DSC SEA-B-QUE Manual de usuario

○

1○

2○

3○

4○

5○

6○

7○

8○

9○

1. DC+12V IN: Power input DC+12V/1.5A.

2. DC+12V OUT: DC+12V/750mA for camera only, and with an over current protector.

(Note: If you don’t use this port for cameras, you can use the DC+12V/500mA adaptor.)

3. ALARM IN: Once triggered, the built-in buzzer rings on for a 20-sec time. This port could be connected to

alarm sensor, e.g.: PIR Detector, Magnetic Reed Switch Detector.

4. AUDIO IN: RCA female for input audio signal.

5. VIDEO IN: BNC female for input video signal.

6. POWER/State LED: Indicated to power on and ARM status.

7. DISARM: Alarm ON / OFF selection.

8. CH SELECT (A B C D): 5.8GHz transmission channel selection.

9. ID AND ALARM MUTE: ID address setting is use for paring with receivers (RX unit). It must be make the

same code setting to link transmitter and receiver each other. The alarm mute function is use for muting built

-in buzzer at TX unit.

10. ANT: RP-SMA connector for connected to 5.8 GHz antenna.

*REMARK: When the frequency channels have the interference, adjust antenna or change the channel of transmitter

and don’t close to 802.11 a/b/g AP router and other 5.8GHz devices. (Note: Please keep 3 ~ 5 meter away)

* Panel View: TX unit

Bit 1 Bit 2 Bit 3 ID Address

(Pairing with RX)

Bit 4 Alarm Mute

00000ON

00111OFF

0102

0113

1004

1015

1106

1117

(1 = SW ON, 0 = SW OFF)

11/5/2009

Indications Power/State LED

Power On On

ARM High speed Flashing

MODEL:DSC-5800VHK( :SK2-5800A)

○

1○

2○

3○

4○

5○

6○

7○

8○

1. DC+12V IN: Power input DC+12V/500mA.

2. ALARM OUT: Once triggered, the built-in buzzer and alarm remains on for a 20-sec time. This port could

be connected to alarm devices, e.g.: Siren, Flashing Unit.

3. AUDIO OUT: RCA female for audio signal output.

4. VIDEO OUT: BNC female for video signal output.

5. POWER/STATE LED: Indicated to power on or ARM and RF link status.

6. DISARM: Alarm ON / OFF selection.

7. CH SELECT (A B C D): 5.8GHz transmission channel selection.

8. ID AND ALARM MUTE: ID address setting is use for paring with transmitters (TX unit).

It must be make the same code setting to link transmitter and receiver each other. The alarm mute function

is use for muting built-in buzzer and disables the alarm output at RX unit.

9. ANT: RP-SMA connector for connected to 5.8 GHz antenna and built-in 3.3V / 25mA bias-tee circuit for an

active antenna.

*REMARK: When the frequency channels have the interference, adjust antenna or change the channel of transmitter

and don’t close to 802.11 a/b/g AP router and other 5.8GHz devices. (Note: Please keep 3 ~ 5 meter away)

* Panel View: RX unit

Bit 1 Bit 2 Bit 3 ID Address

(Pairing with TX)

Bit 4 Alarm Mute

00000ON

00111OFF

0102

0113

1004

1015

1106

1117

(1 = SW ON, 0 = SW OFF)

11/5/2009

Indications Power/State LED

Power On On

ARM High speed Flashing

RF Loss/Waiting TX Link Low speed Flashing

MODEL:DSC-5800VHK( :SK2-5800A)

5.8GH TX (Transmitter) ×1 5.8GH RX (Receivers) x1

Antenna ×2 User manual ×1

Screws x 4 ×2 Plastic-Conical-Anchor x 4 ×2

Power Adaptor (DC 12V/1.5A) ×1 Power Adaptor (DC 12V/500mA) x1

* Packing List:

Model No. TX RX

CHANNAL CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

FREQUENCY 5740

MHz

5752

MHz

5771

MHz

5790

MHz

5809

MHz

5828

MHz

5847

MHz

5760

MHz

RF IMPEDANCE 50 ΩTypical

5.8G BIAS-TEE 3.3V/25mA

MINIMUM RECEIVER SENSITIVITY -84dBm

POWER SUPPLY DC12V/1.5A Adaptor DC12V/500mA Adaptor

CURRENT CONSUMPTION 350mA 280mA Max.

DC OUTPUT DC12V/750mA

RF OUTPUT POWER 500mW

VIDE INPUT / VIDEO OUTPUT 1.0 Vp-p Composite @ 75Ω

AUDIO INPUT / VIDEO OUTPUT 2.0 Vp-p Typical, 3.0 Vp-p Max. @ 600Ω

ALARM INPUT TTL/CMOS (Level Detection)

ALARM OUTPUT NC/NO/COM (Dry Contact) Contact

Rating: AC 125V / 0.5A ; DC 24V / 1A

OPERATION TEMPERATURE 14° F ~ 122° F (-10°C ~ 50°C)

WEIGHT 5.8 Oz ( 164 g)

DIMENSIONS W x H x D: 110 x 30 x 88 mm (without Antenna)

* Specification :

11/5/2009

*** All Specifications are subject to change without notice.

1. Be careful, never let any water in this equipment.

2. If necessary, use a soft cloth moistened with alcohol to wipe off the dust.

3. Be extra careful not to shake the unit.

4. Avoid places where temperatures exceed 122° F (50°C)or higher.

5. Avoid places where there are frequent vibrations or shocks.

6. When any abnormalities occur, make sure to unplug the unit and contact your local dealer.

* Caution for Installation:

MODEL:DSC-5800VHK( :SK2-5800A)

FCC Part 15 Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pur-

suant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can ra-

diate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20

centimeters between the radiator and your body.

3. Any changes or modifications (including the antennas) made to this device that are not ex-

pressly approved by the manufacturer may void the user’s authority to operate the equip-

ment.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de seguridad de DSC

DSC

DSC PC1616; PC1832; PC1864 Manual de usuario

DSC

DSC PC-1616 - REV2 Manual de usuario

DSC

DSC Power632 Manual de usuario

DSC

DSC Power608 Manual de usuario

DSC

DSC PC 4010 Manual de usuario

DSC

DSC PC5008 Manual de usuario

DSC

DSC LCD5501Z32-433 NA Manual de usuario

DSC

DSC PC2525 Manual de usuario

DSC

DSC PC155O Manual de usuario

DSC

DSC WT5500 Manual de usuario

DSC

DSC PowerSeries Neo HS2TCHP Manual de usuario

DSC

DSC PTD1610-SCW Manual de operación y mantenimiento

DSC

DSC Power8 PC5005 Manual de usuario

DSC

DSC PC2550 Manual de usuario

DSC

DSC Escort5580 Voice Assisted Security Control Manual de usuario

DSC

DSC Maxsys PC6010 Manual de usuario

DSC

DSC MAXSYS PC4020 Manual de usuario

DSC

DSC PowerSeries PC1404 Manual de usuario

DSC

DSC Impassa PT4 Manual de usuario

DSC

DSC PC 5010 Manual de usuario

DSC

DSC PC1550 Manual de usuario

DSC

DSC PC4020 - 2 Manual de usuario

DSC

DSC iOtega Manual de usuario

DSC

DSC Envoy NT9010 Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario