Dimplex Opti-myst Pro CDFI-BX1500 Manual de usuario

Owner’s Manual

Model

CDFI-BX1500

6910370100

7216190100R01

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use the Opti-myst®Pro Box Heater. For

your safety, always comply with all warnings and safety instructions

contained in this manual to prevent personal injury or property

damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this unit.

!NOTE: Procedures and

techniques that are considered

important enough to

emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations .................. 3

Important Instructions ....................... 4

Installation ................................ 6

Operation ................................ 12

Maintenance ............................. 13

Warranty................................. 14

Technical Support ......................... 16

Welcome & Congratulations

Thank you and congratulations for purchasing an Opti-myst Pro Box

Heater from Dimplex. Please use our convenient online registration

page to record your model and serial numbers for future reference at

www.dimplex.com/register

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-346-7539

In order to better serve you, please have your model and serial number

ready or register your product online before calling (See above)

Model Number

and Serial

Number

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in

a possible electric shock, re hazard and will void the warranty.

Please carefully

read and save these

instructions.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

①Read all instructions before

using the heater.

②The heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. The

surface around the heater

outlet becomes hot during

heater operation.

DANGER: High temperatures

may be generated under

certain abnormal conditions.

Do not partially or fully cover or

obstruct the front of this heater.

③Extreme caution is necessary

when any heater is used by

or near children or invalids

and whenever the unit is left

operating and unattended.

④Do not operate any heater

after it malfunctions.

Disconnect power at the

service panel and have

the heater inspected by a

reputable electrician before

reusing.

IMPORTANT INSTRUCTIONS

⑤ Do not operate any unit with a

damaged cord or if the heater

has malfunctioned, or if the

heater

has been dropped or damaged

in any manner, contact

Glen Dimplex Americas

Technical Service at 1-888-

346-7539.

⑥Do not use outdoors.

⑦Never locate heater over

a bathtub or other water

container.

⑧To disconnect the unit, turn

the controls OFF, disconnect

power at the service panel.

⑨Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this

may cause an electric shock or

re, or damage to the heater.

⑩ To prevent a possible re, do

not block air intake or exhaust

in any manner.

⑪All electrical heaters have hot

and arcing or sparking parts

inside. Do not use in areas

where gasoline, paint, or

ammable liquids are used or

stored.

SAVE THESE INSTRUCTIONS

⑫Do not modify the heater.

Use it only as described in

this manual. Any other use

not recommended by the

manufacturer may cause

re, electric shock or injury to

persons.

⑬ Always use a certied

electrician should new circuits

or outlets be required.

⑭Always use properly grounded,

fused and polarized outlets.

⑮ Disconnect all power supply

before performing any

cleaning, maintenance or

relocation of the unit.

⑯ When transporting or storing

the unit, keep in a dry place,

free from excessive vibration

and store so as to avoid

damage.

IMPORTANT INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

!NOTE: Changes or

modications not expressly

approved by the party

responsible for compliance

could void user's authority to

operate the equipment.

For Bathroom Use

If this unit is installed in a

bathroom it must be protected

by a GFI receptacle or circuit.

If receptacle is used it must be

readily accessible.

To prevent electrical shock this

unit is an electrical appliance

that is not watertight and must

be installed as to prevent water

from entering unit. This must be

installed away from showers,

tubs, etc. Never locate replace

where it may fall into a bathtub or

other water container.

6 www.dimplex.com

Installation

WARNING: ANY

INSTALLATION AND

SERVICE WORK SHOULD BE

PERFORMED BY QUALIFIED AND

AUTHORIZED PERSONNEL. ALL

INSTALLATIONS MUST COMPLY

WITH ALL LOCAL CODES AND

BY-LAWS, AND INSPECTED AND

APPROVED FOR OPERATION BY

LOCAL GOVERNING AUTHORITY

PRIOR TO USE.

WARNING: Construction and

electrical wiring must comply

with local building codes and

other applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

Opti-myst Cassette

The Opti-myst Pro Box Heater works

exclusively with the Opti-myst

Cassette (CDFI1000-PRO and

CDFI500-PRO). Controls for the

heater are found on the

CDFI500-PRO cassette.

New Construction

When determining a location for the

Opti-myst

Pro Box Heater, ensure

that the unit will not be susceptible to

drafts, vents, ceiling fans and other

air currents. Similar to a candle,

large movements of air will a󰀨ect the

unit's ability to create and maintain

the ame e󰀨ect.

Hardwire Installation

The Opti-myst Pro Box Heater is

supplied in an assembled state

and is designed to be permanently

installed. The unit comes ready for

hardwire installation.

WARNING: Do not attempt

to wire your own new outlets or

circuits. To reduce the risk of

re, electric shock or injury to

persons, always use a licensed

electrician.

NOTE:

Please read all

instructions before installing

1. For rough in framing, the

opening should follow the

recommended dimensions

located in Figure 1.

!NOTE: Dimensions provided

are minimum clearances and

will vary depending on type of

support framing and nishing

options.

!NOTE: Framing should be

constructed to support 160 lbs

(73 kg)

WARNING: To reduce the

risk of re, do not store or use

gasoline or other ammable

vapours or liquids in the vicinity

of the unit.

Installation

!NOTE: Use minimum 14 AWG

supply cable with two insulated copper

conductors (white and black) and one

bare ground wire.

A B C D E F G H I

CDFI-

BX1500

65"

(165 cm)

31.75"

(80.5 cm)

14.7"

(37.3 cm)

9.5"

(24 cm)

4.8"

(12.2 cm)

15.5"

(39.3 cm)

16.2"

(41.2 cm)

65.4"

(166.2 cm)

32.3"

(82 cm)

Figure 1

2. Allow at least 4 ft. (122 cm) of service

cable for connecting a power supply wire

to the Opti-myst Cassette when installing

before nishing wall.

!NOTE: A 15 amp, 120 volt alternating

current (VAC) circuit is required. A dedicated

circuit is preferred but not essential in all

cases. A dedicated circuit will be required if,

after installation, the circuit breaker trips or

the fuse blows on a regular basis when the

heater is operating. Additional appliances

on the same circuit may exceed the current

rating of the circuit breaker.

Mounting

Flanges Heater

Exhausst

8 www.dimplex.com

Installation

Do not use cable with aluminum

conductors.

!NOTE: It is recommended

that all drywall installation and

nishing be completed after unit

is fully installed.

3. The Opti-myst Pro Box Heater

can be installed as a one-sided

or two-sided unit. The unit comes

assembled in the one-sided

conguration. The four anges

on the back can be removed

if there is not enough depth in

the framing to properly t the

unit. For two-sided installation,

remove the anges so that the

back panel can be removed.

Replace the anges. (Figure 2)

!NOTE: The heater only exhausts

from one direction. Note this

direction when installing in a two-

sided conguration.

CAUTION: When inserting the

unit take care not to damage or

pinch any of the power cables

that are concealed in the wall.

4. Mount the Opti-myst Pro Box

Heater to the framing with

the mounting brackets using

appropriate screws for the

application. (Figure 1)

5. Feed the wire through the

opening on the back left of the

Opti-myst Pro Box Heater

(Figure 3). Remove the outer

jacket and strip the individual

conductors ½ in. (1.3 cm) from

the end.

6. Do not remove cardboard

backing from the Opti-myst Pro

Box Heater until the Opti-myst

Cassette is installed. This will

help prevent scratches and

damage to the sides of the Opti-

myst Pro Box Heater.

7. Follow the installation

instructions provided with the

Opti-myst Cassettes to install

within the Opti-myst Pro Box

Heater. Use the provided

screws to fasten the cassettes

to the Opti-myst Pro Box Heater

through the holes in the cassette.

(Figure 4)

Figure 2

Back Panel

Flange

Installation

Figure 4

Cable Plate

Electrical Cover Plate

Holes for

securing to

framing

Flange

Back Panel

Plumbing

Routing

Wire

Routing

8. In the back left corner of the

Opti-myst Cassettes, locate and

remove the electrical cover plate

by removing the two securing

screws. (Figure 4)

Remove the top of the junction

box using the 2 screws. On the

left side, install the power supply

cable through a cable connector

(not included) suitable for a 7/8''

(22mm) hole. (Figure 5)

CAUTION:

Use two conductor,

non-metallic sheath cable with

ground wire (3 wires total) for the

incoming power supply on the

cassette and junction box. Use

appropriate wire to meet local

and national electrical codes for

rated power.

Figure 3

Supply Cable Entrance

Figure 5

To CDFI1000-PRO

To CDFI500-PRO

10 www.dimplex.com

10.

Using the existing screws from

the Opti-Myst cassettes, attach

one of the cords from the

junction box to the CDFI500-Pro,

and the other to the CDFI1000-

Pro using the brackets provided.

(Figure 6)

Installation

11.

Within the junction box connect

the black wires (live) from the

Opti-Myst cassettes and the

Opti-Myst Pro Box Heater to the

live from the power supply. Then

within each cassette, connect

the black wires from the junction

box to the live from the Opti-

Myst Cassette. (Figure 7)

12.

Within the junction box connect

the white wires (neutral) from

the Opti-Myst cassettes and the

Opti-Myst Pro Box Heater to the

neutral from the power supply.

Then within each cassette,

connect the white wires from the

junction box to the neutral from

the Opti-Myst Cassette.

(Figure 7)

CDFI-BX1500

JUNCTION BOX

120V

POWER SUPPLY

PRO BOX

RELAY BOARD CDFI500-PRO

CDFI1000-PRO

WHITE-NWHITE-N

WHITE-N WHITE-N

BLACK-L

BLACK-LBLACK-L

BLACK-L

GREEN-G

GREEN-G GREEN-G

GREEN-G

Cassette

Bracket

Existing

screws

Figure 6

Figure 7

Tabla de contenidos

Idiomas:

Otros manuales de Calentador de Dimplex

Dimplex

Dimplex MFP Series Manual de usuario

Dimplex

Dimplex RSH Series Manual de usuario

Dimplex

Dimplex DXC20 Manual de usuario

Dimplex

Dimplex DHCER20 Manual de usuario

Dimplex

Dimplex EUH02B21T Manual de usuario

Dimplex

Dimplex LST050E Manual de usuario

Dimplex

Dimplex BFH24T Manual de usuario

Dimplex

Dimplex DXFF20TSN Manual de usuario

Dimplex

Dimplex LYDON Manual de usuario

Dimplex

Dimplex DHCERA20E Manual de usuario

Dimplex

Dimplex CHILTON CHDF20 Manual de usuario

Dimplex

Dimplex 7150B11 Manual de usuario

Dimplex

Dimplex BPH100M Manual de usuario

Dimplex

Dimplex KBE 50 Manual de usuario

Dimplex

Dimplex CKHA Manual de usuario

Dimplex

Dimplex RPX Series Manual de usuario

Dimplex

Dimplex EVX050 Manual de usuario

Dimplex

Dimplex CXD2000VE Manual de usuario

Dimplex

Dimplex PLXE Series Manual de usuario

Dimplex

Dimplex DES 1821 Manual de usuario

Dimplex

Dimplex OFRB14 Manual de usuario

Dimplex

Dimplex PLXE Series Manual de usuario

Dimplex

Dimplex DXGLO2 Manual de usuario

Dimplex

Dimplex BEETHOVEN Manual de usuario

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario