/adjust fastening of the folding station
9003 Wrong needle position before sewing start Turn manually the hand wheel in lever up position
ref Request to carry out the reference run after switching the machine on. Step back on the pedal
Current
seam length
fl ashes
Corner knife at the seam beginning cannot be reached Change the present seam length, or change the loading
position, or change L1 (adjust distance counter knife).
Quick Reference Card 745-35S
© Dürkopp Adler AG 0791 745400 EN - 01.0 - 04/2016
Switch on
P
Sewing mode
Editing the current seam parameters
100 Seam length mm
101 Stacker on/off
102 Center knife on/off
103 Center knife correction seam beginning 1/10 mm
104 Center knife correction seam end 1/10 mm
105 Corner knife on/off
106 Corner knife correction seam beginning 1/10 mm
107 Corner knife correction seam end 1/10mm
108 Stitch length 1/10 mm
109 Sewing motor speed
110 Sewing motor soft start on/off
111 Sewing motor number of soft start stitches
112 Sewing motor soft start speed
113 Clamping mode
0 = Lower left and right feeding clamp simultaneously
1 = Lower left feeding clamp fi rst
2 = Lower right feeding clamp fi rst
114 Positioning point
0 = front
1 = center
2 = rear
115 Positioning point offset mm
116 Type seam tightening seam beginning
0 = Bartack
1 = Condensed stitches
117 Number of condensed stitches seam beginning
118 Stitch length condensed stitches/Bartack Seam beginning 1/10 mm
119 Number of bartacks seam beginning
120 Type seam tightening seam end
0 = Bartack
1 = Condensed stitches
121 Number of condensed stitches seam end
122 Stitch length condensed stitches/Bartack Seam end 1/10 mm
123 Number of bartacks seam end
124 Material feed type,
0 = Material runs to the loading position
1 = Material runs to the stacking position
2 = no run, in stacking position,
125 Type of waiting position
0 = Feeding clamp runs to the waiting position
1 = Feeding clamp remains in stacking position
126 Material feed to the stacking position
Quick Reference Card 745-35S
© Dürkopp Adler AG 0791 745400 EN - 01.0 - 04/2016
127 Loading speed
128 Return speed
129 Downholder on/off
130 Sewing mode
0 = Constant sewing length
1 = Light-barrier for fl ap scanning
131 Light-barrier correction seam beginning 1/10 mm
132 Light-barrier correction seam end 1/10 mm
133 Material feed to the waiting position
134 Max. Flap length
135 Flap clamp on/off
136 Pedal mode
0 = normal
1 = Pedal has to be in basic position before the next step
2 = Pedal actuation for moving in sewing position (fl ap clamp)
137 Second light barrier active
0 = 1st light barrier active
1 = 2nd light barrier active
Switch on
P
Sewing mode
Editing the current seam parameters
Tabla de contenidos
Otros manuales de Máquina de coser de DURKOPP ADLER
DURKOPP ADLER
DURKOPP ADLER 4182i-1 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 745-34-1 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 370 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER DAC BASIC - CLASS 271 PART II V 12-2010 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 1265-5 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 967 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 550-8-3 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 805 Guía
DURKOPP ADLER
DURKOPP ADLER 867 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 745-34-2 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 272-160362 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 531-211 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 878-M PREMIUM Instrucciones de funcionamiento
DURKOPP ADLER
DURKOPP ADLER 171 Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 867-M Premium Manual de funcionamiento original
DURKOPP ADLER
DURKOPP ADLER 745-34 - Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 767 - Manual de usuario
DURKOPP ADLER
DURKOPP ADLER M-Type Premium Series Manual de funcionamiento
DURKOPP ADLER
DURKOPP ADLER 580 - Manual de usuario
DURKOPP ADLER
DURKOPP ADLER 745-35-10 B Manual de usuario
