Duplo DC-535 Manual de usuario

¡Store in a manner that permits use anytime.

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

For the safe usage of the machine, correct operation and

periodic maintenance are essential. Read this manual

before using the machine.

WARNING

DC-535 Cutter

Ver.1

- 1 -

Introduction

Thank you for purchasing the DC-535 Cutter.

This product is the result of our many years of experience in the field of office

equipment.

Be sure to read this manual before using the machine.

In order to use the machine safely and efficiently, read this manual thoroughly, and make

sure that you understand all of the instructions that it gives, so that you operate the

machine correctly.

Take good care of this manual. Keep it in a safe place where it can be consulted at any

time.

Symbols and pictures

Safety instructions

In this manual and on the stickers affixed to the machine, a variety of symbols and

pictures are used. These symbols and pictures provide warnings and instructions to

prevent danger to you or other people and damage to office property. The meanings

Indicates potential danger of death or serious injury if it is ignored.

Indicates potential danger of injury or damage to property if it is ignored.

Warning :

Caution :

Examples of pictorial symbols

Other nomenclature

A triangle indicates danger. The precise nature of the danger is indicated by a

pictorial symbol inside the triangle. The symbol shown here indicates danger of

electric shock.

A circle with a line diagonally across it indicates prohibition. The particular act

prohibited is indicated by a picture inside the circle. The symbol shown here indicates

a prohibition of disassembly.

A black disc indicates an instruction, or sometimes prohibition. The content is

indicated by pictorial symbols drawn in white in the disc. The symbol shown here

indicates an instruction to pull the plug out of the outlet.

IMPORTANT :

NOTE :

Introduces instructions for correct operation and maintenance of the

machine. A failure to follow them may cause insufficient performance or

breakdown.

Introduces useful information for the operation and maintenance of the

machine as well as information on the performance, etc. of the product.

PLEASE NOTE

In the interest of upgrading our products, specifications and other data given in this

manual are subject to change without notice. If the manual contains anything that

you do not understand, contact the manufacturer for clarification.

- 2 -

TABLE OF CONTENTS

Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.Names and functions of each part. . . . . . . . . . . . . . . . . . 7

Feed side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Ejection side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.Names and function of the operation panel. . . . . . . . . . 9

Display unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operation unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3. Procedures for using the machine . . . . . . . . . . . . . . . . 10

4. Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

¡ About modes and mode displays . . . . . . . . . . . . . . . . . . . . . . . . . 15

1. Turning on the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2. Selecting the cutting dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3. Performing test operation

to check the cutting dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4. Starting operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5. Registering cutting dimensions . . . . . . . . . . . . . . . . . . 19

1. Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2. Procedure for registering cutting dimensions . . . . . . . . . . . . . . . . . 19

6. Other functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

¡Deleting registered data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

¡ To temporarily offset the cutting position . . . . . . . . . . . . . . . . . . . 21

7. Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

<<Message displayed on LCD when a jam occurs>> . . . . . . . . . . . . 22

<<Corrective action for paper jams>> . . . . . . . . . . . . . . . . . . . . . . . . 23

¡Removing jammed paper from the feed unit . . . . . . . . . . . . . . . . . 23

¡Removing jammed paper from the cutter

or ejection unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

8. Specifications and accessories . . . . . . . . . . . . . . . . . . 25

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

- 3 -

Safety instructions

¡Be sure to follow these instructions. They are extremely important for safety.

WARNING

¡Do not modify the machine. Do not remove any of the covers from the machine.

¡Do not insert pins, wire or other foreign objects into the machine. Do not allow

any liquid to get into the machine through its openings or gaps in its structure.

Liquid inside the machine may result not only in breakdown, but also in electric

shock or fire.

¡Keep your hands off inside the margin trimmer. It contains cutting edges which

may hurt you.

¡Do not put your hands or fingers inside the front or rear safety cover during

operation, or they could be crushed or otherwise injured.

¡Use tweezers or a similar tool to remove jammed paper. Before removing

jammed paper, be sure to pull the power supply plug out from its outlet in order

to prevent electric shock.

To avoid electric shock:

To avoid injury to hands or fingers:

¡Do not use supply voltage other than the specified voltage.

Doing so may result in fire or electric shock.

¡Always pull the power supply plug out of its outlet before removing jammed

paper.

Do not insert or remove the plug with wet hands.

- 4 -

CAUTION

Installation location

General operation instructions

¡Install the machine in a level place.

¡Do not install the machine in a place subject

to direct sunlight or near heating equipment.

¡Do not install the machine in a place subject

to extreme temperatures (high or low), or in a

place subject to heavy vibration.

¡Avoid installing the machine in a place with

high humidity, or with large amount of oil,

iron filings, or dust.

¡Do not connect the cutter to a power outlet

that is also used for equipment that

generates noise, such as large-size office

equipment or refrigerators.

¡Do not use the cutter to cut paper that

exceeds the specification paper thickness.

Doing so could result in breakdown.

¡Do not attempt to cut paper with staples,

paper clips or any other pieces of metal

attached to it.

¡Use a dry cloth to remove paper cuttings

collected in the machine and to clean the

rubber rollers or other parts. Be sure to pull

the power supply plug out from its outlet

before cleaning.

Safety instructions

- 5 -

Safety instructions

DLocations of warning stickers

The locations of the machine's warning stickers are shown below. To ensure safe work, read the stickers and

heed their instructions. Keep the stickers clean at all times. If they become damaged or peel off, replace them

with new ones.

- 6 -

No. Part No. Name Q'ty

L8-T1080

L8-T1070

L8-T1100

Warning Sticker 1

Warning Sticker 2

Warning Sticker 3

Safety instructions

- 7 -

1. Names and functions of each part

Feed side

No. Name Function

qFront safety cover Open this cover to adjust the paper thickness or to remove jammed paper.

wOperation panel See "Names and functions of the operation panel" on p. 9.

ePaper tray Load the paper into these trays.

rAuxiliary paper tray

tPaper stopper Guides the trailing edge of the paper.

yGuide Hold the trailing edge of the paper.

uPower switch Press the [ ] side of the switch to turn the power on, and the [ ] side to

turn it off.

iInlet The power cord (an accessory) is inserted into this.

oPaper guides Set the position of these guides to match the width of the paper.

!0 Lock lever Pull this lever backward (toward you) to lock the paper guides.

qoe w

- 8 -

1. Names and functions of each part

Ejection side

No. Name Function

!1 Rear safety cover Open this cover to adjust the margin slitters or to remove jammed paper.

!2 Ejection tray Receives ejected paper.

!3 Ejection stopper Stops the leading edge of ejected paper sheets.

!4 Ejection guides Laterally positions the ejected paper.

!5 Knob Moves the margin slitter. Turn clockwise to lock.

!6 Pointers Indicate the margin cutting position.

!7 Scale Measures the paper dimensions for cutting.

!8 Aligner Moves the left and right margin slitters simultaneously.

!9 Trash box Cut-off margins are deposited into this box.

!6 !1

- 9 -

Names and function of the operation panel

No. Name Function

Liquid crystal Display

Displays various messages.

wCOVER indicator Lights when a safety cover is open.

eJAM indicator Lights when a paper jam occurs.

rPAPER indicator Lights when there is no paper in the paper tray.

tREADY TO RUN

indicator In the RUN mode, lights to indicate the machine is ready to run.

yPOWER indicator Lights when the power is on.

No. Name Function

qF button Function button - used in conjunction with other buttons to execute functions

such as cutting dimension registration.

wMODE button Switches among the LCD's display modes.

eSET button In the RUN mode, pressing this button executes test cutting.

In the SET mode, pressing this button memorizes cutting dimensions.

r3button When the machine is stopped in the RUN mode, or due to a jam, pressing

the + button will move the paper forward, and pressing the - button will

move it backward.

t4button

yRESET button

A multifunction button that when pressed at the same time the STOP button

is pressed,the number of sheets fed and cut will be reset.

If pressed for three or more seconds in the Freesize Input Mode, the current

registered data will be erased.

uSTART button In the RUN mode, pressing this button starts cutting operation (except when

a paper jam has stopped operation).

iSTOP button Press this button to stop the machine. Also press this button to restart the

machine after it has been stopped by a paper jam (but note that you must

first eliminate the cause of the jam before the machine can be restarted).

Display unit qw t yer

tewq y u i

Operation unit

Tabla de contenidos

Otros manuales de Cortador de Duplo

Duplo

Duplo DocuCutter CC-228 Instrucciones de construcción

Duplo

Duplo DC-646 Manual de usuario

Duplo

Duplo DC-618 Manual de usuario

Duplo

Duplo DocuCutter DC-545 Guía de instalación

Duplo

Duplo DocuCutter CC-229 Instrucciones de construcción

Duplo

Duplo DocuCutter CC-229 Guía de inicio rápido

Duplo

Duplo DocuCutter DPC-400 Manual de usuario

Duplo

Duplo DC-618 Manual de usuario

Duplo

Duplo DocuCutter DC-545HC Manual de usuario

Duplo

Duplo DocuCutter CC-330 Guía de inicio rápido

Duplo

Duplo DC-646 Manual de usuario

Duplo

Duplo DocuCutter CC-330 Instrucciones de construcción

Manuales populares de Cortador de otras marcas

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manual de usuario

Makita

Makita DCS552 Manual de usuario

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manual de usuario

Makita

Makita 4112HS Manual de usuario

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manual de usuario

Hitachi

Hitachi CM 4SB2 Guía de solución de problemas

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manual de usuario

GCC Technologies

GCC Technologies AFJ-24S Manual de usuario

DeWalt

DeWalt XR LI-ION DCS350N Manual de usuario

Baudat

Baudat ES1 Manual de usuario

Mafell

Mafell ZAF 200 Guía

Makita

Makita 4100NH Manual de usuario

Formax

Formax FD 574 Manual de usuario

EINHELL

EINHELL TE-MA 1500 Manual de usuario

Husqvarna

Husqvarna Cut-n-Break K 760 Manual de usuario

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manual de usuario

TRI tool

TRI tool 301A Manual de usuario

Roller

Roller King 1 1/4 Manual de usuario