Dish Network HDE-8C-QAM Manual de usuario

• Connect the unit as pictured to the right:

• Locate the receiver labels numbered 1 through 9 in the plastic bag

supplied with the encoder.

• Find the receiver ID number label on the rst receiver. Write the last

4 digits of the ID on label #1 (RX1_####__) and place on the front of

the receiver.

• Repeat for all 9 satellite receivers (8 primary plus 1 optional spare).

• Now connect each receiver output to the encoder inputs, making

sure that receiver #1 (RX#1) is connected to #1 component input on

the encoder. Repeat this process for remaining receivers.

• Connect the Receivers Control 10/100 port on the encoder (see

section 2.2 #11 in manual) to an Ethernet switch (with a minimum of

10 ports) with a CAT 5 jumper cable.

• Connect the 9 satellite receivers to the same switch.

• Power up the receivers and the encoder.

• Log in to the HDE-8C-QAM, using a standard web browser. This can

be done through the Control 10/100 port, next to the Receiver

Control port. Either go directly from a computer or through an

Ethernet switch

• Assign 172.16.70.2 as the static address for your computer

• Now open your browser and enter 172.16.70.1 to access the

HDE-8C-QAM.

• The Username is “Admin” and the password is “pass”

STEP 2

HDE-8C-QAM QUICK GUIDE

STEP 1

IP=172.16.70.1

IP=172.16.70.2

Optional Spare

10/100

Ethernet

Document # 651235400A Stock # 6370-1

To download instrucon manual visit www.BlonderTongue.com | 800-523-6049

(For supported Dish Network Receivers)

• Setup the QAM output channels by going to the

Main > Output > QAM tab

• Select the channel for the 1st QAM. The next 3 will be

automatically assigned.

• Ensure all outputs are on and CW mode is not enabled.

• Click “SAVE” to apply changes.

STEP 3

• If not already, allow several minutes for the receivers to be

discovered and assigned IP addresses

• From the Main > Input Cong Tab of the Web Pages, assign

RX#1 to Input #1, RX#2 to Input #2, etc.

• Click “SAVE” to apply changes.

STEP 4

STEP 5

To download instrucon manual visit www.BlonderTongue.com | 800-523-6049

• Go to the Main > Output > TS Cong Tab

• Verify the Multiplexed MPTS Output default settings are suitable

for your application

- TS bitrate = QAM Modulator

-Modulation Mode = QAM 256

-Out of band = disabled

• Verify the Output Mapping Section.

- Input for each TS must be different.

- Every PID and Program Number must be different.

- Short Name should be a descriptive name of the

program, as it will be shown on the television

(max 7 alphanumeric characters)

-Major and Minor Channel numbers are what the

TV will display as the channel.

• Click “SAVE” to apply changes.

Otros manuales de Receptor de Dish Network

Dish Network

Dish Network Duo ViP 222 Manual de usuario

Dish Network

Dish Network DishPro 322 Manual de usuario

Dish Network

Dish Network 311 Series Manual de usuario

Dish Network

Dish Network 111 Series Manual de usuario

Dish Network

Dish Network WALLY Manual de usuario

Dish Network

Dish Network Receiver Manual de usuario

Dish Network

Dish Network 622 guide Manual

Dish Network

Dish Network 196812 Manual de usuario

Dish Network

Dish Network 4K Joey Manual de usuario

Dish Network

Dish Network 512 Manual de usuario

Dish Network

Dish Network DuoDVR ViP 722_TOC Manual de usuario

Dish Network

Dish Network DuoDVR 625 Manual de usuario

Dish Network

Dish Network DP111 Manual de usuario

Dish Network

Dish Network DISH322 Manual de usuario

Dish Network

Dish Network ViP 222K Manual de usuario

Dish Network

Dish Network DVR Satellite System Manual de usuario

Dish Network

Dish Network SR200 Manual de usuario

Dish Network

Dish Network Satellite Television Manual de usuario

Dish Network

Dish Network Solo 381 Manual de usuario

Dish Network

Dish Network 4K Joey Manual de usuario

Dish Network

Dish Network SoloDVR ViP 612 Manual de usuario

Dish Network

Dish Network Hopper Manual de usuario

Dish Network

Dish Network Satellite Television Manual de usuario

Dish Network

Dish Network DISH 625 Instrucciones de funcionamiento e instalación

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario