Dimplex Prism Series Manual de usuario

Owner’s Manual

Model

BLF5051

7213940100R09

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician or

service agency to repair this replace.

!NOTE: Procedures and tech-

niques that are considered impor-

tant enough to emphasize.

CAUTION: Procedures and

techniques which, if not carefully

followed, will result in damage to

the equipment.

WARNING: Procedures and

techniques which, if not carefully

followed, will expose the user to

the risk of re, serious injury, or

death.

Welcome & Congratulations ..................3

IMPORTANT INSTRUCTIONS ...............4

Quick Reference Guide ......................6

Fireplace Installation ........................7

Site Selection .....................................7

Installation .......................................9

Hardwire Installation ...............................9

For Bathroom Use ................................11

Surface Installation ...............................12

Partial Recess Installation - 2x4 Framing ..............13

Flush Mounted Installation - 2x8 Framing ..............14

Installation in a Dimplex Mantel ......................15

Front Glass Installation ............................16

Operation ................................17

Maintenance .............................21

Warranty .................................22

Technical Support .........................24

Welcome & Congratulations

Thank you and congratulations for purchasing an electric replace from

Dimplex. Please use our convenient online registration page to record

your model and serial numbers for future reference at

www.dimplex.com/register

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-346-7539

In order to better serve you, please have your model and serial number

ready or register your product online before calling (See above)

Serial Number

Label Rating Label with

Model Number

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in

a possible electric shock, re hazard and will void the warranty.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always be

followed to reduce the risk of fire,

electric shock, and injury to persons,

including the following:

① Read all instructions before using

this electric replace.

② This replace is hot when in

use. To avoid burns, do not let

bare skin touch hot surfaces.

The surface around the heater

outlet becomes hot during heater

operation.

DANGER: High temperatures

may be generated under certain

abnormal conditions. Do not

partially, fully cover, or obstruct

the front of this heater.

③Extreme caution is necessary

when any heater is used by or

near children or invalids and

whenever the unit is left operating

and unattended.

④Young children should be

supervised to ensure that they do

not play with the appliance.

⑤ The appliance is not intended for

use by young children or inrmed

persons without supervision.

⑥Do not operate any heater after

it malfunctions. Disconnect

power at service panel and have

heater inspected by a reputable

electrician before reusing.

IMPORTANT INSTRUCTIONS

⑦ If the supply cord is damaged,

it must be replaced by the

manufacturer, its service agent,

or a qualied person in order

to avoid a hazard. Contact

Technical Service for obtaining a

replacement cord at

1-888-346-7539.

⑧ Do not use outdoors.

⑨Never locate replace where it

may fall into a bathtub or other

water container.

⑩ Do not locate the heater

immediately below a xed socket-

outlet.

⑪ To disconnect the replace, turn

the controls o󰀨, and turn o󰀨

power to heater circuit at main

disconnect panel.

⑫Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause electric shock, re, or

damage to the heater.

⑬ To prevent a possible fire, do not

block air intakes or exhaust in

any manner.

⑭ A heater has hot and arcing or

sparking parts inside. Do not use

in areas where gasoline, paint,

or ammable liquids are used or

stored.

SAVE THESE INSTRUCTIONS

⑮Use this heater only as

described in this manual. Any

other use not recommended by

the manufacturer may cause

fire, electric shock, or injury to

persons.

⑯ To reduce the risk of electric

shock, this appliance has a

polarized plug (one blade is

wider than the other). This plug

will fit in a polarized outlet only

one way. If the plug does not fit

fully in the outlet, reverse the

plug. If it still does not fit, contact

a qualified electrician to install

the proper outlet. Do not change

the plug in any way. Always plug

heaters directly into a wall outlet/

receptacle. Never use with an

extension cord or relocatable

power tap (outlet/power strip).

⑰Do not burn wood or other

materials in the electric replace.

⑱ Do not strike the replace glass.

⑲ Always use a certied electrician

should new circuits or outlets be

required.

⑳ Always use properly grounded,

fused and polarized outlets.

㉑ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

㉒ When transporting or storing

the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

WARNING: Remote control

contains small batteries. Keep

away from children. If swallowed,

seek medical attention

immediately.

WARNING: Do not install battery

backwards, charge, put in re,

or mix with used or other battery

types - may explode or leak

causing injury.

!NOTE: Changes or modications

not expressly approved by the

party responsible for compliance

could void user's authority to

operate the equipment.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICABLE PARTS INSIDE

IMPORTANT INSTRUCTIONS

6 www.dimplex.com

Quick Reference Guide

Figure 1

① The electrical information

regarding your electric replace

can be found on the rating label

located on the front of the unit,

behind the glass.

Please use our convenient online

registration page to record your

model and serial numbers for future

reference at

www.dimplex.com/register

② If you have any technical

questions or concerns regarding

the operation of your electric

replace, or require service

contact customer service.

③ For dimensions of your replace,

refer to Figure 1.

3" (7.6 cm)

50 516" (128 cm)

19 12

(49.5 cm)

46" (116 cm)

48 12 " (123 cm)

(17.8 cm)

3 1316"

(9.7 cm)

18"

(45.7 cm)

16"

(40.6 cm)

Site Selection

Review and consider all of the

following conditions for installation:

• Dimensions of the unit: 50

(128 cm) x 19½"(49.5 cm)

• Unit requires a minimum of two wall

studs in order to ensure a secure

installation

There are three possible mounting

methods:

• Surface mount (pg. 12);

• Partial recess (pg. 13);

• Flush mount (pg. 14),

and any of these have the option of

being hardwired or plugged directly

into the wall outlet.

WARNING: The top of the

replace is to be installed at least

4" (10.2 cm) from the ceiling.

CAUTION: Ensure installation

does not allow replace to be in

direct contact with building vapor

barrier or insulation and meets all

local building codes.

NOTE 1: A 15 Amp, 120 Volt

circuit is required. A dedicated

circuit is preferred but not essential

in all cases. A dedicated circuit will

be required if, after installation, the

circuit breaker trips or fuse blows

on a regular basis when the heater

is operating. Additional appliances

on the same circuit may exceed

Fireplace Installation

the current rating of the circuit

breaker.

WARNING: Ensure the power

cord is not installed so that it is

pinched or against a sharp edge

and ensure that the power cord

is stored or secured to avoid

tripping or snagging to reduce

the risk of re, electric shock or

injury to persons. Construction and

electrical outlet wiring must comply

with local building codes and other

applicable regulations to reduce

the risk of re, electric shock and

injury to persons.

WARNING: To reduce the risk of

re, do not store or use gasoline,

or other ammable vapors or

liquids in the vicinity of the heater.

8 www.dimplex.com

Fireplace Installation

Grounding Instructions

This product must be grounded. If it

should malfunction or breakdown,

grounding provides a path of least

resistance for electric current to

reduce the risk of electric shock.

This product is equipped with a cord

having an equipment-grounding

conductor and a grounding plug.

The plug must be plugged into an

appropriate outlet that is properly

installed and grounded in accordance

with all local codes and ordinances.

DANGER: Improper connection

of the equipment-grounding

conductor can result in a risk

of electric shock. Check with a

qualied electrician or serviceman

if you are in doubt as to whether

the product is properly grounded.

Do not modify the plug provided with

the product – if it will not t the outlet,

have a proper outlet installed by a

qualied electrician.

This product is for use on a nominal

120-volt circuit and has a grounding

plug that looks like the plug in Figure

3. Make sure that the product is

connected to an outlet having the

same conguration as the plug. No

adapter should be used with this

product.

Figure 2

MOTOR

HEATER NEUTRAL

FLAME COLOR

TOP LIGHT

LOG MEDIA NTC

GESTURE DISPLAY

FAN

LINE

FLAME

MOTOR

LED CONTROL

BOARD

LED LIGHTS

NTC

MOTOR

HEATER

ELEMENT

CUTOUT

THERMAL

BLOWER

MOTOR

LINE

LED LIGHTS

LED LIGHTS LED LIGHTS

LED LIGHTS

SWITCH

BOARD

DISPLAY

BOARD

120V~

60Hz

Wiring

Figure 3

Partially

Reective Glass

Glass Bracket

Bracket Screws

Installation

1. Select a location that is not

susceptible to moisture and is away

from drapes, furniture and high

tra󰀩c.

2. For ease of electrical hook up, you

may wish to locate the replace

near an existing outlet (for plug-in

convenience) (refer to NOTE 1,

page 7).

3. Remove replace, front glass and

hardware from box and remove

all packaging materials before

installation.

4. Store the replace in a safe, dry and

dust-free location until you are ready

to install the replace.

Fireplace Installation

Hardwire Installation

The replace is packaged with a

three-prong plug installed for plug-in

convenience. Hardwiring the replace

is also an option for any installation.

WARNING: Do not attempt to wire

your own new outlets or circuits.

To reduce the risk of re, electric

shock or injury to persons, always

use a licensed electrician.

WARNING: Ensure that the circuit

on which the replace is to be

installed has the power cut o󰀨 at

the service panel until installation

is complete.

1. Remove the partially reective

glass from the replace:

• Lay replace on its back.

• Remove two Phillips screws from

each of the two glass brackets

(Figure 3).

• Remove the glass brackets.

• With one hand keeping pressure

on the partially reective glass, tilt

the replace upright and slightly

forward to allow the partially

reective glass to fall out of the

inside framing.

CAUTION: Do not bump or drop

the partially reective glass to

avoid breakage and personal

injury.

10 www.dimplex.com

Fireplace Installation

• Remove the partially reective

glass from the replace.

2. Locate the power cord and

remove the 3 screws that attach

the cord bracket to the unit - one

on the back of the unit and two on

the bottom. (Figure 5)

3. From the front, remove the 2

Philips screws that fasten the front

panel tabs, tilt the panel forward

and lift o󰀨. (Figure 4)

4. Remove the 4 screws that fasten

the acrylic media tray, and the 2

screws that attach the metal tray

to the unit.

The metal tray cannot be removed

but will now allow the ability to

remove the junction cover.

5. Remove the Phillips screw to

release the junction cover in the

bottom right corner of the replace

(Figure 6).

6. Carefully slide the junction cover

to the right to release the securing

tabs, as wires are fed through the

strain reliefs on the junction cover

and are connected within.

7. Unscrew the 3 wire connectors

under the junction cover and

separate the wires (Figure 7).

8. Pull the cord bracket and power

cord out the front of the replace.

9. Replace removed cord bracket

with the supplied hardwire bracket

replacement (Figure 8) and install

using screws removed in step 2.

Figure 6

Junction Cover

Screw

Figure 5

Screws

Hardwire

Bracket

Cord

Bracket

Front Panel

Front Panel tabs (2)

Acrylic Tray screws (4) Metal Tray

Screws (4)

Figure 4

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Chimenea de interior de Dimplex

Dimplex

Dimplex WESTBROOK Manual de usuario

Dimplex

Dimplex STOCKBRIDGE SKG20BL Manual de usuario

Dimplex

Dimplex BLF3451 Manual de usuario

Dimplex

Dimplex WBK20 Manual de usuario

Dimplex

Dimplex Electric fireplaces Manual de usuario

Dimplex

Dimplex THWG XLF50 Manual de usuario

Dimplex

Dimplex DF28L-PRO Manual de usuario

Dimplex

Dimplex DF2608 Manual de usuario

Dimplex

Dimplex DFOP25 Manual de usuario

Dimplex

Dimplex 7206560100R00 Guía de instalación

Dimplex

Dimplex TOLUCA TLC20 Manual de instrucciones

Dimplex

Dimplex Silverton SVT20 Manual de usuario

Dimplex

Dimplex Figaro FGA15 Manual de usuario

Dimplex

Dimplex MULTI-FIRE SL PLF3614-XS Manual de usuario

Dimplex

Dimplex Charlotte CRT20BR Manual de usuario

Dimplex

Dimplex DF2426GB Manual de usuario

Dimplex

Dimplex BLF50-UK Manual de usuario

Dimplex

Dimplex SP420 Manual de usuario

Dimplex

Dimplex DF2624L Manual de usuario

Dimplex

Dimplex KTN20-AU Manual de usuario

Dimplex

Dimplex SARATOGA SGA20 Manual de usuario

Dimplex

Dimplex CASSIDY Manual de usuario

Dimplex

Dimplex IN-STUD V1525BT Manual de usuario

Dimplex

Dimplex BEETHOVEN Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación