Designed, engineered, and
manufactured in Springfield, MO
using U.S. and global components.
LT-1669 21015
1136 WIRELESS REMOTE CHIME
Specifications
Frequency Range 905-924 MHz
Color White
Housing Material Flame retardant ABS
Dimensions 2.6 in W x 5 in H x 1.5 in D
6.6 cm W x 12.7 cm H x 3.8 cm D
Certifications
FCC Part 15 Registration ID CCKPC0193
Industry Canada Registration ID 5251APC0193
Patents
U.S. Patent No. 7,239,236
INTRUSION • FIRE• ACCESS• NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
800.641.4282 | DMP.com
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons. It must not be located or operated in conjunction
with any other antenna or transmitter.
Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA INFORMATION
This device complies with Industry Canada Licence-exempt RSS standards. Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.
This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by Health Canada Safety Code 6. The system must be installed at a minimum
separation distance from the antenna to a general bystander of 7.87 inches (20 cm) to maintain compliance with the General Population limits.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites établies par le Code de sécurité 6 de Santé Canada. Le système
doit être installé à une distance minimale de 7.87 pouces (20 cm) séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand public.
© 2021
4TEST THE 1136
After the 1136 has been programmed and plugged in to an outlet, test the 1136 to confirm that it is
communicating clearly with the panel. Use the Tech APP™ to perform a Sensor Test on the system, or follow
these steps to perform a Walk Test from a keypad connected to the system:
1. At the keypad, enter 8144 (WALK) and select WLS.
2. If the 1136 fails to check in at the keypad, relocate it to a dierent outlet.
PLUG IN THE 1136
Once you have located an outlet with confirmed communication to the panel, plug in the 1136.
Caution: To reduce the risk of electric shock, do not remove or open the 1136’s cover.
3
ADDITIONAL PROGRAMMING
When using an XR Series Panel, to receive notifications that there is a trouble on the 1136, go to the AUX 1 ZONES in
Status List and enter in which keypad addresses you would like to receive notifications. See the Status List section of the
XR150/XR550 Programming Guide (LT-1232) for more information.
