DMP Electronics XTL Series Manual de usuario

Information furnished by DMP is believed to be accurate and reliable.

This information is subject to change without notice.

Silencing an Alarm

When the alarm siren is sounding, enter your user code or present your card to

a keypad during the Status List display.

All/Perimeter or Home/Sleep/Away System

CANCEL VERIFY displays.

• Ifaburglaralarmisvalid,pressVERIFYtosendavericationmessage

to the Central Station.

• Ifavalidalarmhasnotoccurred,pressCANCELtocancelthealarm

and send an Abort or Cancel message to the Central Station. The

keypad displays ALARM CANCELLED and the security system will be

disarmed.

What to do when a trouble tone is sounding

You can silence the trouble tone by pressing any key. This only silences the

keypad and does not correct the condition that originally caused the problem.

XTL User’s Guide i

XTL User’s Guide

Table of Contents

Section Page Section Page

Silencing an Alarm.....................................................b

Introduction ..............................................................1

About Your Security System .............................................1

Emergency Evacuation Plans............................................2

Keypads .........................................................................3

Special Keypad Tones ......................................................4

1100 Series Wireless ......................................................5

Special Wireless Displays ................................................6

Special Keypad Displays...................................................6

Email/Cell Phone Messages ..............................................7

MyAccess™ Text Messaging Commands ............................7

Arming and Disarming............................................... 9

How Your System Operates..............................................9

Arming Functions ............................................................9

Key Fob Arming............................................................. 10

Key Fob Disarming ........................................................ 10

All/Perimeter System Arming.......................................... 10

All/Perimeter System Disarming...................................... 11

Home/Away System Arming ........................................... 12

Home/Away System Disarming....................................... 13

Area System Arming...................................................... 14

Area System Disarming.................................................. 15

Keypad Shortcut Keys.................................................... 16

User Menu ...............................................................18

Accessing the User Menu ............................................... 18

User Menu Options........................................................ 18

User Check-in................................................................ 19

Zone Activity Check ....................................................... 19

Sensor Reset................................................................. 20

Outputs On Off ............................................................ 20

Favorite ........................................................................ 20

Bypass Zones................................................................ 21

Zone Monitor (Chime).................................................... 21

Using the Zone Monitor Function .................................... 22

System Test .................................................................. 22

User Codes ................................................................... 23

Schedules ..................................................................... 25

Permanent Schedules .................................................... 26

Extending Schedules ..................................................... 26

Time and Date .............................................................. 26

Display Events .............................................................. 27

ii XTL User’s Guide

System Setup ..........................................................28

System Setup Record..................................................... 28

Protection Areas............................................................ 28

Output Record .............................................................. 28

Favorite List .................................................................. 29

Key Fob Button Programming ........................................ 30

User Codes ................................................................... 30

Appendix A ..............................................................32

About the Display Events Section.................................... 32

Zone Activity Check Event Display .................................. 32

Zone Bypass Event Displays ........................................... 32

Zone Event Displays ...................................................... 33

Arming and Disarming Event Displays ............................. 33

User Check-in Event Displays ......................................... 33

User Code Change Event Displays .................................. 33

Supervisory Event Displays ............................................ 34

System Monitor Event Displays....................................... 34

Wireless Jamming Event Displays ................................... 34

Appendix B ..............................................................35

1100 Series Wireless Description ................................... 35

Appendix C ..............................................................36

User’s Guide ................................................................. 36

Entering User Names .................................................... 38

Appendix D ..............................................................39

Email/Cell Phone Message User’s Guide .......................... 39

MyAccess™ Text Messaging Commands .......................... 40

Subscribe to Text Messages ........................................... 42

Common Keypad Displays .............................................. 43

Quick Reference Wallet Cards.................................46

XTL User’s Guide 1

Introduction

About Your Security System

Your system is designed with your safety and comfort in mind. It

uses the latest in computer technology to create the most advanced,

userfriendly,wirelesssecurityandresystemavailable.

The system combines ease of use with a simple to understand

keypad display to offer the full range of features requested by

today’s security system owners. Your security system can protect

both the interior and perimeter of your home or business while you

are away or just the perimeter when you are inside, giving you a

wall of security and peace of mind.

You can turn portions of your protection on or off at any time by

pressing a few keys. You can add, delete, and change personal user

codes at any time or check the status of all protection devices in

the system.

Keypads

This is the device we have placed at certain locations throughout

the premises that allows you to turn the system protection on and

off using your personal user code.

Keypad User Menu

The keypad provides a simple User Menu containing all of the

functions you need to fully operate your system such as performing

a system test or changing a personal user code.

A Note About False Alarms

One of the most important concerns facing the security industry

today is false alarms. The accidental dispatching of police and

re agencies places others in jeopardy by limiting the response

capability of those emergency service units.

As part of our commitment to reducing false alarms, we would like

to encourage you to read this guide thoroughly. All the information

contained here can help you quickly, and comfortably, learn the

XTL system operation.

Note: There may be a 30-second alarm communication delay

pre-programmed at installation to allow disarming if a false alarm

occurs. This delay is optional and can be removed or increased to

45 seconds by your alarm dealer.

Test Your System Weekly

It is recommended that you test the burglary portion of your system

at least once each week. Testing should involve an active test of all

doors, windows, and motion detectors connected to your system.

Ifyoursystemalsohasreprotection,calltheservicedepartment

tondouthowthisportionofyoursystemshouldbetested.

Refer to the System Test section of this guide for instructions on

testing the burglary portion of your system.

2 XTL User’s Guide

Practice your escape plans

Devising an escape plan is only the beginning. For the plan to be

effective everyone should practice escape routes from each room.

Second Floor

Building Front Building Back

Firt Floor

Fire cae

indo adder

Figure 1: Sample Escape Route Map

Early detection

The best way to survive a re or other emergency is to get out

early.  A re alarm system installation, with smoke and carbon

monoxide detectors in each room, can greatly decrease your risk

of loss or injury.

Emergency Evacuation Plans

Overview

The National Fire Protection Association recommends that you

establish an emergency evacuation plan to safeguard lives in the

eventofareorotheremergency.

Draw a floor plan of your home or business

On a clean sheet of paper, draw the walls, windows, doors, and

stairs. Also draw any obstacles that a person may encounter while

exiting the building such as large furniture or appliances.

Develop escape routes

Determine at least two routes the occupants in each room can

take to safely escape. One route can be the most obvious such

as the door. Another can be through an easily opened window.

If the window is high off the ground, an escape ladder should be

provided.

Draw arrows on the oor plan to show escape routes from each

room.

Decide where to meet

Prearrange a meeting place outside and away from where

emergency personnel are likely to be working. A neighbor’s house

or across the street in front of the house are good locations. Always

perform a head count to make sure all occupants safely exited.

NEVER ENTER A BURNING BUILDING. If the head count shows one

or more persons missing, give this information immediately to the

authorities. Never enter a building to look for someone.

Introduction XTL User’s Guide 3

Keypads

Your system has an easy to use LCD keypad that allows you to

properly operate the system.

The Select keys

There are four keys under the display called the Select keys. These

keys are one of the features that make your system so easy to

operate. They allow you to make selections by pressing the Select

key under a choice shown in the display.

Note: For the purposes of this guide, when instructed to press

the rst Select key, press the far left Select key; the second

Select key is the second from the left; third Select key is second

from the right; and the fourth Select key is the far right key.

Power/Armed Logo

The backlit logo on the keypad

indicates the keypad Power status

and Armed status of the panel. Depending on the operation, the

logo displays Red or Green as listed in the table.

Color and Activity Armed Status Keypad Power Status

Green Steady Panel Disarmed AC Power OK, Battery OK

Green Blinking Panel Disarmed AC Power OK, Battery Fault

No Light Panel Disarmed AC Power Fault, Battery OK

Red Steady Panel Armed AC Power OK, Battery OK

Red/Green Alternate Panel Armed AC Power OK, Battery Fault

Red Blinking Panel Armed AC Power Fault, Battery OK

Panic Functions

Your keypad may be set up to send a Panic, Emergency, or Fire

report to the central station. This function is optional. If this

option is programmed for your keypad, icons are located below the

top row Select keys.

Press and hold the two Select keys adjacent to the desired icon for

2 seconds, until a beep from the keypad is heard.

Top Row Select Keys

PoliceEmergency Fire

DMP 9000 Series Wireless Keypad Panic Keys

With Shaded Buttons To Indicate Police Panic Keys

32-Character Display

Data Entry Digit keys

COMMAND Key

Back Arrow Key

Select Keys

1 2 3 4

9 0 CMD

5 6 7 8

ABC PRINTING

FRI 2:51 AM

Backlit Logo

and Proximity

Antenna

DMP 9000 Series Wireless Keypad

4 XTL User’s Guide Introduction

Common Keys on All Keypads

Data Entry Digit keys

These keys allow you to enter your user code when arming or

disarming or enter other information into the system.

COMMAND (CMD) key

The COMMAND key allows you to advance through the keypad

displays, User Menu, or complete a data entry function.

Back Arrow (<—) key

The Back Arrow (<—) key is used to go back through the keypad

displays while operating your system. You can press the Back Arrow

key to back up through the list of functions in the User Menu or to

erase the last character you entered.

Keypad User Options

The User Options menu allows you to make adjustments to your

keypadtobesttyourenvironmentandneeds.

Press and hold the Back Arrow and COMMAND keys for two seconds.

The keypad display changes to SET BRIGHTNESS. Press the COMMAND

key to display the next option or the Back Arrow key to exit.

Backlighting Brightness

At the SET BRIGHTNESS display, use the left Select key to lower

the keypad brightness. Use the right Select key to increase the

brightness.

Note: If the brightness level is lowered, it temporarily reverts back

to maximum intensity whenever a key is pressed.

Internal Speaker Tone

Set the tone of the keypad internal speaker. At the SET TONE

display, use the top left Select key to make the tone lower. Use

the right Select key to make the tone higher.

Volume level

Set the volume level of the keypad internal speaker for key presses.

During alarm, trouble, and prewarn conditions, the volume is always

at maximum level. At SET VOLUME LEVEL, use the left Select key

to lower the keypad volume. Use the right Select key to raise the

volume.

Serial Number

The serial number assigned to the keypad displays. Press the Back

Arrow key to exit the User Options function.

Special Keypad Tones

Your keypad also contains a speaker that alerts you about events

as they occur on your system. For burglary alarms, the tone will

silenceassoonastherstusercodedigitkeyispressed.Ifavalid

user code is not entered within 5 seconds or an invalid user code is

entered, the burglary tone begins sounding again.

Below are brief descriptions of the different tones you hear from

the keypad.

Fire alert: An intermittent sweeping siren that continuously repeats

untilthe re alarmis silenced.Thisis inaddition toaseparate

siren activated by the alarm panel.

Burglary alert: A siren tone that continues until the alarm is

silenced. This is in addition to the separate siren output operated

by the alarm panel.

Key press tone: A short beep as you press a key on the keypad.

Introduction XTL User’s Guide 5

Prewarn tone: A continuous pulsed tone that sounds when you

open an entry delay door on a system that is armed (turned on)

reminding you to disarm the burglary protection.

Your system will silence the tone as soon as the rst user code

digit key is pressed. If a valid user code is not entered within 5

seconds or an invalid user code is entered, the prewarn tone begins

sounding again.

Exit tone: When fully arming your system to leave, a continuous

pulsing tone sounds during the exit countdown just after arming to

remind you to exit the premise. At ten seconds prior to the end of

the countdown, the rate of pulsing increases.

Monitor tone: A pulsed tone that sounds one time for one second

each time a door or window is opened while you are using the zone

monitor function from the User Menu. See Zone Monitor.

Trouble tone: A steady tone indicating a trouble condition on your

system. Press any key to silence the trouble tone.

What to do when the trouble tone sounds

You can silence the trouble tone by pressing any key.

This only silences the keypad and does not correct the

condition that originally caused the trouble.

1100 Series Wireless

Your system may include wireless devices such as key fob(s). There

are three types of wireless key fobs available:

4-Button Model 1145 Key Fob

2-Button Model 1146 Key Fob

1-Button Model 1147 Key Fob

The drawing shows the button

layout for all three models for your

reference. Each button on the key

fob is programmed to perform a

specic action.  The button names

are listed for your reference.

TOP = the Key Fob Top button

BTM = the Key Fob Bottom button

LFT = the Key Fob Left button

RGT = the Key Fob Right button

The button programming list for the

key fob(s) connected to your system

is located in the System Setup section

of this guide. Refer to Appendix B for

LED Status operation information.

Specicfunctionlabelscanbeadded

to each button to indicate button

operation.

For best operation, allow the LED

to turn on and then turn off before

pressing another button. The key

fob may not complete sending the

signal for the button press if another

button is pressed too quickly.

Connect Keyring or Lanyard Here

LED

2-Button Layout 1-Button Layout

4-Button Layout

TOP

BTM

LFT RGT

Key Fob Examples and

Button Names

6 XTL User’s Guide Introduction

ALARM CANCELLED

An Alarm signal just sent to the central station was cancelled

because a user code was entered after the alarm was sent. Also,

an Alarm Cancel signal is sent to the Central Station.

ALARM VERIFIED

Avalidburglaralarmhasoccurredandhasbeenmanuallyveried

by the user. The alarm system also transmits a VERIFY message to

the Central Station.

ENTER CODE

The system requires you to enter a personal user code. User codes

can be used for turning your system on (arming), turning your

system off (disarming), and other system options.

As you enter your user code, the keypad display shows an asterisk

(*) in place of each digit pressed. This prevents others from seeing

your user code on the display as you enter it.

INVALID CODE or TRY AGAIN

The user code you entered is not recognized by the system. Check

the user code and try again.

TRBL (TROUBLE)

There is a problem with a protection device or system component.

This display is accompanied by a description of the problem.

SYSTEM TROUBLE or SERVICE REQUIRED

There is an electronic failure in your system. Contact the service

department as soon as possible.

TEST IN PROGRESS

The system is currently being tested by an installation or service

technician.

Special Wireless Displays

Your system uses wireless transmitters to send alarm and trouble

information from the protection devices to the panel. Wireless

systems have several unique keypad displays.

BACK DOOR -LOBAT - (Low Battery) The battery in a wireless

transmitter is low. (BACK DOOR is used as an example only.)

BACK DOOR -MISNG - (Missing) The panel is not receiving the

wireless transmitter periodic test report.

WIRELESS -TRBL - (Trouble) Some part of your wireless system is

operating improperly. Call the service department for assistance.

WIRELESS RECEIVER JAMMED -ALARM - Your system may be programmed

for wireless interference detection and, if displayed, your wireless

receiver has detected an interfering signal while the system is armed.

WIRELESS RECEIVER JAMMED -TRBL - (Trouble) Your system may be

programmed for wireless interference detection and, if displayed,

your wireless receiver has detected an interfering signal while the

system is disarmed.

Special Keypad Displays

As you use your system, you may occasionally see a keypad display

that asks you to enter a user code or describes a condition on the

system. Below are some examples of the displays you may see.

ALARM

A24-hourzone,suchasareorpaniczone,oranarmedburglary

zone is faulted. Your system may also sound wireless sirens.

ALARM NOT SENT

The alarm signal was aborted and was not sent to the central station

because a user code was entered to disarm the system before the

alarm signal was sent to the central station. Also, your system may

be pre-programmed at installation to send an Abort signal to the

Central Station. Refer to the Introduction section.

Otros manuales para XTL Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de seguridad de DMP Electronics

DMP Electronics

DMP Electronics CELLCOMSL SERIES Instrucciones de funcionamiento

DMP Electronics

DMP Electronics XR500 SERIES Manual de usuario

DMP Electronics

DMP Electronics XR100FC Manual de usuario

DMP Electronics

DMP Electronics 1135DB Manual de usuario

DMP Electronics

DMP Electronics XR500 SERIES Manual de usuario

DMP Electronics

DMP Electronics DUALCOM Series Manual de instalación y funcionamiento

DMP Electronics

DMP Electronics XR500 SERIES Manual de usuario

DMP Electronics

DMP Electronics SecurityCommand XR10 Manual de usuario

DMP Electronics

DMP Electronics iComSL Series Manual de usuario

DMP Electronics

DMP Electronics 1135 Series Manual de usuario

DMP Electronics

DMP Electronics 893A Instrucciones de montaje

DMP Electronics

DMP Electronics 1912XR Manual técnico

DMP Electronics

DMP Electronics 1136 Manual de usuario

DMP Electronics

DMP Electronics XTLtouch Manual de usuario

DMP Electronics

DMP Electronics XT30 Series Manual de usuario

DMP Electronics

DMP Electronics 1135 Manual de usuario

DMP Electronics

DMP Electronics XR150 series Manual de usuario

DMP Electronics

DMP Electronics 135 Series Manual de usuario

DMP Electronics

DMP Electronics Thinline 7063 Manual de usuario

DMP Electronics

DMP Electronics Security Command XR20 Manual de usuario

DMP Electronics

DMP Electronics 1135 Manual de usuario

DMP Electronics

DMP Electronics 265HINT Manual de usuario

DMP Electronics

DMP Electronics 263HINT Manual de usuario

DMP Electronics

DMP Electronics SCS-1R Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario