Dimplex BF9000 Manual de usuario

Owner’s Manual

Model

BF9000

7211120100R06

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this replace.

!NOTE: Procedures

and techniques that are

considered important enough

to emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result

in damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations ..................3

Important Instructions .......................4

Fireplace Installation .......................7

Front Glass Installation .........................10

Bathroom Installation. . . . . . . . . . . . . . . . . . . . . . . . . . .10

Operation ................................11

Maintenance .............................13

Warranty ................................16

Replacement Parts .........................19

Model Number Part Number

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric

replace from Dimplex, the world leader in electric replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in a

possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future refer-

ence: model and serial numbers can be found on the Model and Serial

Number Label of your replace.

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

S E R IAL No.

MODE L

MOD.

4 www.dimplex.com

IMPORTANT INSTRUCTIONS

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

① Read all instructions before us-

ing the electric replace.

②The heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. The trim

around the heater outlet becomes

hot during heater operation.

③ Extreme caution is neces-

sary when any heater is used by

or near children or invalids and

whenever the unit is left operating

and unattended.

④ Always unplug the electric

replace when not in use.

⑤ Do not operate any heater after

it malfunctions. Disconnect power

at the service panel and have the

heater inspected by a reputable

electrician before reusing.

⑥ Do not operate any unit with

a damaged cord or plug, or if the

heater has malfunctioned, or if

the electric replace has been

dropped or damaged in any man-

ner, contact Dimplex Technical

Service at 1-888-346-7539.

⑦Do not use outdoors.

⑧ Never locate heater where it

may fall into a bathtub or other

water container.

⑨ Do not run the cord under

carpeting. Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from traf-

c area and where it will not be

tripped over.

⑩ To disconnect the unit, turn the

controls off, then remove the plug

from the outlet

⑪ Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑫ To prevent a possible re, do

not block air intake or exhaust in

any manner.

⑬ All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable

liquids are used or stored.

⑭ Do not modify the electric re-

place. Use it only as described

in this manual. Any other use not

recommended by the manufactur-

er may cause re, electric shock

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

or injury to persons.

⑮ To reduce the risk of electric

shock, this appliance has a polar-

ized plug (one blade is wider than

the other). This plug will t in a

polarized outlet only one way. If

the plug does not t fully in the

outlet, reverse the plug. If it still

does not t, contact a qualied

electrician to install the proper

outlet. Do not change the plug in

any way.

⑯ Always plug heaters directly

into a wall outlet/receptacle.

Never use with an extension cord

or relocatable power tap (outlet/

power strip).

⑰ Do not burn wood or other ma-

terials in the electric replace.

⑱ Do not strike the replace

glass.

⑲ Always use a certied electri-

cian should new circuits or outlets

be required.

⑳ Always use properly grounded,

fused and polarized outlets.

㉑ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

㉒When transporting or stor-

ing the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

6 www.dimplex.com

!NOTE: This equipment has

been tested and found to comply with

the limits for Class B digital device,

pursuant to part 15 of the FCC

Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This equipment

generates, uses and can radiate

radio frequency energy and, if not

installed and used in accordance with

the instructions, may cause harmful

interference to radio or television

reception, which can be determined

by turning the equipment off and

on, the user is encouraged to try to

correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between

the equipment and the receiver.

• Connect the equipment into an

outlet on a circuit different from

that to which the receiver is

connected.

• Consult the dealer or an

experienced radio/TV technician

for help.

Operation is subject to the following

two conditions: (1) this device may

not cause interference and (2) this

device must accept any interference,

including interference that may cause

undesired operation of the device.

WARNING: Remote control

contains small batteries. Keep away

from children. If swallowed, seek

medical attention immediately.

WARNING: Do not install battery

backwards, charge, put in re or mix

with used or other battery types - may

explode or leak causing injury.

!NOTE: Changes or modications

not expressly approved by the party

responsible for compliance could

void user's authority to operate the

equipment.

IMPORTANT INSTRUCTIONS

878"

(225 mm)

24 1/2"

(622 mm)

18 ¼"

(463 mm)

Fireplace Installation

WARNING: Ensure the power

cord is not installed so that it is

pinched or against a sharp edge

and ensure that the power cord is

stored or secured to avoid tripping

or snagging to reduce the risk

of re, electric shock or injury to

persons.

WARNING: Construction

and electrical outlet wiring must

comply with local building codes

and other applicable regulations

to reduce the risk of re, electric

shock and injury to persons.

WARNING: Do not attempt

to wire your own new outlets or

circuits. To reduce the risk of re,

electric shock or injury to persons,

always use a licensed electrician.

WARNING: To reduce the risk

of re, do not store or use gaso-

line or other ammable vapors or

liquids in the vicinity of the heater.

CAUTION: Clearance for air

circulation beneath the re-

place insert is provided by 2

rubber feet.

Do not install the replace

insert directly on carpet or

similar surfaces which may

restrict air circulation.

CAUTION: If installing the

replace in a carpeted area, place

a one-piece, solid, at surface

under the replace. Ensure that

both of the feet rest securely on

this surface.

!NOTE: The dimensions of the

rebox are 30 in. (762 mm)

wide X 18 ⅞ in. (479.5 mm)

high X 9 ¼ in. (235 mm) deep.

The replace does not require

any additional venting.

Mantel Installation

Install the replace into the

mantel (refer to mantel assembly

instructions).

!IMPORTANT: If not using a

Dimplex mantel, the replace

must be installed in an enclosure

with the following minimum inter-

nal/opening dimensions - Figure

Figure 1

8 www.dimplex.com

Figure 2

Feet

Opening

Visible Edges

New Wall Construction

1. Mark the desired location on

the oor and store the re-

place in a safe, dry and dust

free location.

2. Use studs to frame an open-

ing of 24 ½ in. (622 mm) wide

X 18 ¼ in. (463.6 mm) high

X 8 ⅞ in. (225.5 mm) deep.

(Figure 1)

!NOTE: On elevated

installations, the bottom edge

and 1/2" (12.7) up either side will

be easily visible after installation

(Figure 2). This area should

be nished in a manner that is

visually appealing and does not

restrict air ow to the unit.

Option #1 - The power cord can

be lead from behind the trim

and along the wall to an outlet

near the replace.

Option #2 - A new outlet can be

Fireplace Installation

installed inside the new frame

construction. Plug the unit into

a 15 Amp/120 Volt outlet.

!NOTE: A 15 Amp, 120 Volt

circuit is required. A dedicated

circuit is preferred but not es-

sential in all cases. A dedi-

cated circuit will be required

if, after installation, the circuit

breaker trips or fuse blows

on a regular basis when the

heater is operating. Additional

appliances on the same circuit

may exceed the current rating

of the circuit breaker.

Option #3 - Hardwire

1. Wire a dedicated, properly

fused circuit with 120 Volt, 15

Amp rating. Allow up to 8 feet

of service cable for connect-

ing power supply to junction

box on replace when install-

ing after nishing wall.

CAUTION: Use two conduc-

tor, non-metallic sheath cable

with ground wire (3 wires total)

for the incoming power supply on

replace inserts. Use appropriate

wire to meet local and national

electrical codes for rated power

consumption.

2. Remove the outer jacket and

strip the individual conductor

Fireplace Installation

from the end.

3. Loosen the screw securing

the junction box cover and

remove the cover.

4. Take the cables out from the

junction box, loosen the two

wire twist nuts and remove

the cord set (Figure 3).

5. Route the power supply wire

through the knockout on sup-

plied alternative junction box

cover and secure with a wire

clamp (not supplied)

(Figure 4).

6. Connect the black wire (live)

from the unit to the black wire

from power supply (Figure 4).

7. Connect the white wire

(neutral) from the unit to the

white wire from power supply

Figure 4

Figure 3

LED LOG

ASSEMBLY

LED CONTROL

BOARD

SWITCH OUT

CUTOUT THERMOSTAT

HEAT ON/OFF

SWITCH

LIGHT HARNESS

ASSEMBLY

FLICKER

MOTOR

CAPACITOR

BLOWER

MOTOR

ELEMENT

Wiring

10 www.dimplex.com

Fireplace Installation

Front Glass Installation

1. Carefully mount front glass

assembly so that the front

glass hooks (2) hang on the

front glass mounts on the

fireplace (2).

2. Use the supplied two (2)

Phillips sheet metal screws

to fasten the glass assembly

tabs to the fireplace (Figure

5).

3. Ensure the fireplace's

3-Position Switch is switched

to the Off position (refer to

operation section).

4. If unit is not hard-wired, plug

fireplace into a 15 Amp, 120

Volt outlet (refer to NOTE 1).

Figure 5 Tab

(Figure 4).

8. Connect the green wire

(ground) from the unit to the

green wire from power supply

(Figure 4).

9. Place all connectors inside

the unit and secure the junc-

tion box cover to unit. Ensure

that the cable clamp grips

only the jacket of service

cable.

Bathroom Installation

This rebox must be protected

by a GFI receptacle or circuit. If

a receptacle is used it must be

readily accessible.

To prevent electrical shock this

unit is an electrical appliance

that is not watertight and must be

installed as to prevent water from

entering the unit. This unit must

be installed away from showers,

tubs, etc. Never locate replace

where it may fall into a bathtub or

other water containers.

Otros manuales para BF9000

Tabla de contenidos

Otros manuales de Chimenea de interior de Dimplex

Dimplex

Dimplex BFSL33 Manual de usuario

Dimplex

Dimplex DF2690 Manual de usuario

Dimplex

Dimplex Opti-V PGF10 Manual de usuario

Dimplex

Dimplex Amesbury AME20 Manual de usuario

Dimplex

Dimplex Revillusion RBF24DLX Manual de usuario

Dimplex

Dimplex ELECTRALOG CFP3913 Manual de usuario

Dimplex

Dimplex RBF30-AU Manual de usuario

Dimplex

Dimplex BLF74 Manual de usuario

Dimplex

Dimplex Diamantique Manual de usuario

Dimplex

Dimplex 30" FIREPLACE Manual de usuario

Dimplex

Dimplex MULTIFIRE DF3015 Manual de usuario

Dimplex

Dimplex DF2690 Manual de usuario

Dimplex

Dimplex SP1 Wallfire Manual de usuario

Dimplex

Dimplex Indoor Fireplace Manual de usuario

Dimplex

Dimplex Optimyst 3STEP-RGB-EU Manual de instrucciones

Dimplex

Dimplex TFA36E Manual de usuario

Dimplex

Dimplex DF3020-EU Manual de usuario

Dimplex

Dimplex Devon Manual de usuario

Dimplex

Dimplex XLF5017-XD Manual de usuario

Dimplex

Dimplex IN-STUD V1525BT Manual de usuario

Dimplex

Dimplex Indoor Electric Fireplace Manual de usuario

Dimplex

Dimplex DFG2562 Manual de usuario

Dimplex

Dimplex Nicole Manual de usuario

Dimplex

Dimplex DF2524L Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación