Directed Directechs DB3 Manual de usuario
DB3 403.TL15
v1.15
2020 Toyota RAV4 (Smart Key)
Introduction 3
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Wiring diagram 6
Locating components in the vehicle 7
Vehicle connections 8
Module programming 10
Module programming for convenience only (skip transponder) 11
SmartStart/XL202 installation notes 12
Connecting the module 12
LED diagnostics and troubleshooting 14
Parking light error codes 16
Soft reset 16
Hard reset 16
Feature programming 17
Feature and option list 18
Limited one year consumer warranty 19
Quick reference guide 20
Contents
3403.TL15 1.15 2020 Toyota RAV4 (Smart Key)
©2023 Directed. All rights
Introduction
DB3 is an all-in-one door lock and override module. This guide supports the installation of a DB3 in Remote
Start Ready (RSR) mode. This solution may offer up to three (3) configuration options to control your system: 3x
OEM Lock Remote Start Activation (if applicable, refer to the “Vehicle function compatibilities” below), RF System
or SmartStart (all sold separately).
Warning!
This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs
Mobile application for smartphones. Refer to “Connecting the module” for more information.
4403.TL15 1.15 2020 Toyota RAV4 (Smart Key)
©2023 Directed. All rights
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.
Parking Lights Control
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Control of aftermarket alarm with OEM remote
Fuel level/EV battery level
* Odometer
Immobilizer Bypass-Data No Key Req'd
3x LOCK START (Start control using OEM Remote)
3x LOCK STOP (Stop control using OEM Remote)
RAP Shut Down (Retained ACC Power)
Remote Start Ready
SmartStart
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Factory Alarm Trigger Monitoring
Brake Status (foot brake)
E-Brake Status
Ignition Status
5403.TL15 1.15 2020 Toyota RAV4 (Smart Key)
©2023 Directed. All rights
Pre-installation and application warnings
START HERE This section highlights important information for this specific firmware and will assist in pricing accordingly, as
well as bringing awareness to any operational or vehicle limitations.
Compatibilities and Requirements
T-Harness
compatible T-Harness is not compatible.
AUX
Keys required for
programming 1Keys required
for operation 0
Vehicle Takeover Not available on Push-to-Start vehicles. The engine will stop when a door is open.
Firmware notes
Motorized Hatch: This feature needs to be enabled if available on your vehicle using the configuration tool found on the module
flashing page of www.directechs.com, or manual configuration of this feature is also possible. Refer to "Feature programming" for
more information.
Trunk release: Not covered with RSR installations.
Remote starting: all doors must be closed and locked.
OEM Remote starter: If the vehicle is already equipped with an OEM remote starter, the installer must disconnect it before installing
the DB3 otherwise it will not program. (For more information see "OEM remote starter detection").
Remote Start Ready (RSR) installations are not compatible with vehicles equipped with a manual transmission.
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own.
Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
SmartStart Compatible: SmartStart is equipped with D2D, which means it can be connected to an interface module and used in
Remote Start Ready (RSR) mode without the use of a remote starter. See "Module programming" for more information.
All connectors are displayed from the wire side (unless specified otherwise).
Refer to the "Vehicle connections" following the installation diagram.
Footnotes
[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin or if
not supported in data.
[2] SLP: Refer to "Vehicle connections" for help locating the Steering Lock Actuator Position Signal connector.
[3] PTS: Connection required for Ready mode for vehicles with hybrid engines.
[4] Telematics interrupt: Depending on the production date of your vehicle, if remote start fails, a "Telematics Interrupt" connection may
be required.
6403.TL15 1.15 2020 Toyota RAV4 (Smart Key)
©2023 Directed. All rights
Wiring diagram
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Autolight Interr. (conn. side): Yellow: 8
Autolight Interr. (veh. side): Orange/Yellow: 9
(+) 12V Input: Red: 13
(-) Ground: Black: 14
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 3
1412
10 42
6: White/Black:
(-) Hood Input
Remote Start Safety
Override Switch
Hood Pin
You can connect to either a
XL202 RFTD OR a SmartStart
module.
Refer to the SmartStart/XL202
Installation Notes for more
information.
(-) SLP Output: Brown/Red: 12
(-) Ground: Yellow/Red: 11
(-) Lock Output: Blue/Red: 12
(-) PTS Output: Green/Black: 2
(-) Unlock Output: Red/Black: 4
Black Steering Lock conn.
(at steering lock conn.)
Black PTS Button Conn.
(at PTS switch)
ENGINE
START
STOP
Black
Connector 2345
10 9 8 7 6
1
(-) PTS: Gray, pin 5
HS CAN Low:
Violet, pin 4
HS CAN High:
Tan, pin 5
1
(+) 12V: White, pin 1
Body ECU
Connector
Body ECU Connector
(Lower conn. left side
of steering column)
Body ECU
(middle conn.
left side of steering column)
678
1112131415161718 9
10
30 2122
232425262728 20
19
29
12345
678
111213
1415161718
9
10
21 20 19
12
3
45
Autolight:
Yellow, pin 5
123456781112131415161718 9
10
313233343536
3738 30 2122
232425262728 20 19
29
3940
Cut
Dash Fuse Box
(white conn.)
Headlight Switch
(white connector)
(-) SLP: Tan, pin 4
(-) Lock/Arm:
Lt. Green, pin 18
(-) Unlock/Disarm:
Tan, pin 17
86 85
30
87a
87
(-) GWR (status) Output: Black/White: 1
Fuse 5A
(+) 12V
19
14
6
1
56
36
33
Telematics
Interrupt:
Black, pin 33
Plug 3A
(white connector
rear of dash fuse box)
Telematics
Interrupt:
Brown, pin 6
AG4
(white conn. left
of body ECU)
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
9
10
20
19
OR
Cut
With
Start/Stop System
Without
Start/Stop System
7403.TL15 1.15 2020 Toyota RAV4 (Smart Key)
©2023 Directed. All rights
Locating components in the vehicle
1. Remove
metal clip
2. Remove white
plastic housing
Steering Lock Connector
Steering Lock
connector
1- To gain access to the SLP connector, remove metal clip to remove the white plastic housing.
2- Move the white plastic housing over enough to access the SLP cnnector.
8403.TL15 1.15 2020 Toyota RAV4 (Smart Key)
©2023 Directed. All rights
Vehicle connections
The connection information listed below is specific to the 2020 Toyota RAV4 (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes.
Data 14-pin blue connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H1/1 Light Green No Connection No Connection
H1/2 Violet/Yellow No Connection No Connection
H1/3 Tan/Black (DATA) HS CAN High Body ECU on dash fuse box, black 30 pin plug, pin 5 Data Tan
H1/4 Tan (DATA) HS CAN Low Body ECU on dash fuse box, black 30 pin plug, pin 4 Data Violet
H1/5 Orange/Green No Connection No Connection
H1/6 Orange/Brown No Connection No Connection
H1/7 Brown Relay N.O. No Connection No Connection
H1/8 Yellow Relay COM. Auto Light Interrupt (Conn. side) Headlight Switch, white 40 pin plug, pin 5 Cut Yellow
H1/9 Orange/Yellow Relay N.C. Auto Light Interrupt (Veh. side) Headlight Switch, white 40 pin plug, pin 5 Cut Yellow
H1/10 Orange/Red Relay N.C. No Connection No Connection
H1/11 Yellow/Red Relay COM. Ground (chassis ground)
H1/12 Brown/Red Relay N.O. SLP [2] Steering Lock Actuator on steering column, black 7 pin plug, pin 4 - Tan
H1/13 Red (+) 12 Volt Input Dash Fuse Box, white 1 pin plug (4L), pin 1 + White (50A)
H1/14 Black (-) Ground (chassis ground)
Output 12-pin red connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H2/1 Black/White (-) Ground When Running (Status) Input Dash Fuse Box, rear, white 56 pin plug (4A), pin 33
OR
Left of Dash Fuse Box, white 20 pin plug (AG4), pin 6
Must use a relay.
Cut
Cut
Black (w/o Stop-Start System)
Brown (with Stop-Start System)
H2/2 Green/Black (-) PTS Output [3] Push Start Switch, black 10 pin plug, pin 5 - Gray
H2/3 Green/White (-) Pk light output No Connection
H2/4 Red/Black (-) Unlock Output Body ECU on dash fuse box, black 21 pin plug, pin 17 Double
-
Tan (key unlock)
H2/5 Violet/White No Connection No Connection
H2/6 Gray (+) Starter Output No Connection
H2/7 Gray/Black No Connection No Connection
H2/8 Violet/Green No Connection No Connection
H2/9 Violet/Brown No Connection No Connection
H2/10 Yellow/Black No Connection No Connection
H2/11 Orange/Black No Connection No Connection
H2/12 Blue/Red (-) Lock Output Body ECU on dash fuse box, black 21 pin plug, pin 18 - Lt. Green (key lock)
9403.TL15 1.15 2020 Toyota RAV4 (Smart Key)
©2023 Directed. All rights
Input 10-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H3/1 Green No Connection No Connection
H3/2 Blue No Connection No Connection
H3/3 Red/White No Connection No Connection
H3/4 White/Violet No Connection No Connection
H3/5 Violet/Black No Connection No Connection
H3/6 White/Black (-) Hood Switch Input [1] Body ECU on dash fuse box, black 30 pin plug, pin 30 - N.C. Gray
H3/7 Pink/White No Connection No Connection
H3/8 Violet No Connection No Connection
H3/9 Pink No Connection No Connection
H3/10 Blue/White No Connection No Connection
D2D 4-pin white connector (H4)
Module
Conn./Pin Color Description
H4/1 Blue (Data) TX
H4/2 Black (-) Ground
H4/3 Green (Data) RX
H4/4 Red (+) 12 Volt
RF 2-pin white connector (H5)
Module
Conn./Pin Color Description
H5/1 N/A No Connection
H5/2 N/A No Connection
10 403.TL15 1.15 2020 Toyota RAV4 (Smart Key)
©2023 Directed. All rights
Module programming
Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes.
For Convenience-Only programming, see next section.
1Ensure vehicle is in a safe location and cannot move forward during programming.
2
The harnesses must be connected in this exact order:
1. Connect the 14-pin.
2. Connect the 12-pin.
3. Connect the 10-pin.
When the LED turns ON solid red, proceed with the next step.
3Press the Push-to-Start (PTS) button twice (2) to turn the ignition ON.
The LED will flash orange for 3 seconds.
4Wait for the LED to turn ON solid orange.
5Press the PTS button once (1) more to turn the ignition OFF, then twice(2) to turn it back ON.
The LED flashes green then orange.
6Press the PTS button once(1) more to turn the ignition OFF.
7Close all doors including trunk/tailgate then press Lock on the OEM remote.
Wait two (2) seconds then press unlock.
The LED turns ON solid green for 3 seconds then shuts OFF.
You have successfully completed the module programming sequence.
Otros manuales para Directechs DB3
82
Tabla de contenidos
Otros manuales de Electrónica del automóvil de Directed
Directed
Directed DS3+ Manual de usuario
Directed
Directed Directechs DB3 Manual de usuario
Directed
Directed 403.CHRYSLER3 Manual de usuario
Directed
Directed Directechs DB3 Manual de usuario
Directed
Directed DS4+ Manual de usuario
Directed
Directed DS4+ Manual de usuario
Directed
Directed CHRYSLER4 Manual de usuario
Directed
Directed DIRECTECHS HK14 Manual de usuario
Directed
Directed CHRYSLER5 Manual de usuario
