Dreamline ENIGMA Manual de usuario

Rev 2.1

ENIGMA Shower Door Installation Instruction

IMPORTANT

Please read carefully the following instructions before installing your shower door. If you have any

questions regarding shower door installation, please call our technical support specialists Monday

through Friday, 9:00AM –5:00PM EST at 1-866-731-8378 ext. 3 or e-mail our technical support

group at support@BathAuthority.com

DreamLineTM reserves the right to alter, modify or redesign products

at any time without prior notice. For the latest up-to-date technical

drawings, manuals or any other details please refer to the

BathAuthority.com web page.

Attention: This door is extremely heavy and requires

professional installation.

Rev 2.1

Preparation

1. After opening all boxes and packages, read this introduction carefully. Check that all of the

needed parts are included in the package, by marking all the components on the “Detailed

Diagram of Shower Door Components”. Examine boxes and packages for shipping damage. If the

unit has been damaged, has a finishing defect, or has missing parts, please contact our customer

support department within 3 business days of the delivery date. Please note that DreamLine TM

will not replace any damaged products or missing parts free of charge after 3 business days

or if the product has been installed. Feel free to contact DreamLineTM if you have any questions.

2. If this unit is going to be installed in a new construction, please, install all of the required

plumbing and drainage before installing the shower. Use a competent and licensed (if required

by local code) plumber for all plumbing installation

3. Please note that you should consult your local building codes on questions on installation

compliance standards. Building and plumbing codes vary by location, and DreamLine is not

responsible for code compliance standards for your project.

4. Please insure that prior to the installation the tub is leveled and solid and will be able to support

the total weight of the unit. Also make sure the walls are at right angles. While some adjustment

in leveling of the door is possible, irregular tub level or improper angle of side walls will result in

serious problems for your installation. Please, note that some adjustments and drilling might be

necessary during the installation process.

5. This unit has to be installed against a finished floor and walls.

6. Please, NOTE! This door does not have out-of-plumb adjustment. Make sure your walls are

at right angles.

7. This door requires 31/2" wide threshold or installation space.

8. Please note that Step 7 calls for installation of the door to the wall using anchors. However,

the manufacturer strongly recommends installing these heavy doors to the studs or to

preinstalled 2x6 wood reinforcement behind the wall and attaching the Wall brackets to it.

Tools Required

Caulk Tape

Measure Pencil Screwdriver

Phillips (Ø=5/16")

Drill bit

Level Gun

Caulk Drill

Electric Hammer

(Ø=3/8")

Drill bit

Miter saw or Hacksaw

Detailed Diagram of the Shower Door Components

Rev 2.1

17 18

Packing List

Door Stopper

2pcs

Round head screw ST6×45

2pcs

Stationary glass

1pc

Hex wrench 3mm, 4mm, 5mm

1set

Guide rail

1pc

Guide block

1pc

Roller

4pcs

Bumper strip

1pc

Glass door

1pc

Threshold cover

1pc

Handle

1pc

Threshold

1pc

Glass bracket

2pcs

Countersunk screw ST4.2×30

6pcs

Guide rail bracket

2pcs

Anti-water strip

2pcs

Large anchor Ø 3/8″

2pcs

Small anchor Ø 5/16″

6pcs

NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed

diagram and packing list in your manual as a reference. Before discarding the carton, check for small

hardware bags that tend to fall to the bottom of the box. If any parts are damaged or missing, please

contact DreamLineTM for replacement.

Rev 2.1

Shower Door Installation

1. Measure the distance between two finished

walls.

This distance is marked as “W”.

See Fig. 1 for details.

Fig. 1

2. Your Guide rail (03) has been precut for the

installation between the walls with a distance of

60”.

If W=60”, then it is unnecessary to cut the

Guide rail and you can continue to Step#3.

If W<60”,then you will need to cut the Guide

rail from the end which is farthest from the

Glass bracket (07) holes.

The length to cut off will be “L”:

L = (60”−W).

See Fig. 2 for details.

Fig. 2

3. Your Threshold (15) has been precut for

the installation between the walls with a

distance of 60”.

If W=60”, then it is not necessary to cut the

threshold.

Rev 2.1

If W<60”, then you have to cut the Threshold to the size of “W”.

The length to cut off will be D1

D1 = (D−W).

See Fig. 3 for details.

Fig. 3

4. Place the Threshold (15) into the designated

position and mark the drilling holes on the floor.

Remove the Threshold, drill the holes in the

floor using Ø5/16”drill bit and insert Small

anchors Ø5/16”(18).

Apply silicone on the bottom of the Threshold

around the holes, place it back to the designated

position and fasten it to the floor with the

Countersunk screws ST4.2×30 (16).

See Fig. 4 for details.

Fig. 4

5. Install the Guide rail (03) onto the

Stationary glass (02) with the Glass

brackets (07) and tighten the screws.

Slide the Door stoppers (01) on each

end of the Guide rail and secure them

temporarily.

Slide the Guide Rail brackets (08) on

each end of the Guide rail and

temporarily secure them as well.

See Fig. 5 and Fig. 6 for details.

Rev 2.1

Fig. 5

NOTE:

Before you install the Stationary glass (02), you

have to take the Glass door (05) into the shower

room and lean it against the wall.

Fig. 6

6. Place the Stationary glass (02) on the

threshold and push the bottom edge into the

groove of the Threshold (15) as shown on

Fig. 7 and Fig. 8.1.

Butt up the Stationary glass against the wall.

(Please note that the Guide rail (03)

secured on the Stationary Glass should

face inside the shower).

Make sure the Stationary glass and the

Guide rail are leveled. If a horizontal

adjustment is required, adjust it in the Glass

brackets (07).

See Fig. 7 for details.

Fig. 7

Rev 2.1

7. Outline the Guide rail brackets (08) position.

Put the Stationary glass (02) aside.

Remove the Guide Rail Brackets from the Guide

Rail, place them to the outlined positions on the wall

and mark the drilling holes. Drill the holes using Ø

3/8” drill bit.

Insert the Large anchors Ø3/8″(9) and mount the

male part of the Guide rail brackets onto the wall

using the Round head screws ST6×45 (10).

See fig. 8 for details.

Fig. 8

8. Apply a small amount of silicone into the Threshold

(15) channel.

Place the Stationary glass (02) back into position and attach

both female parts of the Guide rail brackets (08) to their male

parts on the walls.

Tighten the set screws on the Guide rail brackets to secure the

Guide rail (03) between two walls.

See Fig. 9 and Fig. 10 for details.

Fig. 9

Rev 2.1

Fig. 10

9. Place the Guide block (12) on the floor

and parallel it to the Stationary glass (02).

It should not pass beyond the vertical

edge of the glass.

Take a measurement to ensure the

distance between the front line of the

glass and the center line of the Guide

block is 2 3/16”.

Hold it firmly and mark the drilling hole

on the floor. Remove the Guide block,

drill the hole using Ø5/16”drill bit; insert

the Small anchor Ø5/16” in and then

secure the Guide block to the floor with

the Countersunk screw ST4.2×30 (16).

See Fig. 11 for details.

Fig. 11

10. Attach two top Rollers (04) to the

Glass door (05).

Suspend the door by hanging the

Rollers onto the Guide rail (03) and

slide the bottom edge of the Glass

door into the groove of the Guide

block (12).

Then mount two lower Rollers (04)

onto the door to secure the door to the

Guide rail.

See Fig. 12 for details.

2 4

Rev 2.1

Fig. 12

11. Adjust the fasteners on both top Rollers (04) to ensure that the

bottom edge of the Glass door (05) does not touch the bottom of

the guide block. Tighten the fasteners.

See Fig. 13 for details.

Fig. 13

12. Refer to Step 3 to cut the Threshold

cover (14) if it’s necessary.

Push the Threshold cover into the

Threshold (15) groove when the door is

in the opened position.

Install the Handle (06) to the Glass

door (05).

See Fig. 14 for details.

Fig. 14

Rev 2.1

13. Press the Bumper strip (13) on the vertical edge of the sliding

Glass door (05) that’s close to the handle and also press the

Anti-water strip (17) on the vertical edges of the Stationary

glass (02) and the other side of the Glass door.

See Fig. 15 for details.

Fig. 15

14. Adjust both Door Stoppers (01) to ensure that they are positioned

upright and the door is in its maximum opening and closing range.

Tighten the set screw to fasten them in place.

See Fig. 16 for details.

Fig. 16

15. Apply silicone along the connection of

Stationary glass and the wall. You may

also apply additional layer of silicone

along the Threshold (optional)

See fig. 17 for details.

Otros manuales para ENIGMA

Tabla de contenidos

Otros manuales de Accesorio de baño de Dreamline

Dreamline

Dreamline PYRAMID Manual de usuario

Dreamline

Dreamline Aquaswing-EX Manual de usuario

Dreamline

Dreamline FLEX Shower Enclosure Manual de usuario

Dreamline

Dreamline Butterfly Shower Door & Base Kit Manual de usuario

Dreamline

Dreamline TORERO Manual de usuario

Dreamline

Dreamline BUTTERFLY Manual de usuario

Dreamline

Dreamline SHCM-2718-00 Manual de usuario

Dreamline

Dreamline SHCM-2648-00 Manual de usuario

Dreamline

Dreamline ENIGMA 60" wide Manual de usuario

Dreamline

Dreamline UNIDOOR Manual de usuario

Dreamline

Dreamline SHCM-3031-00/01 Manual de usuario

Dreamline

Dreamline ENCORE-X SHDR-166062X Series Manual de usuario

Dreamline

Dreamline UNIDOOR-X L1 Series Manual de usuario

Dreamline

Dreamline QWALL-3 Manual de usuario

Dreamline

Dreamline AQUALUX SHDR-3348588 Series Manual de usuario

Dreamline

Dreamline FRENCH LINEA Series Manual de usuario

Dreamline

Dreamline ALLIANCE PRO BG SDAB60A700 Manual de usuario

Dreamline

Dreamline Visions Manual de usuario

Dreamline

Dreamline AQUA-Q FOLD SD-363072Q Series Manual de usuario

Dreamline

Dreamline Unidoor Lux D SHDR -23297210 Series Manual de usuario

Dreamline

Dreamline SHST-01-PL Manual de usuario

Dreamline

Dreamline PRISM PLUS Manual de usuario

Dreamline

Dreamline SHDR-4125720 Series Manual de usuario

Dreamline

Dreamline PRISM PLUS SHEN-2634340 Series Manual de usuario

Manuales populares de Accesorio de baño de otras marcas

DURAVIT

DURAVIT C.1 C15240 0090 Manual

Heatstore

Heatstore HSTRL500WTN Manual de usuario

Sunshower

Sunshower PURE SOLO Manual de usuario

Delabie

Delabie Delabie Sporting 714700 Manual de usuario

Kohler

Kohler K-13056 Instrucciones de montaje

ESS

ESS Container TCL-11 Manual de usuario

Mustee

Mustee 22C Manual de usuario

VITRA

VITRA V-Flow Manual de usuario

baliv

baliv DUK-80.30 T Manual de usuario

Malmet

Malmet B105BT Manual de usuario

bathstore

bathstore Transition H1690MM Guía

BELLOSTA

BELLOSTA Edward 0800/M Manual de usuario

baliv

baliv DU-5160 Manual de usuario

Franke

Franke PRTR0006 Manual de usuario

Gessi

Gessi RILIEVO 59011 Manual de usuario

noken

noken VITAE 100188525-N299998810 Manual de usuario

Allen + Roth

Allen + Roth 1142VA-30-201 Manual de usuario

Britex

Britex HBDA Manual de usuario