Dometic Enerdrive EN43510 Manual de usuario
Owner’s Manual
Rev: 1.0 (2021)
EN43510 - MPPT Solar Controller 12/24V - 10Amp
EN43520 - MPPT Solar Controller 12/24V - 20Amp
EN43530 - MPPT Solar Controller 12/24V - 30Amp
EN43540 - MPPT Solar Controller 12/24V - 40Amp
Please Keep This Manual For Future Reference
For safe and optimum performance, the MPPT Solar Controller must be used properly.
Carefully read and follow all instructions and guidelines in this manual and give special attention to the
CAUTION and WARNING statements.
While every precaution has been taken to ensure the accuracy of the contents of this guide, Enerdrive
assumes no responsibility for errors or omissions. Note as well that specications and product functionality
may change without notice.
Please be sure to read and save the entire manual before using your MPPT Solar Controller .
Misuse may result in damage to the unit and/or cause harm or serious injury. Read manual in its
entirety before using the unit and save manual for future reference.
MPPT Solar Controller Owners Manual Rev. 1.0. This Manual is applicable to all units with serial number
prex EN.
Disclaimer
Important
Product Numbers - Battery Charger Series
EN43510 MPPT Solar Controller 12/24V-10Amp
EN43520 MPPT Solar Controller 12/24V-20Amp
EN43530 MPPT Solar Controller 12/24V-30Amp
EN43540 MPPT Solar Controller 12/24V-40Amp
Service Contact Information
Dometic Power & Control (Enerdrive) Pty Ltd
PO Box 9159, Wynnum Plaza, QLD 4178
Ph: 1300851 535 / Fax: 073390 6911
Email: support@enerdrive.com.au | Web: www.enerdrive.com.au
MPPT Solar Controller Owners Manual Rev. 1.0.Page 2
Enerdrive MPPT Solar Controller owner’s manual © 2021 Dometic Power & Control (Enerdrive) Pty Ltd.
All rights reserved. No part of this document may be reproduced in any form or disclosed to third parties
without the express written permission of Dometic Power & Control (Enerdrive) Pty Ltd. Enerdrive
reserves the right to revise this document and to periodically make changes to the content hereof without
obligation or organisation of such revisions or changes, unless required to do so by prior arrangement.
1. Unless specically agreed to in writing, Dometic Power & Control (Enerdrive) Pty Ltd: makes no
warranty as to the accuracy, suciency or suitability of any technical or other information
provided in its manuals or other documentation.
2. Assumes no responsibility or liability for losses, damages, costs or expenses, whether
special, direct, indirect, consequential or incidental, which might arise out of the use of such
information. The use of any such information will be entirely at the user’s risk.
3. Reminds you that if this manual is in any language other than English although steps have
been taken to maintain the accuracy ofthe translation, the accuracy cannot be guaranteed.
4. Makes no warranty, either expressed or implied, including but not limited to any implied
warranties of merchantability or tness for a particular purpose, regarding these Enerdrive
products and makes such Enerdrive products available solely on an “as is” basis.
5. Shall in no event be liable to anyone for special, collateral, incidental, or consequential
damages in connection with or arising out of purchase or use of these Enerdrive products.The
sole and exclusive liability to Enerdrive, regardless of the form of action, shall not exceed the
purchase price of the Enerdrive products described here in.
Notice of Copyright
Exclusions For Documentation And Product Usage
www.enerdrive.com.au Page 3
Page 4
Table of Contents
2. INSTALLATION
1.1 OVERVIEW
2.1 CAUTION
1.2 CHARACTERISTICS
2.2 PV ARRAY REQUIREMENTS
MPPT Solar Controller Owners Manual Rev. 1.0.
1. GENERAL INFORMATION
3. DISPLAY
4. PARAMETERS SETTING
5. OTHERS
6. TECHNICAL SPECIFICATIONS
APPENDIX | CONVERSION EFFICIENCY CURVES
3.1 OVERVIEW
4.1 BATTERY PARAMETERS
4.1.1 SUPPORTED BATTERY TYPES
4.1.2 SETTINGS
4.2 LOAD WORKING MODES
5.1 PROTECTION
5.2 TROUBLESHOOTING
5.3 MAINTENANCE
3.2 OPERATION
2.3 WIRE SIZE
2.4 MOUNTING
5
5
6
7
7
8
10
12
15
15
17
20
20
20
20
22
23
23
25
27
28
29
The Enerdrive MPPT Solar Controllers adopt the advanced MPPT control algorithm, it can minimize the
maximum power point loss rate and loss time, quickly track the maximum power point (MPP) of the PV
array and obtain the maximum energy from solar array under any conditions; and it can increase the ratio
of energy utilization in the solar system by 20%-30% compared with PWM charging method.
IP33 Ingress protection and isolated RS485 design further improve the controller’s reliability and meet
the dierent application requirements.
Enerdrive MPPT Solar Controllers has self-adaptive three-stage charging mode based on digital control
circuit, which can eectively prolong the lifespan of batteries and signicantly improve the system
performance. It also has comprehensive electronic protection for overcharge, over discharge, PV & battery
reverse polarity. This controller can be widely used for RV, Marine, remote o grid monitoring and many
other applications.
• CE certication(LVD EN/IEC62109,EMC EN61000-6-1/3)
• LCD display
• Advanced MPPT technology & ultra-fast tracking speed guarantee tracking eciency up to 99.5%
• Maximum DC/DC transfer eciency is as high as 98.6%.
• Advanced MPPT control algorithm to minimize the MPP lost rate and lost time
• Accurate recognition and tracking of multi-peaks maximum power point
• Wide MPP operating voltage range
• Support lead-acid and lithium batteries; voltage parameters can be set on the controller
• Programmable temperature compensation
• Limit charging power & current over rated value
• Real-time energy statistics function
• Power reduction automatically over temperature value
• Multiple load work modes
• Comprehensive electronic protection
• Isolated RS485 with 5V/200mA protected output for no power devices, with Modbus protocol
• IP33 Ingress protection
For the BCV, FCV, LVD, and LVR, users can modify them on the local controller when the battery type is "USE."
www.enerdrive.com.au Page 5
1. GENERAL INFORMATION
1.1 OVERVIEW
FEATURES
1.2 CHARACTERISTICS
Page 6 MPPT Solar Controller Owners Manual Rev. 1.0.
1
2
3
4
5
1 2 3 45
Figure 1 - Product Characteristics
RTS* Port
*If the temperature sensor is short circuited or damaged, the controller will charge
discharge according to the voltage setting point at the default temperature
setting of 25°C (no temperature condensation).
RS485 Communication Port
PV Terminals
Battery Terminals
Load Terminals
www.enerdrive.com.au Page 7
2. INSTALLATION
2.1 CAUTION
• Please read the entire installation instructions to get familiar with the installation steps before
installation.
• Be very careful when installing the batteries, especially ooded lead-acid battery. Please wear
eye protection and have fresh water available to wash and clean any contact with battery acid.
• Keep the battery away from any metal objects, which may cause short circuit of the battery.
• Explosive battery gases may come out from the battery during charging, so make sure ventilation
condition is good.
• Ventilation is highly recommended if mounted in an enclosure. Never install the controller in a
sealed enclosure with ooded batteries! Battery fumes from vented batteries will corrode and
destroy the controller circuits.
• Loose power connections and corroded wires may result in high heat that can melt wire insulation,
burn surrounding materials, or even cause re. Ensure tight connections and use cable clamps to
secure cables and prevent them from swaying in mobile applications.
• The controller can work with lead-acid battery and lithium battery within its specications.
• Battery connection may be wired to one battery or a bank of batteries. The following instructions
refer to a singular battery, but it is implied that the battery connection can be made to either one
battery or a group of batteries in a battery bank.
• Multiple same models of controllers can be installed in parallel on the same battery bank to
achieve higher charging current. Each controller must have its own solar panel(s).
• Installation must be completed in accordance with applicable local standards.
Page 8 MPPT Solar Controller Owners Manual Rev. 1.0.
2.2 PV ARRAY REQUIREMENTS
(1) MAXIMUM PV ARRAY POWER
The MPPT controller has the function of charging current/power-limiting, that is, during the charging
process, when the charging current or power exceeds the rated charging current or power, the controller
will automatically limit the charging current or power to the rated range, which can eectively protect the
charging parts of controller, and prevent damages to the controller due to the connection of some
over-specication PV modules. The actual operation of PV array is as follows:
Condition 1:
Actual charging power of PV array ≤ Rated charging power of controller
Condition 2:
Actual charging current of PV array ≤ Rated charging current of controller
When the controller operates under “Condition 1” or “Condition 2”, it will carry out the charging as per the
actual current or power; at this time, the controller can work at the maximum power point of PV array.
Condition 1:
Actual charging power of PV array＞Rated charging power of controller
Condition 4:
Actual charging current of PV array＞Rated charging current of controller
When the controller operates under “Condition 3” or “Condition 4”，it will carry out the charging as per
the rated current or power.
WARNING
When the power of PV is not greater than the rated charging power, but the maximum open-circuit
voltage of PV array is more than 100V (at the lowest environmental temperature), the controller
may be damaged.
WARNING
When the power of PV module is greater than the rated charging power, and the maximum
open-circuit voltage of PV array is more than 100V (at the lowest environmental temperature), the
controller may be damaged.
www.enerdrive.com.au Page 9
MODEL RATED CHARGE
CURRENT
RATED CHARGE
POWER
MAX. PV ARRAY
POWER
MAX. PV OPEN
CIRCUIT VOLTAGE
According to “Peak Sun Hours diagrams”, if the power of PV array exceeds the rated charging power of
controller, then the charging time as per the rated power will be prolonged, so that more energy can be
obtained for charging the battery. However, in the practical application, the maximum power of PV array
shall be not greater than 1.5 x the rated charging power of controller. If the maximum power of PV array
exceeds the rated charging power of controller too much, it will not only cause the waste of PV modules,
but also increase the open-circuit voltage of PV array due to the inuence of environmental temperature,
which may make the probability of damage to the controller rise. Therefore, it is very important to
congure the system reasonably.
For the recommended maximum power of PV array for this controller, please refer to the table below:
At 25˚C environment temperature
At minimum operating environment temperature
CAUTION
When the PV modules connect in series, the open circuit voltage of the PV array must not exceed 92V
at 25°C environment temperature.
EN43510 130W/12V
260W/24V
195W/12V
390W/24V
260W/12V
520W/24V
390W/12V
780W/24V
390W/12V
92V
100V
780W/24V
580W/12V
1170W/24V
780W/12V
1560W/24V
520W/12V
1040W/24V
20A
10A
30A
40A
EN43520
EN43530
EN43540
Page 10
NOTE: All PV modules in a given array are assumed to be identical.
＊Isc=short circuit current(amps) Voc=open circuit voltage.
＊These are the maximum wire sizes that will t the controller terminals.
2.3 WIRE SIZE
MPPT Solar Controller Owners Manual Rev. 1.0.
The wiring and installation methods must conform to all national and local electrical code requirements.
Since PV array output can vary due to the PV module size, connection method or sunlight angle, the
minimum wire size can be calculated by the Isc＊of PV array. Please refer to the value of Isc in the PV
module specication. When PV modules connect in series, the Isc is equal to a PV modules Isc. When PV
modules connect in parallel, the Isc is equal to the sum of the PV modules’Isc. The Isc of the PV array must
not exceed the controller’s maximum PV input current. Please refer to the table as below:
PV WIRE SIZE
MODEL MAX. PV
INPUT CURRENT
MAX. PV
WIRE SIZE*
EN43510 4MM²/12AWG
16MM²/6AWG
16MM²/6AWG
16MM²/6AWG
10A
20A
30A
40A
EN43520
EN43530
EN43540
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Controladores de Dometic
Dometic
Dometic Go Power! GP-RVC-R Manual de usuario
Dometic
Dometic GP-PWM-10-FM Manual de usuario
Dometic
Dometic Go Power! GP-SB-PWM-10 Manual de usuario
Dometic
Dometic TankManager Manual de usuario
Dometic
Dometic Go Power GP-PWM-10-SQ Manual de usuario
Dometic
Dometic SmartStart SMRTSTACRV Manual de usuario
Dometic
Dometic WAECO ASC G WI-FI KIT Manual de usuario
Dometic
Dometic GP-MPPT-100/30 Manual de usuario
Dometic
Dometic Go Power! GP-SB-PWM-10 Manual de usuario
Dometic
Dometic 30AMP PWM Manual de usuario
Dometic
Dometic Go Power! GP-SB-PWM-10 Manual de usuario
Dometic
Dometic Go Power! GP-SB-PWM-30BT Manual de usuario
Dometic
Dometic GoPower! GP-MPPT-85/20 Manual de usuario
Dometic
Dometic GP-MPPT-60/10 Manual de usuario
Dometic
Dometic GP-MPPT-100/30 Manual de usuario
Dometic
Dometic Go Power GP-PWM-10-SQ Manual de usuario
Dometic
Dometic Optimus Adaptive Trim Tab System Manual de usuario
Dometic
Dometic SmartStart III Manual de usuario
Dometic
Dometic SmartStart SMRTSTACRV Manual de usuario
Dometic
Dometic EA1000 Manual de usuario
