DMP Electronics 1128 Manual de usuario

DESCRIPTION

Figure 1: 1128 Wireless

Glassbreak Detector

1PROGRAM THE PANEL

When programming the 1128 in the panel, refer to the panel

programming guide as needed.

1. At a keypad, enter 6653 (PROG) to access the

PROGRAMMER menu.

2. Press CMD until ZONE INFORMATION displays and

press a top row select key or area.

3. Enter the wireless ZONE NO and press CMD.

4. Enter the ZONE NAME and press CMD.

5. Select NT (night) the ZONE TYPE.

6. Select the AREA NO and press CMD.

7. At the NEXT ZN? prompt, select NO and press CMD

until WIRELESS? displays.

8. Select YES when WIRELESS? displays and press

CMD.

9. Enter the eight-digit SERIAL# and press CMD.

10. Enter the SUPRVSN TIME and press CMD.

11. At the NEXT ZN? prompt, select YES if you are

ﬁnished programming the zone. Select NO if you

would like to access additional programming

options.

2INSTALL THE BATTERY

Keep in mind, when setting up a wireless system, program

zones and connect the receiver before installing the included

CR123A battery in the transmitter.

1. Remove the holding screw at the lower end of the

1128 case and gently lift o the cover. See Figure 2.

2. Observing polarity, place the battery in the holder

and press into place. See Figure 3 for the battery

location.

The 1128 Wireless Glassbreak

Detector is a fully-supervised,

low current shock and

glassbreak sensor that

provides detection coverage

up to 20 ft from framed glass

mounted in an outside wall.

You can mount the 1128 on

the ceiling or on an opposing

wall for maximum ﬂexibility

and coverage. The 1128

operates using the supplied

3 V lithium battery.

Compatibility

All DMP 1100 Series

Wireless Receivers.

Glassbreak Walk Test is

available on 1128 Version

2.0.0.1 and higher and with

XT/XR Series Version 191

and higher. See last page

for compatibility details.

What is Included?

• One 1128 Wireless

Glassbreak Detector

• One 3 V lithium

CR123A battery

• Hardware Pack

Figure 2: Open the 1128

Figure 3: 1128 Battery Location

LED

Holding

Screw

Tamper

Battery

Holder

1128 WIRELESS GLASSBREAK DETECTOR

Installation Guide

2 1128 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS

The 1128's omni-directional detection coverage is measured from the 1128 to the point on the glass

farthest from the 1128. Refer to the table below to determine the best location to place the 1128 based

on window type, glass thickness, window to wall range, and wall type.

Note: The sensor can be mounted as close as 3.3' (1 m) from the glass and the minimum glass

size is 1' x 2' (0.3 m x 0.6 m).

3SELECT A LOCATION

Window Type Glass Thickness Maximum Range Wall Type

Plate 3/32" - 1/4" (2.4mm - 6.4mm) 20' (6m) Opposite, adjoining, ceiling

Tempered 1/8" - 1/4" (3.2mm - 6.4mm) 20' (6m) Opposite, adjoining, ceiling

Laminated 1/8" - 1/4" (3.2mm - 6.4mm) 20' (6m) Opposite, adjoining, ceiling

Wired 1/4" (6.4mm) 20' (6m) Opposite, adjoining, ceiling

Armor-coated N/A 12' (3.65m) Opposite, adjoining, ceiling

Optimize Detection

To optimize detection, install the 1128 in the following areas:

• Large rooms with moderate noise

• In the direct line of sight of all windows that are to be protected

• On the opposite wall of the window that it's protecting (see Figure 4 for detection range)

20 ft (6m)

Figure 4: 1128 Detection Range

Avoid False Alarms

To avoid false alarms, do not install the 1128 in the following areas:

• Rooms with lined, insulated, or dampening drapes

• Rooms with closed, wooden shutters on the inside

• Room corners

• Where white noise (air compressor) is present

• Rooms smaller than 10'x10'

• Rooms with multiple noise sources like televisions, sinks, speakers, etc.

• Excessively humid rooms

Note: Avoid programming the 1128 as a day or supervisory zone to help avoid false

alarms.

Check the Location Using the Survey LED

1. Hold the 1128 in the exact desired location.

2. Press the tamper switch to send data to the receiver and determine if communication is

conﬁrmed or faulty. See Figures 2 and 3 for tamper switch and LED locations.

Conﬁrmed: If communication is conﬁrmed, the survey LED turns on when data is

sent to the receiver and o when acknowledgement is received. Repeat this test to

conﬁrm ﬁve separate consecutive LED blinks. Any indication otherwise means proper

communication has not been established.

Faulty: If communication is faulty, the LED remains on for several seconds or ﬂashes

multiple times in quick succession.

Relocate the 1128 or receiver until the LED conﬁrms clear communication. Proper

communication between the 1128 and receiver is veriﬁed when for each press or release

of the tamper switch, the LED blinks immediately on and immediately o.

1128 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3

1. With the 1128 already open, place the 1128 base on the

wall in the desired location.

2. Use the provided hardware pack to mount the base to

the wall. See Figure 5 for mounting hole locations.

3. Reinstall the 1128 cover back on to the base and tighten

the holding screw.

4MOUNT THE 1128

5TEST THE 1128

Handheld Glassbreak Test

To test the 1128, use a hand-held tester like the FG-701 to imitate

glass breaking. For more information, refer to the glassbreak

tester manual.

1. Set the tester to ﬂex mode.

2. Place the FG-701 near the protected glass and press the

button to activate the simulator. It will not annunciate

the sound of shattering glass until a low-frequency

shock is also generated.

3. To generate the shock, slam a framed door to generate

the appropriate low-frequency shock. The shock will

also activate the FG-701 simulator.

Note: The 1128 has two onboard microphones. Both the high frequency and low

frequency microphones must be activated to send an alarm to the control panel. If

only the low frequency microphone activates, the LED on the 1128 will ﬂash green.

When both activate, the LED will ﬂash red and the 1128 will transmit an alarm to the

control panel.

Glassbreak Walk Test (v2.0.0.1 and higher)

When the 1128 is set into testing mode from the panel, it will trip using the tester only. There is no

need to generate shock to trip the detector. XT and XR Series ﬁrmware Version 191 is required to

perform the glassbreak walk test.

1. Reset the panel.

2. Type 8144 (WALK) and select PIR. All 1128s on the system will begin ﬂashing a green LED

every 3 seconds to indicate that they are in testing mode. It can take up to 3 minutes for all

1128s to enter testing mode.

Note: The PIR option will enable testing of all supported wireless PIRs and 1128s on the

system.

3. Set the tester to manual mode.

4. Place the FG-701 near the protected glass and press the button to activate the simulator. If

the 1128 is in range, it will ﬂash the LED red for 3 seconds to indicate it detected the crash.

5. The 1128 will remain in testing mode for 30 minutes or until the panel is reset.

Wireless Check-in Test

Perform a Wireless Check-in Test to conﬁrm that the 1128 is communicating clearly with the panel.

1. At the keypad, enter 8144 (WALK) and select WLS.

2. If the 1128 fails to check in at the keypad, relocate the 1128 or the receiver.

MOUNTING HOLES

Figure 5: Mounting Holes

Replace the Battery

1. Remove the holding screw and open the 1128 housing.

2. Remove the old battery from the holder.

3. Observe polarity and insert the new battery in the holder (3 V lithium CR123A battery).

4. Replace the cover on the 1128 and secure the housing with the holding screw.

ADDITIONAL INFORMATION

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

866.266.2826 | DMP.com

LT-1825 21203

Speciﬁcations

Battery

Life Expectancy 3 Years (normal operation)

Type 3 V lithium CR123A

Frequency Range 905-924 MHz

Transmit Condition Alarm, Low Battery, Tamper

Detection Method Omni-directional

Range 20 ft (6 m)

Operating Temperature -10°C to +55°C

Color White (passes VW1)

Housing Material Flame retardant ABS

Dimensions 3.3"L x 2.1"W x 0.9"D

Weight 4.2 oz.

Compatibility

• All DMP 1100 Series Wireless receivers and

transmitters v106 and higher

Note: If the 3rd digit of the transmitter's serial

number is greater than 0, it will be v106 or

higher. If the 3rd digit is equal to zero, that

transmitter must be removed or replaced with

a newer transmitter for the 1128 to function

properly.

• All DMP Burglary Panels with built-in 1100

Series Wireless

• Test Mode requires XT/XR Series Version

191 ﬁrmware

Certiﬁcations

FCC Part 15 Registration ID CCK1128

IC Registration ID 5251A-1128

Accessories

FG-701 Glassbreak Simulator

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all

persons. It must not be located or operated in conjunction with any other antenna or transmitter.

Changes or modiﬁcations made by the user and not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA INFORMATION

This device complies with Industry Canada Licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

1. l’appareil ne doit pas produire de brouillage, et

2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits speciﬁed by Health Canada

Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general bystander of 7.87

inches (20 cm) to maintain compliance with the General Population limits.

L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites établies

par le Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces (20 cm) séparant

l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand public.

1128 WIRELESS GLASSBREAK

DETECTOR

Otros manuales de Sensor de seguridad de DMP Electronics

DMP Electronics

DMP Electronics 1166 Manual de usuario

DMP Electronics

DMP Electronics 1124 Manual de usuario

DMP Electronics

DMP Electronics XTLplusINT Series Guía de instalación

DMP Electronics

DMP Electronics 1183 Series Manual de usuario

DMP Electronics

DMP Electronics 1121-WINT PIR Instrucciones de montaje

DMP Electronics

DMP Electronics 1127C Manual de usuario

DMP Electronics

DMP Electronics SR3 Manual de usuario

DMP Electronics

DMP Electronics 1127W-WINT Instrucciones de montaje

DMP Electronics

DMP Electronics DEL AOP PRO 50 Manual de usuario

DMP Electronics

DMP Electronics 1125 Instrucciones de montaje

DMP Electronics

DMP Electronics 1126R Manual de usuario

DMP Electronics

DMP Electronics 1168 Guía de instalación

DMP Electronics

DMP Electronics 1126 Series Instrucciones de montaje

DMP Electronics

DMP Electronics 1184 Manual de usuario

DMP Electronics

DMP Electronics 1127W Manual de usuario

DMP Electronics

DMP Electronics 1128 Manual de usuario

DMP Electronics

DMP Electronics XTLtouch International Series Manual de usuario

DMP Electronics

DMP Electronics XR Series Manual de usuario

DMP Electronics

DMP Electronics 1125 Instrucciones de montaje

DMP Electronics

DMP Electronics 1129 WIRELESS GLASSBREAK DETECTOR Manual de usuario

DMP Electronics

DMP Electronics 1135INT Series Manual de usuario

DMP Electronics

DMP Electronics 1128INT Manual de usuario

DMP Electronics

DMP Electronics 1183-135F Manual de usuario

DMP Electronics

DMP Electronics 1161 Manual de usuario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario

Solinst

Solinst 301 Manual de usuario